교정 코드 NEW 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. 적재함 커버를 엽니다.
2. 테일게이트를 엽니다.
3. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
4. 전동식 프렁크를 엽니다.
5. Use the vehicle touchscreen to open charge port door.
6. MV 전원을 연결 해제합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
7. Verify operation of multimeter
   참고

   Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals

   

   

8. Remove all items from pockets and ensure not wearing metal items
   참고

   This includes phones, badges, metal belt buckles airpods and headphones

   

9. Inspect HV insulating gloves
   참고

   Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.

   

10. Put on HV insulating gloves and leather over gloves
    참고

    Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration

    

11. Verify there is no high voltage present at the charge port
    참고

    Measure B+ to B-, and B+ to Ground and B - to Ground, Place Alligator clip onto body panel

    

    

    

    

12. Remove leather over gloves and HV insulating gloves
13. Remove the LH rear fore fender flare. See Fender Flare - Fore - Rear - LH (Remove and Install).
14. Remove the LH rear aft fender flare. Se Fender Flare - Aft - Rear - LH (Remove and Install).
15. Remove the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
16. Remove the LH rear fore fender flare carrier. See Carrier - Fender Flare - Fore - Rear - LH (Remove and Install).
17. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
18. Remove the LH sail applique. See Sail Applique - LH (Remove and Install) (Post 11/4/2024).
19. Remove the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install).
20. Remove the LH upper bed side wall. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
21. Remove the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
22. Remove the LH lower bed side wall. See Bed Side Wall - LH (Standard) (Remove and Install).
23. Remove the bolt that attaches the busbar HV connector lid.
    

    9 Nm (6.6 lbs-ft)
    참고

    EP10

    

24. Remove the bolts (x2) that attach the HV connector to the DC FC header.
    

    9 Nm (6.6 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

25. Release the HV connector from the DC FC header, and then use an inflatable airbag to suspend the busbar assembly above the ancillary assembly.

    

26. Disconnect the charge port assembly electrical connector.
    참고

    Remove the white locking tab. Press the tab to release the connection from the charge port. Continue to pull off connector. The charge port connection is intended to disengage the safety cap when released.

    참고

    Do not push down on the red tab. Pull the red tab to disengage lock. Pull again to release the electrical connector.

    

27. Release the clip and disconnect the charge port door LV electrical connectors (x2).

    

28. Remove the bolt that attaches the ground cable to the busbar assembly.
    

    6.5 Nm (4.8 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

29. Remove the bolt that attaches the charge port to the outer sail.
    

    6.5 Nm (4.8 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 딥소켓

    

30. Remove the bolts (x2) that attach the charge port assembly onto the body.
    

    6 Nm (4.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 12 포인트 딥소켓
    경고

    Use only hand tools. Risk of galling if power tools are used on stainless bolts.

    

31. Remove the charge port and busbar assembly from the vehicle.

    

    

32. Clean the DC FC header contact surface of residual Penetrox with an Isopropyl Alcohol (IPA) wipe.
    참고

    Allow 1 minute dry time after removing Penetrox.

    

33. Clean the busbar HV connector contact surface of residual Penetrox.
    참고

    Allow 1 minute dry time after removing Penetrox.

    참고

    It is necessary to clean the HV connector during reuse of the busbar.

    

34. Apply Penetrox onto the HV connector joints.
    참고

    Apply 2 drops of Penetrox A-13 about 5 mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered.

    

35. Position the charge port busbar assembly onto the vehicle.

    

    

36. Install the bolts (x2) that attach the charge port busbar kit to the HV header.
    

    9 Nm (6.6 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓 (insulated)

    

37. Perform a Hioki resistance test at each HV joint from the HV busbar lead to the bolt head.
    참고

    x2 HV joints

    참고

    When using a Hioki tester, verify the meter has been properly adjusted and set prior to usage.

    참고

    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).

    • If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
    • If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.
    • If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki test passed. proceed to the next step.

    

    

38. Install the bolt that attaches the busbar HV connector lid.
    

    9 Nm (6.6 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

39. Install the bolts (x2) that attach the charge port assembly onto the body.
    

    6 Nm (4.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 12 포인트 딥소켓
    경고

    Use only hand tools. Risk of galling if power tools are used on stainless bolts.

    

40. Install the bolt that attaches the charge port to the outer sail.
    

    6.5 Nm (4.8 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 딥소켓

    

41. Install the bolt that attaches the busbar ground to the body.
    

    6.5 Nm (4.8 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

42. Connect the charge port door electrical connectors (x2) and fasten clip.

    

43. Connect the charge port electrical connector.
    참고

    Fully engage the connection and white locking tab. The electrical connector is intended to lock the safety cap in place.

    

44. Install the LH lower bed side wall. See Bed Side Wall - LH (Standard) (Remove and Install).
45. Install the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
46. Install the LH upper bed side wall. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
47. Install the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install).
48. Install the LH sail applique. See Sail Applique - LH (Remove and Install) (Post 11/4/2024).
49. Install the LH rear fore fender flare carrier. See Carrier - Fender Flare - Fore - Rear - LH (Remove and Install).
50. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
51. Install the LH rear aft fender flare carrier. See Carrier - Fender Flare - Aft - Rear - LH (Remove and Install).
52. Install the LH rear fore fender flare. See Fender Flare - Fore - Rear - LH (Remove and Install).
53. Install the LH rear aft fender flare. See Fender Flare - Aft - Rear - LH (Remove and Install).
54. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
55. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
56. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.
57. 적재함 커버를 닫습니다.
58. 테일게이트를 닫습니다.