05/12/2023 10:14:33

Hose - Powertrain Supply (Remove and Replace)

교정 코드 1830020112 FRT 0.72 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

  • 1080568-00-A Fluid Catcher
  • 1135762-00-A 키트, 서비스 플러그, 냉각 호스, Model 3
  • 1065131-00-A Kit, Battery Coolant Drain
표 1. 토크 규격: Hose - Powertrain Supply (Remove and Replace)
설명 토크 값 권장 공구 재사용/교체 참고
RH 전면 휠 라이너를 스키드 플레이트에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 무선 1/4인치 Dr 래칫
  • 너트세터 1/4인치 드라이브 6인치 X 10mm 마그네틱 딥
  • 10mm 딥소켓
  • 래칫/토크 렌치
 재사용

탈거

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Disconnect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Raise the vehicle fully and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  5. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the bolt that secures the RH front wheel liner to the skid plate.
    팁: 다음 공구 사용을 권장합니다.
    • 무선 1/4인치 Dr 래칫
    • 너트세터 1/4인치 드라이브 6인치 X 10mm 마그네틱 딥
    • 10mm 딥소켓
    • 래칫/토크 렌치
  7. Remove the push clips (x3) that secure the lower rear edge of the RH front wheel liner to the vehicle for access to the coolant hose.
  8. Use a bungee strap to pull back the RH front wheel liner and secure it to the subframe.
  9. Position the coolant drain container underneath the RH front of the HV battery.
  10. Release the spring clip and the plugs (x2) to disconnect the powertrain supply hose from the powertrain supply tube, and then plug the ends of both fittings as soon as possible to avoid coolant loss.
    Informational PurposesAn informational icon, calling your attention
    참고
    Coolant loss greater than 1L requires vacuum fill.
  11. Release the powertrain supply hose clips (x2) from the vehicle.
  12. Remove the coolant drain container from underneath the vehicle.
  13. Lower the vehicle to a comfortable working height and set the lift onto locks.
  14. Position the fluid catcher underneath the front of the vehicle.
  15. Remove the fresh intake duct. See Fresh Air Intake - HVAC (Remove and Replace).
  16. Pull the red locking tab to disengage the lock, and then hold and pull it again to release the electrical connector, so that the powertrain supply hose sensor is disconnected.
  17. Release the spring clip and the plugs (x2) to disconnect the powertrain supply hose from the supermanifold, and then plug the ends of both fittings as soon as possible to avoid coolant loss.
    Informational PurposesAn informational icon, calling your attention
    참고
    Coolant loss greater than 1L requires vacuum fill.
  18. Remove the powertrain supply hose from the vehicle.

장착

  1. Install the powertrain supply hose to the vehicle and place a coolant plug on the lower end of the hose to avoid coolant loss.
  2. Remove the plugs on the ends of fittings as quickly as possible to avoid coolant loss, and then secure the spring clip and the plug to connect the powertrain supply hose to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull-push test to make sure that the hose is fully secured.
  3. Engage the locking tab to connect the powertrain supply hose sensor.
    Informational PurposesAn informational icon, calling your attention
    참고
    The harness and the coolant hose are color coded. Match the color of the harness to the color of the coolant hose.
  4. Install the fresh intake duct. See Fresh Air Intake - HVAC (Remove and Replace).
  5. Remove the fluid catcher from underneath the vehicle.
  6. Raise the vehicle fully and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  7. Position the coolant drain container underneath the RH front of the HV battery.
  8. Remove the plugs on the ends of fittings as quickly as possible to avoid coolant loss, and then secure the spring clip and the plugs (x2) to connect the powertrain supply hose to the powertrain supply tube.
    Informational PurposesAn informational icon, calling your attention
    참고

    Perform a push-pull-push test to make sure that the hose is fully secured.

    Coolant loss greater than 1L requires vacuum fill.

  9. Secure the powertrain supply hose clips (x2) to the vehicle.
  10. Remove the coolant drain container from underneath the vehicle.
  11. Release the RH front wheel liner from the bungee strap, and remove the strap from the vehicle.
  12. Install the push clips (x3) that secure the lower rear edge of the RH front wheel liner to the vehicle.
  13. Install the bolt that secures the RH front wheel liner to the skid plate.
    5 Nm (3.7 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 무선 1/4인치 Dr 래칫
    • 너트세터 1/4인치 드라이브 6인치 X 10mm 마그네틱 딥
    • 10mm 딥소켓
    • 래칫/토크 렌치
  14. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  15. Lower the vehicle fully.
  16. Connect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  17. Remove the coolant bottle cap and fill the coolant to the "MAX" line.
  18. Unlock the vehicle gateway. See 게이트웨이 잠금 해제.
  19. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Coolant System > Coolant Purge > Run to start the coolant air purge.
    Informational PurposesAn informational icon, calling your attention
    참고
    • The routine will last for a while after the stop message displays. The coolant pumps are audible.
    • The test lasts for approximately 10 mins. Do not start another routine during this time.
    • Make sure that the vehicle is not in Drive. Putting the vehicle into Drive will stop this routine.
    • The speed in the test varies from 3500-6500 RPM (idle speed = ~1500 RPM) and the actuated valve varies between SERIES and PARALLEL.
    • 속도가 7000RPM 전후에 있는 경우 펌프가 에어록 상태임을 나타냅니다. 진공 충전을 다시 수행하십시오. 냉각수 수위가 보틀의 NOM과 MAX 선 사이에 도달하도록 계속해서 냉각수를 추가하고 배출합니다.
  20. Inspect the coolant level, top off as necessary, and then install the coolant bottle cap.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure that the coolant level is at the "Max" line.
  21. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  22. Raise the LH front window and close the LH front door.
  23. Remove the lift arms from below the vehicle.