11/02/2024 07:32:25

Harness - AC Filter (Remove and Replace)

교정 코드 1630010112 FRT 0.84 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

  1. Open all four doors.
    Informational PurposesAn informational icon, calling your attention
    참고
    If vehicle is being powered down, Latch rear doors to prevent accidental closure.
  2. Lower all four windows.
  3. Move LH front seat forward.
  4. Move RH front seat forward.
  5. Open hood.
  6. Remove rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    참고
    14x clips.
  7. Power off vehicle from center display.
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box.
  8. Disconnect LV battery and First Responder Loop.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge.
  9. Release 2nd row seat cushion and disconnect harness.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 2x connectors, Press tabs backward then pull front edge up.
  10. Verify operation of multimeter.
    Informational PurposesAn informational icon, calling your attention
    참고
    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing the 16v battery.
  11. Remove all items from pockets and ensure not wearing metal items.
  12. Inspect HV insulating gloves.
    Informational PurposesAn informational icon, calling your attention
    참고
    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
  13. Put on HV insulating gloves and leather over gloves.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure to wear Electrical Protective Gloves any time Hioki tester is used.
  14. Remove bolts securing ancillary bay probe lid cover to ancillary bay cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal.
  15. Remove ancillary bay probe lid cover from ancillary bay cover.
  16. Verify no high voltage.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering.
  17. Inspect ancillary bay probe lid cover gasket then position onto the ancillary bay cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    Confirm no visual damage present,Wipe ancillary bay with IPA to clean surface,Allow to 1 minute dry time.
  18. Install bolts securing ancillary bay probe lid cover to ancillary bay cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E10 5-Lobe, 6 Nm, Install new fasteners.
  19. Remove HV insulating gloves.
  20. Disconnect HVC logic connector and install logic cap.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 1x cap, Release locking tab then push the handle downward to release connector.
  21. Remove bolts securing ancillary bay cover to HVC.
    Informational PurposesAn informational icon, calling your attention
    참고
    3x bolts, E10, 5 Nm + 30 degrees.
  22. Remove bolts securing ancillary bay cover to HV battery.
    Informational PurposesAn informational icon, calling your attention
    참고
    18x bolts, E10 5-Lobe, 8 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the ancillary bay cover.
  23. Inspect HV insulating gloves.
    Informational PurposesAn informational icon, calling your attention
    참고
    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
  24. Put on HV insulating gloves and leather over gloves.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure to wear Electrical Protective Gloves any time Hioki tester is used.
  25. Remove ancillary bay cover from HV battery.
  26. Inspect ancillary bay for any missing insulators.
    Informational PurposesAn informational icon, calling your attention
    참고
    Install service insulator kit before continuing to next step, The number of bolts on newer vehicles may vary.
  27. Remove AC Filter harness.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 1x clip, 2x bolts, 8mm, 4.5 Nm, Pass harness under PCS hose, Release red locking tab, Discard bolts after removal.

장착

  1. Install AC Filter harness.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 1x clip, 2x bolts, 8mm, 4.5 Nm, Install new bolts, Engage locking tab.
  2. Inspect ancillary bay cover seal to confirm it has no visual damage.
    Informational PurposesAn informational icon, calling your attention
    참고
    Image up close for clarity, Delaminated and torn seals cannot be reused.
  3. Inspect ancillary bay walls for damage.
    Informational PurposesAn informational icon, calling your attention
    참고
    Any dent or depression in the seal that causes it to not be flat will result in a leak, and cannot be reused, Any paint that comes off the ancillary bay wall, whether or not it sticks to the seal, will require enclosure leak test when reassembled, It can still be reused.
  4. Remove service insulator kit.
  5. Position ancillary bay cover to HV battery for installation.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure all accessible insulators are present, wearing Electrical Protective Gloves is not necessary once all HV components are covered.
  6. Remove HV insulating gloves.
  7. Install bolts securing ancillary bay cover to HV battery.
    Informational PurposesAn informational icon, calling your attention
    참고
    18x bolts, E10 5-Lobe, 8 Nm, Use E10 5-Lobe socket without magnet, Fasteners are captive, Follow torque sequence per image.
  8. Install bolts securing ancillary bay cover to HVC.
    Informational PurposesAn informational icon, calling your attention
    참고
    3x bolts, E10, 5 Nm + 30 degrees.
  9. Remove logic cap and connect HVC logic connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated.
  10. Connect 2nd row seat harness and secure cushion.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 2x connectors, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test.
  11. Connect First Responder Loop and LV battery.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
  12. Install rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    참고
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips.
  13. Close hood.
  14. Move RH front seat to original position.
  15. Move LH front seat to original position.
  16. Raise all windows.
  17. Close all four doors.