11/02/2024 07:30:53

压缩机、超级歧管和空调管路(拆卸和更换)

校正代码 18204012 2.34 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com 注意:执行下述程序时,请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

  • 2024-2-6: Cleaned up topic.
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
尽管此程序已经过验证,但仍是一个草案。可能没有警告和注意事项。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com

拆卸

  1. Remove the A/C compressor. See 空调压缩机(拆卸和更换).
  2. Remove the NVH acoustic cover from the new AC compressor, and then remove any remaining adhesive material from the compressor.
    Informational PurposesAn informational icon, calling your attention
    The NVH acoustic cover must be fully removed to properly weigh the compressor.
    Informational PurposesAn informational icon, calling your attention
    Remove as much adhesive material from the NVH acoustic cover as possible. Excessive material left on compressor will cause an inaccurate weight measurement.
    提示: 推荐使用以下工具:
    • Flat scraper blade
    • Wire brush
  3. Remove the transportation plugs from the new A/C compressor.
    提示: 推荐使用以下工具:
    • 13 毫米套筒
    • 回旋头棘轮/回旋头扭矩扳手
  4. Weigh the new A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    The new compressor should weigh 7193g. Escalate if the compressor weight is incorrect.
    提示: 推荐使用以下工具:
    • Weighing scale - 1067799-00-A
  5. Install a new NVH blanket on the new A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    Reuse the old NVH blanket if a new one is not available and the adhesive is in good working condition.
    1. Remove the new NVH blanket adhesive backing, and then lay the NVH acoustic cover down with the adhesive side facing upwards.
    2. Align the NVH acoustic cover cut outs to the suction port on the A/C compressor.
    3. Install the NVH acoustic cover around the suction port on the A/C compressor, and then continue to wrap the NVH cover around the compressor.
  6. Position the A/C compressor bracket on the compressor, and then install the bolts (x3) that attach the bracket to the compressor.
    9 Nm (6.6 lbs-ft)
    提示: 推荐使用以下工具:
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
    • 棘轮/扭矩扳手
  7. Disconnect the A/C machine hoses from the A/C flush adapters.
    提示: 推荐使用以下工具:
    • Heat pump flush kit - 1600279-00-A
    • Mastercool 2000 R134A A/C Machine - 1509224-00-A
  8. Remove the supermanifold. See 超级歧管(拆卸和更换).