2025-09-23

Brake Line Assembly - Side Sill (Remove and Replace)

교정 코드 3303010032 3.66 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-08-18: Released new procedure.

탈거

  1. Remove the front and rear wheels. See 휠 어셈블리(탈거 및 장착).
  2. Remove the HV battery. See HV Battery (RWD) (Remove and Replace) or HV Battery (AWD) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not follow the steps to discharge the HV battery outlined in the referenced procedures.
  3. Position an oil drain container under the LH front brake line area.
  4. Remove the LH front wheel arch liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  5. Remove the top and bottom side sill brake line tube nuts from the front brake pipe junction block.
  6. Remove the clip from the LH front junction block.
  7. Release the brake lines from the LH front junction block.
  8. Remove the LH rear wheel arch liner. See Wheel Arch Liner - Rear - LH (Remove and Replace).
  9. Place an oil drain container under the rear brake line junction box.
  10. Remove the LH and RH rear brake line tube nuts from the rear brake pipe junction block.
  11. Remove the clip from the LH rear junction block.
  12. Remove nut that attaches the LH rear junction block to the vehicle.
  13. Remove the LH rear junction block from the vehicle.
  14. Remove the clips that attache the side sill brake pipe assembly to the body.
  15. Remove the side sill brake pipe assembly.

  1. Position the side sill brake pipe assembly to the vehicle for installation.
  2. Install the clips (x4) that attach the side sill brake pipe assembly to the vehicle.
  3. Install the LH rear junction block to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Put the LH and RH rear brake pipes in the connector.
  4. Install the nut that attaches the LH rear junction block to the vehicle.
  5. Install the black clip that attaches the brake lines at the LH rear junction block.
  6. Install the LH and RH rear brake line tube nuts to the LH rear brake pipe junction block.
  7. Install the LH rear wheel arch liner. See Wheel Arch Liner - Rear - LH (Remove and Replace).
  8. Install the brake lines into the LH front junction block.
  9. Install the clip that attaches the brake lines at LH front junction block.
  10. Install the side sill brake line tube nuts to the LH front brake pipe junction block.
  11. Install the LH front wheel arch liner. See Wheel Arch Liner - Front - LH (Remove and Replace).
  12. Install a new penthouse engagement seal onto the HV battery pack.
    Informational PurposesAn informational icon, calling your attention
    참고
    This seal is a one time use item and should be replaced each time a HV battery pack is removed from the vehicle.
  13. Install the HV battery. See HV Battery (RWD) (Remove and Replace) or HV Battery (AWD) (Remove and Replace).
  14. Install the LH front and rear wheel arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
  15. Install the front and rear wheels. See 휠 어셈블리(탈거 및 장착).