校正代码 18301000 0.96 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

1. Open the LH front door.
2. Lower the LH front window.
3. Activate Service Mode using the touchscreen.

   

   

4. Press brake pedal to turn on drive rails

   

5. Set air suspension ride height to “Very High”
   注

   Via center display > Controls > Suspension > ''Very High''

   

6. Turn steering wheel fully to the right

   

7. Open the hood.

   

8. Remove the rear underhood apron.

   

   

9. Remove the LH underhood apron.

   

   

   

   

10. Remove the RH underhood apron.

    

    

    

    

11. Remove the front underhood apron.

    

    

12. Remove the underhood storage unit access panel.

    

    

13. Remove the underhood storage unit carpet.

    

    

14. Remove the underhood storage unit from the vehicle.

    

    

15. Remove bolts securing upper portion of front fascia
    注

    6x bolts, 10mm, 7 Nm

    

16. Remove fasteners securing LH front wheel liner to valence
    注

    1x bolt, T30, 1.5 Nm, 3x clips, Move front portion of wheel liner backwards to access fairing

    

    

    

17. Remove LH front wheel fairing from valence
    注

    2x bolts, 10mm, 1.5 Nm, 1x securing tab

    

18. Partially remove front portion of LH front fender garnish
    注

    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish

    

    

19. Remove bolt securing LH front of fascia to LH front fender
    注

    1x bolt, 8mm, 1.5 Nm

    

20. Press brake pedal to turn on drive rails

    

21. Turn steering wheel fully to the left

    

22. Remove clips securing RH front wheel liner to valence
    注

    4x clips, Move front portion of wheel liner backwards to access fairing

    

    

23. Remove RH front wheel fairing from valence
    注

    2x bolts, 10mm, 1.5 Nm, 1x securing tab

    

24. Partially remove front portion of RH front fender garnish
    注

    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish

    

    

25. Remove bolt securing RH front of fascia to RH front fender
    注

    1x bolt, 8mm, 1.5 Nm

    

26. Power off the vehicle using the touchscreen.

    

27. Disconnect the LV battery connector and First Responder Loop.

    

    

    

28. Remove fasteners securing lower portion of front fascia to valence
    注

    3x bolts, 10mm, 3 Nm, 2x clips

    

    

    

    

29. Apply masking tape to protect LH and RH front fenders

    

    

30. Disconnect front fascia assembly
    注

    1x connectors, Release locking tabs then disconnect

    

    

    

31. Remove front fascia assembly from vehicle
    注

    Recommend assistance, Release fascia from LH and RH fender brackets, Careful not to damage the fender bracket when removing fascia, Place on protected surface to avoid damage

    

    

    

32. Disconnect active grille shutter actuator
    注

    1x connector, Release locking tab

    

33. Disconnect ambient air sensor and push grommet through front end carrier
    注

    1x connector, 1x grommet

    

    

34. Remove ambient temperature sensor from active grill shutter assembly
    注

    1x clip, Squeeze retaining arms on clip and remove downward

    

    

    

    

35. Release locking tabs securing active grille shutter to cooling fan module assembly and remove active grille shutter through front of vehicle
    注

    12x locking tabs, 2x clips

    

    

    

    

    

    

    

36. Remove plastic grille from the radiator
    注

    9x locking tabs

    

    

    

37. Use shop-vac to clean dirt on the radiator
    注

    If necessary removeal large debris

    

38. Use blow gun to clean dirt on the radiator again
    注

    Do not get too close to the radiator blades

    

39. Install plastic grille to the radiator
    注

    9x locking tabs

    

    

    

40. Install active grille shutter to cooling fan module assembly
    注

    12x locking tabs, 2x clips, Align datums before engaging tabs, Make sure shutter slides inside tab not outside

    

    

    

    

    

    

    

41. Install ambient temperature sensor into active grill shutter assembly
    注

    1x clip, 1x datum, Align datum with opening in active grill shutter assembly

    

    

    

42. Connect ambient air sensor and secure grommet onto active grille shutter
    注

    1x connector, 1x grommet

    

    

43. Connect active grille shutter actuator
    注

    1x connector, Engage locking tab

    

44. Connect front fascia harness onto frunk harness
    注

    1x connectors, Engage locking tab, Located behind RH wheel arch liner

    

    

    

45. Install front fascia onto vehicle
    注

    Recommend assistance, Slide LH and RH side of fascia into fenders, Careful not to damage the fender bracket when installing fascia

    

    

    

46. Install fasteners securing lower portion of front fascia to valence
    注

    3x bolts, 10mm, 3 Nm, 2x clips

    

    

    

    

47. Remove masking tape from front fenders

    

    

48. Install bolt securing fascia to RH fender bracket
    注

    1x bolt, 8mm, 5 Nm

    

49. Install RH front fender garnish
    注

    2x clips, 8x tabs, Secure from top to bottom of front bumper

    

    

    

50. Install RH front wheel fairing to valence
    注

    2x bolts, 10mm, 1.5 Nm

    

51. Install push clips securing RH front wheel liner onto fascia
    注

    4x clips

    

    

52. Connect the First Responder Loop and LV battery connector.

    

    

53. Press brake pedal to turn on drive rails

    

54. Turn steering wheel fully to the right

    

55. Install bolt securing fascia onto LH fender bracket
    注

    1x bolt, 8mm, 5 Nm

    

56. Install LH front fender garnish
    注

    2x clips, 8x tabs, Secure from top to bottom of front bumper

    

    

    

57. Install LH front wheel fairing to valence
    注

    2x bolts, 10mm, 1.5 Nm, 1x securing tab

    

58. Install fasteners securing LH front wheel liner to valence
    注

    1x bolt, T30, 1.5 Nm, 3x clips

    

    

    

59. Install bolts securing upper portion of front fascia
    注

    4x bolts, 10mm, 7 Nm, Ensure proper fascia-to-headlamp gap and flushness

    

60. Install the underhood storage unit.

    

61. Install the underhood storage unit carpet.

    

    

62. Install the underhood storage unit access panel.

    

    

63. Install the front underhood apron.

    

    

64. Install the LH underhood apron.

    

    

    

    

65. Install the RH underhood apron.

    

    

    

    

66. Install the rear underhood apron.

    

    

67. Close the hood.
68. Unlock Gateway
    注

    After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information

    

    

69. Perform Thermal Performance via Service UI
    注

    Select Thermal > Actions > Test Thermal Performance, click Run, close once routine is completed

    

    

    

    

70. Perform HVAC Performance via Service UI
    注

    Select Thermal > Actions > Test HVAC Performance, click Run, close once routine is completed

    

    

    

    

71. 运行 ODIN 例行程序 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox: (link)
72. Calibrate the RH falcon wing door.

    

73. Calibrate the LH falcon wing door.

    

74. Turn steering wheel back to center

    

75. Set air suspension ride height to Medium
    注

    Using center display > Suspension > Medium/Standard

    

76. Raise the LH front window.
77. Close the LH front door.