11/02/2024 07:32:29
Knee Impact Foam - RH (NA) (Remove and Replace)
교정 코드
1405010111
1405010112
참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.
참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오.
참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.
경고
이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.
-
Open LH front door
-
Lower LH front window
-
Move LH front seat backward
-
Open hood
-
Remove rear underhood apron
참고14x clips
-
Power off vehicle from center display
참고Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
-
Disconnect LV battery and First Responder Loop
참고2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
-
Partially release LH front primary door seal
참고Release lower section of LH front primary door seal
-
Remove LH IP end cap
참고5x clips, 2x guide tabs
-
Release LH footwell cover
참고2x magnets,1x guide tab
-
Remove connectors from LH footwell cover
참고1x connector, 1x OBDII connector, Release OBDII connector by depressing tabs from front side
-
Remove LH knee airbag bolt covers
참고2x covers
-
Remove LH knee air bag bolts
참고4x bolts, EP10, 8.5 Nm, Discard bolts after removal
-
Remove LH knee airbag assembly
참고1x connector, Peel back plastic film, Release by pulling back both white tabs simultaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side
-
Remove screws securing IP lower assembly to IP carrier
참고1x screw, T20, 2.3 Nm
-
Remove IP lower assembly from IP carrier
참고13x tabs
-
Remove screws securing IP carrier to cross car beam on lower LH side
참고3x screws, T20, 2.3 Nm, 2x datums
-
Remove screws securing IP carrier to cross car beam at lower center
참고3x screws, T20, 2.3 Nm, 3x datums
-
Remove RH Knee Impact Foam
참고Carefully pull the IP carrier outwards to remove RH Knee Impact Foam
-
Install RH Knee Impact Foam
참고Carefully pull the IP carrier outwards to install RH Knee Impact Foam
-
Install screws securing IP carrier to cross car beam at lower center
참고3x screws, T20, 2.3 Nm, 3x datums
-
Install screws securing IP carrier to cross car beam on lower LH side
참고3x screws, T20, 2.3 Nm, 2x datums
-
Install IP lower assembly to IP
carrier
참고13x tabs
-
Install screws securing IP lower assembly to IP carrier
참고1x screw, T20, 2.3 Nm
-
Install LH knee airbag assembly
참고1x connector, Ensure airbag connector is fully engaged, Apply knee airbag label over squib assembly
-
Install LH knee air bag bolts
참고4x bolts, EP10, 8.5 Nm, Install new bolts
-
Install LH knee airbag bolt covers
참고2x covers
-
Install connectors to LH footwell cover
참고1x connector, 1x OBDII connector, Ensure tabs engage on OBDII connector
-
Install LH footwell cover
참고2x magnets,1x guide tab
-
Install LH IP end cap
참고5x clips, 2x guide tabs
-
Install LH front primary seal
참고Verify seal is seated properly on all trim panels
-
Connect First Responder Loop and LV battery
참고2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
-
Install rear underhood apron
참고14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
-
Close hood
-
Move LH front seat to original position
-
Raise LH front window
-
Close LH front door
