11/02/2024 07:32:33

Engagement Seal - Ancillary Bay (Remove and Replace)

교정 코드 1601010112 FRT 2.88 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

경고

이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

Remove bolts securing LH rocker panel lower cover to body.

참고
4x bolts, 10mm, 5 Nm, Release 4x covers to access bolts, The number of fasteners on newer vehicles may vary.
Remove clips securing the LH rocker panel lower cover to wheel liners.

참고
4x push clips.
Remove LH rocker panel lower cover.

참고
10x clips.
Remove bolts securing RH rocker panel lower cover to body.

참고
4x bolts, 10mm, 5 Nm, Release 4x covers to access bolts, The number of fasteners on newer vehicles may vary.
Remove clips securing the RH rocker panel lower cover to wheel liners.

참고
4x push clips.
Remove RH rocker panel lower cover.

참고
10x clips.
Open all four doors.

참고
If vehicle is being powered down, Latch rear doors to prevent accidental closure.
Lower all four windows.
Move LH front seat backward.
Remove LH front floor mat.
Partially release LH front primary door seal.

참고
Release the lower section of LH front primary door seal.
Remove LH IP end cap.

참고
5x clips, 2x guide tabs.
Remove clip securing LH lower A-pillar assembly.

참고
1x push clip.
Remove LH lower A-pillar assembly.

참고
4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet.
Release LH footwell cover.

참고
5x clips,1x guide tab.
Disconnect LH footwell cover connectors.

참고
2x connectors.
Remove LH console side panel carpet.

참고
11x clips, 2x positioning clips, 1x tab, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Use prytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the tab and pull out the side panel backward, Replace the clips if it is damaged.
Remove LH front main cabin carpet clips.

참고
2x push clips, Number of clips on new vehicles may vary.
Fold the LH front main cabin carpet aside for access.

참고
Dead pedal and foam block are part of carpet,.
Remove LH front footwell HV battery bolts.

참고
2x bolts, EP20, 136 Nm.
Move LH front seat forward.
Move RH front seat backward.
Remove RH front floor mat.
Partially release RH front primary door seal.

참고
Release the lower section of RH front primary door seal.
Remove RH IP end cap.

참고
5x clips, 2x guide tabs.
Remove clip for RH lower A-pillar trim.

참고
1x push clip.
Remove RH lower A-pillar trim.

참고
4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet.
Release RH footwell cover.

참고
2x magnets, 1x guide tab, 1x connector.
Remove connectors from RH footwell cover.

참고
1x puddle light connector, 1x Speaker connector.
Remove RH console side panel carpet.

참고
12x clips, 2x positioning clips, 1x datum, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Useprytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the datum and pull out the side panel backward, Replace the clips if it is damaged.
Remove clips securing RH front main carpet to vehicle.

참고
1x clip, Number of clips on new vehicles may vary.
Fold RH front main cabin carpet aside for access.

참고
2x clips, Lift center piece and pull carpet back, Release seat harness from clips to allow carpet to fold back more.
Remove RH front footwell HV battery bolts.

참고
2x bolts, EP20, 136 Nm.
Move RH front seat forward.
Close RH front door.
Remove 2nd row floor mat from vehicle.
Release 2nd row seat cushion and disconnect harness.

참고
2x clips, 2x connectors, Press tabs backward then pull front edge up.
Pull back rear carpet to access rear interior battery bolts.

참고
2x push clips.
Remove LH rear HV battery interior bolt.

참고
1x bolt, 16mm, 66 Nm, Lift up carpet for access.
Close LH rear door latch manually.
Remove RH rear HV battery interior bolt.

참고
1x bolt, 16mm, 66 Nm, Lift up carpet for access.
Close RH rear door latch manually.
Raise and support vehicle.

참고
Remove body plugs and install M3 lift pad adapters to indicated locations .
Place vehicle in service mode plus.

참고
Using Vehicle Ops mobile app enter last six digits of VIN then select vehicle from list then swipe to the left and select "Enable Service Mode Plus"Vehicle Ops mobile app can be downloaded at: https://mobile.tesla.com/AppStore/Home/AppDetails?appId=6.
Unlock vehicle gateway.

참고
After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information.
Run Thermal Fill Drain (Coolant Only) through the UI.

참고
Select Thermal > Coolant System > Coolant Fill/Drain, click Run, close once routine is completed, Thermal Fill Drain routine has a 5 hour time limit, After 5 hours routine must be performed again.
Open hood.
Remove rear underhood apron.

참고
14x clips.
Power off vehicle from center display.

참고
Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box.
Disconnect LV battery and First Responder Loop.

참고
2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge.
Remove all items from pockets and ensure not wearing metal items.
Verify operation of multimeter.

참고
Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing the 16v battery.
Inspect HV insulating gloves.

참고
Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
Put on HV insulating gloves and leather over gloves.

참고
Make sure to wear Electrical Protective Gloves any time Hioki tester is used.
Remove bolts securing ancillary bay probe lid cover to ancillary bay cover.

참고
2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal.
Remove ancillary bay probe lid cover from ancillary bay cover.
Verify no high voltage.

참고
Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering.
Inspect ancillary bay probe lid cover gasket then position onto the ancillary bay cover.

참고
Confirm no visual damage present,Wipe ancillary bay with IPA to clean surface,Allow to 1 minute dry time.
Install bolts securing ancillary bay probe lid cover to ancillary bay cover.

참고
2x bolts, E10 5-Lobe, 6 Nm, Install new fasteners.
Remove fastener securing busbar cover access door.

참고
1x bolt, 10mm, 9 Nm.
Remove bolts securing charge port busbar kit to HV header.

참고
2x bolts, 10mm, 9 Nm.
Lift busbar kit connector to remove from HV header.

참고
4x guide tabs, Ease removal of aluminum connector housing by shifting rear end of busbar assembly upward.
Remove HV insulating gloves.
Disconnect HVC logic connector and install logic cap.

참고
1x connector, 1x cap, Release locking tab then push the handle downward to release connector.
Remove bolt securing DCDC ground busbar to body.

참고
1x bolt, 12mm, 20 Nm.
Remove nut securing DCDC ground busbar to HV battery.

참고
1x nyloc nut, 13mm, 9 Nm, Discard nut after removal.
Remove DCDC ground busbar.
Remove nut securing positive LV output from PCS cable and move cable aside.

참고
1x nut, 13mm, 15 Nm, Discard after removal.
Raise vehicle fully and lower lift onto locks.

참고
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects.
Remove LH and RH clips securing rear aero shield to wheel house liner.

참고
2x clips.
Remove rear aero shield.

참고
11x bolts, 10mm, 5 Nm.
Remove outer fasteners securing front aero shield.

참고
7x bolts, 10mm, 5 Nm.
Remove remaining nuts and remove front aero shield from vehicle.

참고
2x nuts, 15mm, 5 Nm.
Remove push clips securing lower rear edge of LH front wheel liner to vehicle for access to coolant hose.

참고
3x push clips.
Remove bolt securing LH front wheel liner to skid plate.

참고
1x bolt, 10mm, 5 Nm.
Use bungee strap to pull back LH front wheel liner.

참고
Secure to subframe.
Position coolant drain container underneath LH front of HV battery.
Attach hose extension to coolant drain hose for extra length.
Connect battery flush fitting adapter to coolant cart drain hose.
Disconnect HV battery return hose at LH side of vehicle and connect battery flush fitting to male side.

참고
1x spring clip.
Attach battery drain fitting adapter to female side of HV battery return tube.

참고
1x spring clip, Make sure valve is set to closed, Perform push-pull test to verify adapter is fully engaged.
Attach battery drain fitting adapter to coolant cart pressure hose.
Open valve on battery drain fitting adapter.

참고
Turn valve knob to vertical position.
Slowly open valve on pressure regulator and allow coolant to drain out of HV battery return tube.

참고
Close valve on pressure regulator once no coolant is draining from HV battery return hose.
Close valve on pressure regulator once no coolant is draining from battery return hose.
Disconnect compressed air from coolant cart.
Remove battery drain fitting adapter from female side of HV battery return tube.

참고
1x spring clip, Set valve knob to closed position.
Remove battery flush fitting adapter from male side of HV battery return tube.

참고
1x spring clip, Plug hose once adapter has been removed.
Remove bolt securing RH front wheel liner to skid plate.

참고
1x bolt, 10mm, 5 Nm.
Remove push clips securing lower rear edge of RH front wheel liner to vehicle for access to coolant hose.

참고
3x push clips.
Use bungee strap to pull back RH front wheel liner.

참고
Secure to subframe.
Position coolant drain container underneath RH front of HV battery.
Disconnect powertrain supply hose from powertrain supply tube.

참고
1x spring clips, Plug hoses as required.
Disconnect powertrain return hose from powertrain return tube.

참고
1x spring clip, Plug hoses as required.
Disconnect HV battery manifold hose.

참고
1x spring clip, 2x plugs, Plug hoses as required.
Remove bolts securing front skid plate.

참고
4x bolts, EP10, 13 Nm.
Remove skid plate from HV battery.
Remove manifold tube from front of HV battery.

참고
4x spring clips, Plug HV battery.
Disconnect A/C compressor HV harness connector.

참고
1x connector, 1x Red locking tab, 2 stage push release, Unlock by pulling back red tab, Push orange lip and pull back ''stage 1'', Push green lip and pull back to disconnect.
Release LH side hose clip from rear battery skid plate enclosure.

참고
1x fir tree clip.
Release RH side hose clips from rear battery skid plate enclosure.

참고
2x fir tree clips.
Remove lower bolts securing HV battery rear skid plate enclosure .

참고
2x bolts, EP10, 13 Nm, Older vins may be equipped with additional fastener count.
Remove upper nut securing HV battery rear skid plate enclosure .

참고
1x nut, 10mm, 13 Nm, Fastener count may vary on older built vehicles.
Remove upper bolts securing HV battery rear skid plate enclosure .

참고
4x bolts, 13mm, 35 Nm.
Remove HV battery rear skid plate enclosure .
Position coolant drain container underneath LH rear of HV battery.
Disconnect LH coolant hose from rear of HV battery.

참고
1x spring clip, 2x plugs, Plug both the coolant hose and passthrough .
Remove fir tree clip securing coolant hose to rear subframe shear plate.

참고
1x fir tree clip.
Disconnect RDU inverter inlet tube from LH rear of HV battery.

참고
1x spring clip, Plug hose connections as needed, Coolant loss greater than 1 L will require vacuum fill.
Attach coolant drain hose adapter to PCS outlet hose coupling.

참고
Use adapter with 90 degree angle, Make sure locking tab is fully seated.
Attach coolant drain hose adapter to coolant hose extension.
Attach coolant hose extension to coolant drain hose.

참고
Use caution as coolant may spill, Make sure to wear safety glasses.
Position coolant drain container underneath RH rear of vehicle.
Disconnect rear PT supply hose from rear of HV battery.

참고
1x spring clip, Plug hose connections as needed, Coolant loss greater than 1 L will require vacuum fill.
Attach coolant pressure tester to PCS inlet hose coupling.

참고
This adapter connected to regulated air line adapter, Make sure the locking tab is fully seated.
Attach coolant pressure tester to pressure fitting adapter.
Connect compressed air to coolant pressure tester.
Open regulator valve then slowly adjust regulator to 50 psi.

참고
Use caution as coolant may spill, Make sure to wear safety glasses.
Open 2nd valve slowly.

참고
Use caution as coolant may spill, Make sure to wear safety glasses.
Set timer for 1 minutes and select start.

참고
Once timer is complete, select Stop Reset.
Close regulator valve.
Disconnect compressed air from coolant pressure tester.
Remove coolant pressure tester from PCS inlet hose coupling.
Position coolant drain container underneath LH rear of HV battery.
Remove coolant drain adapter with hose from PCS outlet hose coupling.

참고
1x spring clip.
Disconnect RDU outlet hose from PT return tube and plug both hose ends.

참고
1x spring clip, 2x plugs, Lower hose located at RH rear of HV battery, Use shop towel to clean any residue coolant if necessary, Coolant loss greater than 1 L will require vacuum fill.
Support front portion of rear subframe.
Release clips securing coolant hoses to LH shear plate.

참고
2x fir tree clips.
Remove smaller fasteners securing LH shear plate.

참고
2x bolts, 13mm, 35 Nm.
Remove large bolt securing LH shear plate and subframe to body and remove shear plate.

참고
1x bolt, 21mm, 130 Nm, Discard after removal.
Hand tighten bolt securing LH side of subframe to body.

참고
1x bolt, 21mm, 130 Nm.
Release clips securing coolant hoses to RH shear plate.

참고
2x fir tree clips.
Remove smaller fasteners for RH shear plate.

참고
2x bolts, 13mm, 35 Nm.
Remove large bolt securing RH shear plate and subframe to body and remove shear plate.

참고
1x bolt, 21mm, 130 Nm, Discard at later step.
Hand tighten bolt securing RH side of subframe to body.

참고
1x bolt, 21mm, 130 Nm.
Remove support stand from under vehicle.
Remove nut securing RDU HV cable bracket to HV battery.

참고
1x nut, 10mm, 10 Nm, Number of fasteners may vary.
Disconnect RDU HV cable from HV battery.

참고
1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged.
Place HV battery table into position and lower vehicle to support HV battery.

참고
Recommend assistance, Line up table so center 4 bolts are accessible through opening in table, Adjust final battery table position using adjustable caster jacks on table.
Remove central bolts securing HV battery center ski cover.

참고
4x bolts, EP14, 34 Nm.
Remove bolts securing LH front support bracket to vehicle.

참고
4x bolts, 16mm, 110 Nm.
Remove bolts securing RH front support bracket to vehicle.

참고
4x bolts, 16mm, 110 Nm.
Remove LH bolts securing HV battery to vehicle.

참고
8x bolts, 13mm, 35 Nm.
Remove RH bolts securing HV battery to vehicle.

참고
8x bolts, 13mm, 35 Nm.
Raise vehicle free of HV battery.

참고
Recommend assistance.
Remove battery from under vehicle.

참고
Recommend assistance.
Remove ancillary bay engagement seal from HV battery pack.

참고
Discard anytime HV battery is removed from vehicle.

장착

Install ancillary bay engagement seal onto HV battery pack.

참고
This seal is a one time use item and should be replaced each time a HV battery pack is removed from vehicle or installed onto a new HV battery pack if not equipped.
Install HV battery alignment rods.

참고
2x rods, To body at front of vehicle, 2x rods, To battery near ancillary bay.
Position HV battery under vehicle.

참고
Recommend assistance.
Lower vehicle onto HV battery and align holes.

참고
Recommend assistance, Use alignment rods, Be sure coolant hoses do not get caught on alignment rods, Caution not to damage HV cable, Do not fully lower vehicle onto battery (this will help with installing battery bolts).
Set RH bolts securing HV battery to vehicle with cordless impact.

참고
8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
Set LH bolts securing HV battery to vehicle with cordless impact.

참고
8x bolts, 13mm, 35 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
Remove HV battery alignment rods.

참고
2x rods, To body at front of vehicle, 2x rods, To battery near ancillary bay.
Set bolts securing RH front support bracket to vehicle with cordless impact.

참고
4x bolts, 16mm, 110 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
Set bolts securing LH front support bracket to vehicle with cordless impact.

참고
4x bolts, 16mm, 110 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
Set central bolts securing HV battery center ski cover with cordless impact.

참고
4x bolts, EP14, 34 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
Install bolts securing HV battery to body at LH shear plate area hand tight.

참고
2x bolts, 13mm, 35 Nm, Torque at later step.
Install bolts securing HV battery to body at RH shear plate area hand tight.

참고
2x bolts, 13mm, 35 Nm, Torque at later step.
Connect RDU HV cable to HV battery.

참고
1x connector, Make sure the connector lock is 90 degrees from the connector before beginning to secure the connector, Use one hand to support the connector while other latching locking tab. Once installed, verify that the latch is not damaged and fully secured in the latched position.
Install nut securing RDU HV cable bracket to HV battery.

참고
1x nut, 10mm, 10 Nm, Number of fasteners may vary.
Remove hose plugs and connect RDU outlet hose to PT return tube.

참고
1x spring clip, 2x plugs, Perform push-pull-push test to make sure hose is fully engaged, Use shop towel to clean any coolant residue if necessary, Loss of coolant greater than 1L requires coolant vacuum fill.
Remove plugs and connect RDU inverter inlet hose to LH rear of HV battery.

참고
1x spring clip, Perform push-pull-push test to make sure hose is fully engaged.Loss of coolant greater than 1L requires coolant vacuum fill.
Position HV battery rear skid plate enclosure onto HV battery for installation.

참고
Recommend assistance if needed.
Install upper bolts securing HV battery rear skid plate enclosure hand tight.

참고
4x bolts, 13mm, 35 Nm, Torque at later step.
Install upper nut securing HV battery rear skid plate enclosure hand tight.

참고
1x nut, 10mm, 13 Nm, Torque at later step.
Install lower bolts securing HV battery rear skid plate enclosure .

참고
2x bolts, EP10, 13 Nm, Earlier vins may be equipped with additional bolts.
Lower vehicle onto pack completely.

참고
Recommend assistance.
Torque RH bolts securing HV battery to vehicle.

참고
8x bolts, 13mm, 35 Nm.
Torque LH bolts securing HV battery to vehicle.

참고
8x bolts, 13mm, 35 Nm.
Torque bolts securing RH front support bracket to vehicle.

참고
4x bolts, 16mm, 110 Nm.
Torque bolts securing LH front support bracket to vehicle.

참고
4x bolts, 16mm, 110 Nm.
Torque central bolts securing HV battery center ski cover.

참고
4x bolts, EP14, 34 Nm.
Torque bolts securing HV battery rear skid plate enclosure to vehicle.

참고
4x bolts, 13mm, 35 Nm.
Torque upper nut securing HV battery rear skid plate enclosure .

참고
1x nut, 10mm, 13 Nm.
Torque lower bolts securing rear battery enclosure skid plate.

참고
2x bolts, EP10, 13 Nm, Earlier vins may be equipped with additional bolts.
Install RH side hose clips to HV battery rear skid plate enclosure .

참고
2x fir tree clips.
Install LH side hose clip to HV battery rear skid plate enclosure .

참고
2x clips, Clip quantity may vary on older vehicles.
Raise vehicle and lower onto locks, then remove battery table from under vehicle.

참고
Recommend assistance, Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
Support front portion of rear subframe.
Remove smaller fasteners for LH shear plate.

참고
2x bolt, 13mm, 35 Nm.
Remove smaller fasteners for RH shear plate.

참고
2x bolt, 13mm, 35 Nm.
Install LH front bolt and shear plate to rear subframe hand tight.

참고
1x bolt, 21mm, 130 Nm, Install new bolt, Torque at later step.
Install bolts securing LH shear plate to HV battery hand tight.

참고
2x bolts, 13mm, 35 Nm.
Install RH front bolt and shear plate to rear subframe hand tight.

참고
1x bolt, 21mm, 130 Nm, Install new bolt, Torque at later step.
Install bolts securing RH shear plate to HV battery hand tight.

참고
2x bolts, 13mm, 35 Nm.
Torque bolts securing shear plates to vehicle.

참고
4x bolts, 13mm, 35 Nm.
Torque bolt securing subframe and LH shear plate to body.

참고
1x front bolt, 21mm, 130 Nm, Mark bolt after torque.
Torque bolt securing subframe and RH shear plate to body.

참고
1x front bolt, 21mm, 130 Nm, Mark bolt after torque.
Remove support stand from under vehicle.
Install clips securing coolant hoses to RH shear plate.

참고
2x fir tree clips.
Install clips securing coolant hoses to LH shear plate.

참고
2x fir tree clips.
lnstall rear aero shield.

참고
11x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts.
Install LH and RH clips securing rear aero shield to wheel house liner.

참고
2x clips.
Connect HV battery manifold hose.

참고
1x spring clip, Remove plugs.
Connect PT supply hose.

참고
1x spring clip, Remove plugs, Perform push-pull-push test to make sure hose is fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill.
Connect PT return hose.

참고
1x spring clip, Remove plugs, Perform push-pull test to verify hoses are fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill.
Install front skid plate.

참고
4x bolts, EP10, 13 Nm, 2x tabs, Position and move backward to installation.
Release RH front wheel liner from bungee strap.

참고
Remove strap from vehicle.
Install bolt securing RH front wheel liner to skid plate.

참고
1x bolt, 10mm, 5 Nm.
Connect HV battery return hose.

참고
1x spring clip.
Release LH front wheel liner from bungee strap.

참고
Remove strap from vehicle.
Install bolt securing LH front wheel liner to skid plate.

참고
1x bolt, 10mm, 5 Nm.
Connect A/C compressor HV harness connector.

참고
1x connector, Engage locking tab.
Position front aero shield onto vehicle.

참고
2x nuts, 15mm, 5 Nm, Hand-tighten the nuts to temporarily hold the panel in place.
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield.

참고
7x bolts, 10mm, 5 Nm.
Lower vehicle fully.

참고
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
Remove coolant bottle cap.
Place empty coolant container into front storage area.
Fill container with at least 15L of coolant.
Place filled coolant container into front storage area.
Install refill tool cap onto coolant bottle assembly.
Setup vacuum refill tool.

참고
Verify all valves on refill tool are in the closed position, See image for clarity.
Install vacuum refill hose into refill cap on coolant bottle.

참고
Perform push-pull-push test to verify hose is fully engaged.
Position overflow hose into empty container.
Place refill hose inside filled coolant container .

참고
Make sure hose end is fully submerged into coolant.
Connect shop air supply to coolant refill tool.

참고
If not already done, Verify refill valve is set to off.
Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close valve.

참고
Gauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed.
Slowly open coolant refill valve to allow coolant to be drawn into coolant refill hose, Close valve when hose is full of coolant.

참고
This purges trapped air from the hose.
Monitor gauge for 30 seconds to verify a vacuum is maintained in cooling system.
Reopen the air inlet valve for 3 minutes to continue evacuating cooling system, then close valve.
Slowly open refill valve to allow coolant to be drawn into system.

참고
Make sure hose end of refill hose is fully submerged during entire process.
Once gauge reads zero, close refill valve.
Disconnect shop air supply from coolant refill tool.
Remove coolant refill hose from coolant container.
Remove coolant overflow hose from coolant container.
Remove vacuum refill hose from refill cap on coolant bottle.
Remove coolant refill tool from vehicle.
Remove both coolant containers from inside underhood area.
Position busbar kit connector and lower onto HV header.

참고
4x guide tabs, Shift rear end of busbar assembly upward to help ease installation, If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary.
Install bolts securing charge port busbar kit to HV header.

참고
2x bolts, 10mm, 9 Nm.
Install fastener securing busbar cover access door.

참고
1x bolt, 10mm, 9 Nm.
Install DCDC ground busbar.

참고
Slotted hole goes to body side.
Install bolt securing DCDC ground busbar to body.

참고
1x bolt, 12mm, 20 Nm.
Install nut securing DCDC ground busbar to HV battery.

참고
1x nyloc nut, 13mm, 9 Nm, Install new nyloc nut.
Connect DCDC positive cable to right body harness.

참고
1x connector,1x clip Connect the connector and push in the red locking tab.
Remove logic cap and connect HVC logic connector.

참고
1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated.
Connect First Responder Loop and LV battery.

참고
2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
Remove lift arms from below vehicle.

참고
Lower rack arms fully and remove them from under vehicle.
Move vehicle away from lift.

참고
Position to allow easy access to interior.
Select "Stop Thermal Fill Drain" through UI.

참고
Allow routine to complete, ensure routine is successful.
Inspect coolant level and top off as necessary.

참고
Ensure that fluid level is at Max line.
Select "Start Coolant Air Purge" using the UI.

참고
냉각수 펌프 작동이 멈출 때까지 기다립니다(소음 발생). 루틴이 통과된 것으로 표시되지만 펌프는 10분 동안 작동합니다. 이 시간 동안 다음 루틴을 시작하면 실패합니다. 차량이 "주행" 상태가 아닌지 확인하십시오. 루틴 완료 메시지에도 루틴이 계속해서 실행됩니다. 공회전 속도 = ~1500RPM, 테스트 속도는 3500~6500RPM 사이에서 다르며 액추에이터 밸브는 SERIES와 PARALLEL 간에 전환됩니다. 차량을 "주행" 상태로 전환하면 이 루틴이 중지됩니다. 속도가 7000RPM 이상인 경우 펌프가 에어록인 것을 의미합니다. 냉각수 수위가 보틀의 NOM과 MAX 선 사이에 도달하도록 계속해서 냉각수를 추가하고 배출합니다.
Install RH rear HV battery interior bolt.

참고
1x bolt, 16mm, 66 Nm, Lift up carpet for access.
Install LH rear HV battery interior bolt.

참고
1x bolt, 16mm, 66 Nm, Lift up carpet for access.
Install rear carpet section.

참고
2x push clips, Tuck corners under lower C pillar trim.
Connect 2nd row seat harness and secure cushion.

참고
2x clips, 2x connectors, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test.
Close LH rear door.

참고
Release latch before closing if manually latched.
Close RH rear door.

참고
Release latch before closing if manually latched.
Open LH front door.
Install LH front footwell HV battery bolts.

참고
2x bolts, EP20, 136 Nm.
Install LH front main cabin carpet to vehicle.

참고
2x push clips, Number of clips on new vehicles may vary.
Install LH console side panel carpet.

참고
11x clips, 2x positioning clips, 1x tab, Position side panel and align the front tab, Push the console panel from the front towards the rear.
Install connectors to LH footwell cover .

참고
1x connector, 1x OBDII connector, Ensure tabs engage on OBDII connector.
Install LH footwell cover.

참고
2x magnets,1x guide tab.
Install LH lower A-pillar assembly.

참고
4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim.
Install clip securing LH lower A-pillar assembly.

참고
1x push clip.
Install LH IP end cap.

참고
5x clips, 2x guide tabs.
Install LH front primary seal.

참고
Verify seal is seated properly on all trim panels.
Install LH front floor mat.
Open RH front door.
Install RH front footwell HV battery bolts.

참고
2x bolts, EP20, 136 Nm.
Unfold RH front main cabin carpet back to original position.

참고
1x clip.
Install RH console side panel carpet.

참고
12x clips, 2x positioning clips, 1x datum, Position side panel and align the front datum, Push the console panel from the front towards the rear.
Install RH footwell cover .

참고
2x magnets, 1x guide tab, 1x connector.
Install RH lower A-pillar trim.

참고
4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim.
Install clip for RH lower A-pillar trim.

참고
1x push clip.
Install RH IP end cap.

참고
5x clips, 2x guide tabs.
lnstall seat lower section of RH front primary seal.

참고
Verify seal is seated properly on all trim panels.
Install RH front floor mat.
Close RH front door.
Inspect coolant level and top off as necessary.

참고
Ensure that fluid level is at Max line.
Install coolant bottle cap.
Install frunk assembly to vehicle.

참고
4x clips, Replace any clips if broken or missing.
Install bolts securing frunk assembly.

참고
6x bolts, 10mm, 5 Nm.
Install frunk service panel.

참고
3x clips, Push towards rear of vehicle to secure.
Install access panel to frunk assembly.

참고
3x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push forward to secure clips.
Install fresh air gutter assembly.

참고
3x clips.
Install rear underhood apron.

참고
14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips.
Close hood.
Install LH rocker panel lower cover into position.

참고
10x clips.
Install bolts securing LH rocker panel lower cover to body.

참고
4x bolts, 10mm, 5 Nm, Secure 4x covers, The number of fasteners on newer vehicles may vary.
Install clips securing the LH rocker panel lower cover to wheel liners.

참고
4x push clips.
Install RH rocker panel lower cover into position.

참고
10x clips.
Install bolts securing RH rocker panel lower cover to body.

참고
4x bolts, 10mm, 5 Nm, Secure 4x covers, The number of fasteners on newer vehicles may vary.
Install clips securing the RH rocker panel lower cover to wheel liners.

참고
4x push clips.
Exit Service Mode through UI.

참고
Exit Service Mode: Controls > Service Mode > Exit Service Mode, Press and hold to exit.
Raise all windows.
Close LH front door.