2024-02-06

Carpet - Rear (Remove and Replace)

Correction code 1530020032 FRT 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure.NOTE: See 인체공학적 주의 사항for safe and healthy working practices.

Remove

  1. 센터 콘솔 후면 엔드 패널을 탈거합니다.참조 항목: Panel - Rear End - Center Console (Remove and Replace).
  2. LH 및 RH 2열 시트 사이드 볼스터를 탈거합니다.참조 항목: Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  3. 2열 하단 시트 쿠션을 탈거합니다.참조 항목: Seat Cushion - 2nd Row (Remove and Replace).
  4. LH 계기판 엔드캡을 탈거합니다.참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  5. LH 하단 A필러 트림을 탈거합니다.참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. LH 하단 B필러 트림을 탈거합니다.참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  7. RH 하단 A필러 트림을 탈거합니다.참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  8. RH 하단 B필러 트림을 탈거합니다.참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  9. LV 전원을 연결 해제합니다.참조 항목: LV Battery - Li-lon (Disconnect and Connect) (Modify).
  10. 전면 동승석 시트를 탈거합니다.참조 항목: Seat Assembly - 1st Row - No Lumbar - RH (Remove and Replace).
  11. 운전석 시트를 탈거합니다.참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  12. 후면 메인 실내 카펫을 차체에 고정하는 푸시 클립(4개)을 풉니다.
  13. 차량에서 후면 메인 실내 카펫을 탈거합니다.

Install

  1. 후면 메인 실내 카펫을 차량에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    푸시 클립(4개)으로 후면 카펫을 고정합니다.
  2. 운전석 시트를 장착합니다.참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  3. 전면 동승석 시트를 장착합니다.참조 항목: Seat Assembly - 1st Row - No Lumbar - RH (Remove and Replace).
  4. LV 전원을 연결합니다.참조 항목: LV Battery - Li-lon (Disconnect and Connect) (Modify).
  5. RH 하단 B필러 트림을 장착합니다.참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  6. RH 하단 A필러 트림을 장착합니다.참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. LH 하단 B필러 트림을 장착합니다.참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  8. LH 하단 A필러 트림을 장착합니다.참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  9. LH 계기판 엔드캡을 장착합니다.참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  10. 2열 하단 시트 쿠션을 장착합니다.참조 항목: Seat Cushion - 2nd Row (Remove and Replace).
  11. LH 및 RH 2열 시트 사이드 볼스터를 장착합니다.참조 항목: Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  12. 센터 콘솔 후면 엔드 패널을 장착합니다.참조 항목: Panel - Rear End - Center Console (Remove and Replace).