2026-03-30

Terrestrial Armor (Remove and Install)

교정 코드 1601070091 1.74 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-03-19: Cleaned up entire procedure.
  • 2026-03-16: Released new procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

탈거

  1. LH 전면 도어를 엽니다.
  2. LH 전면 창문을 내립니다.
  3. 터치스크린에서 컨트롤 > 서스펜션 > 매우 높음을 터치하여 차량 지상고를 매우 높음으로 설정합니다.
  4. 터치스크린에서 컨트롤 > 차량 정비 > 잭 모드를 터치하여 잭 모드를 활성화합니다.
  5. Partially release the clips (x11) that attach the rear of the LH front fender flare cover to the vehicle, and then disconnect the electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    It is not necessary to fully remove the LH front fender flare cover.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Plastic Trim Tool
    그림 1. LH shown; RH similar
  6. Release the clip that attaches the LH rocker cover to the LH front wheel liner.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 클립 프라이툴
    그림 2. LH shown; RH similar
  7. Partially release the clips (x13) that attach the front of the LH rear fender flare cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    It is not necessary to fully remove the LH rear fender flare cover.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Plastic Trim Tool
    그림 3. LH shown; RH similar
  8. Remove the clip that attaches the LH rocker cover to the LH rear wheel liner.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 클립 프라이툴
    그림 4. LH shown; RH similar
  9. Remove the bolts (x2) and release clips (x13) that attach the LH off road rocker trim to the LH off road rocker carrier, and then remove the rocker trim from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the rocker trim panel is fully seated.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 클립 프라이툴
    • 코드리스 래칫/임팩트 드라이버
    • Ext, Wobble, 1/4" DR, 1.25"
    • Plastic Trim Tool
    그림 5. LH off road rocker trim front bolt shown; RH similar
    그림 6. LH off road rocker trim rear bolt shown; RH similar
  10. Remove the bolts (x5) and release the clips (x13) that attach the LH off road rocker carrier to the LH off road structural rocker, and then remove the rocker carrier from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 클립 프라이툴
    • 코드리스 래칫/임팩트 드라이버
    • Ext, Wobble, 1/4" DR, 1.25"
    • Plastic Trim Tool
    그림 7. LH shown; RH similar
    그림 8. LH shown; RH similar
    그림 9. LH shown; RH similar
  11. With assistance, remove the bolts (x2) that attach the LH off road structural rocker to the LH front and rear door rings, and then remove the structural rocker from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    If assistance is unavailable, place a shop rag between the floor jack and structural rocker to protect the structural rocker paint, and then use a floor jack to support the structural rocker.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 4인치 익스텐션
    • 10mm 딥소켓
    • 코드리스 래칫/임팩트 드라이버
    • Floor Jack
    그림 10. LH off road structural rocker to rear door ring bolt shown; RH similar
    그림 11. LH off road structural rocker to front door ring bolt shown; RH similar
  12. Remove the bolts (x6) that attach the LH off road structural rocker to the front rocker support bracket.
    Informational PurposesAn informational icon, calling your attention
    참고
    Avoid moving the front rocker support bracket U-nuts from the center holes during bolt removal.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 4인치 익스텐션
    • 코드리스 래칫/임팩트 드라이버
    • 외부 Torx Plus EP10
    그림 12. LH shown; RH similar
    그림 13. LH shown; RH similar
  13. Remove the bolts (x6) that attach the LH off road structural rocker to the rear rocker support bracket.
    Informational PurposesAn informational icon, calling your attention
    참고
    Avoid moving the rear rocker support bracket U-nuts from the center holes during bolt removal.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 4인치 익스텐션
    • 코드리스 래칫/임팩트 드라이버
    • 외부 Torx Plus EP10
    그림 14. LH shown; RH similar
  14. Remove the bolts (x5) that attach the LH off road structural rocker to the vehicle under body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The forwardmost bolt is longer with a 15 mm drive size.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 딥소켓
    • 15mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    그림 15. Vehicle shown on lift for clarity purposes
  15. Repeat step 5 through step 14 for the RH off road armor parts as required, and then continue to the next step.
  16. Fully raise the vehicle using the rocker lift points. See 차량 상승 - 2 포스트 리프트.
  17. Position the HV battery table under the HV battery off road armor assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the battery table is centered and level.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 1020566-00-F - HV Battery Table
  18. Lower the vehicle until the HV battery table is nearly touching the HV battery off road armor assembly. See 차량 상승 - 2 포스트 리프트.
  19. Remove the bolts (x4) that attach the HV battery off road armor assembly to the HV battery ski rail.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 15mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  20. Remove the bolts (x4) that attach the front side of the HV battery off road armor assembly to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    그림 16. Total number of HV battery front and rear fasteners shown for clarity
  21. Remove the bolts (x5) that attach the rear side of the HV battery off road armor assembly to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    그림 17. Total number of HV battery front and rear fasteners shown for clarity
  22. Slowly raise the vehicle and place the HV battery off road armor assembly on the HV battery table. See 차량 상승 - 2 포스트 리프트.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the battery table is centered and level.
  23. Remove the HV battery off road armor assembly and the HV battery table from the workspace.

장착

  1. Inspect the LH and RH front and rear rocker support bracket U-nuts (x24) for signs of wear or looseness.
    Informational PurposesAn informational icon, calling your attention
    참고
    Worn U-nuts may fall into the rocker structures when being reused. Replace any worn or loose U-nuts as required.
  2. Position the HV battery off road armor assembly and the HV battery table under the vehicle.
  3. Align the HV battery off road armor assembly and HV battery fastener holes (x23), and then raise the HV battery table until the armor assembly is flush against the HV battery.
  4. Prepare the HV battery off road armor assembly fasteners for installation.
  5. Hand-tighten the bolts (x4) that attach the HV battery off road armor assembly to the HV battery ski rail.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
  6. Hand-tighten the bolts (x4) that attach the front side of the HV battery off road armor assembly to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 18. Total number of HV battery front and rear fasteners shown for clarity
  7. Hand-tighten the bolts (x5) that attach the rear side of the HV battery off road armor assembly to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 19. Total number of HV battery front and rear fasteners shown for clarity
  8. Raise the vehicle and remove the HV battery table from the workspace. See 차량 상승 - 2 포스트 리프트.
  9. Lower the vehicle until the tires touch the ground. See 차량 상승 - 2 포스트 리프트.
  10. With assistance, position the LH off road structural rocker on the vehicle, and then hand-tighten the bolts (x2) that attach the structural rocker to the LH front and rear door rings.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    If assistance is unavailable, place a shop rag between the floor jack and structural rocker to protect the structural rocker paint, and then use a floor jack to position the structural rocker on the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 20. LH off road structural rocker to rear door ring bolt; RH similar
    그림 21. LH off road structural rocker to front door ring bolt; RH similar
  11. Hand-tighten the bolts (x5) that attach the LH off road structural rocker to the vehicle under body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The forwardmost bolt is longer with a 15 mm drive size. Do not install the longer bolt in the incorrect fastener hole.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 22. LH shown; RH similar
  12. Hand-tighten the bolts (x6) that attach the LH off road structural rocker to the front rocker support bracket.
    Informational PurposesAn informational icon, calling your attention
    참고
    Install the first bolt on the second fastener hole closest to the front of the vehicle, and then install the remaining bolts while maintaining one exposed fastener hole between every bolt.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 23. LH shown; RH similar
    그림 24. LH shown; RH similar
  13. Hand-tighten the bolts (x6) that attach the LH off road structural rocker to the rear rocker support bracket.
    Informational PurposesAn informational icon, calling your attention
    참고
    Install the first bolt on the second fastener hole closest to the rear of the vehicle, and then install the remaining bolts while maintaining one exposed fastener hole between every bolt.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not torque the bolts at this time.
    그림 25. LH shown; RH similar
  14. Torque the bolts (x5) that attach the LH off road structural rocker to the vehicle under body.
    28 Nm (20.6 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The forwardmost bolt is longer with a 15 mm drive size.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the bolts that attach the structural rocker to the vehicle under body are torqued first before proceeding to the next step.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 딥소켓
    • 15mm 딥소켓
    • 각도 측정 토크 렌치
  15. Torque the bolts (x6) that attach the LH off road structural rocker to the front rocker support bracket.
    13 Nm (9.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx Plus EP10
    • 각도 측정 토크 렌치
    그림 26. LH shown; RH similar
  16. Torque the bolts (x6) that attach the LH off road structural rocker to the rear rocker support bracket.
    13 Nm (9.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx Plus EP10
    • 각도 측정 토크 렌치
    그림 27. LH shown; RH similar
  17. Torque the bolts (x2) that attach the LH off road structural rocker to the LH front and rear door rings.
    14 Nm (10.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 각도 측정 토크 렌치
    그림 28. LH off road structural rocker to rear door ring bolt; RH similar
    그림 29. LH off road structural rocker to front door ring bolt; RH similar
  18. Position the LH off road rocker carrier on the vehicle, engage the clips (x13), and then install the bolts (x5) that attach the LH off road rocker carrier to the LH off road structural rocker.
    13 Nm (9.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the carrier clips are fully seated first, and then install the bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    • Ext, Wobble, 1/4" DR, 1.25"
    • 각도 측정 토크 렌치
    그림 30. LH shown; RH similar
    그림 31. LH shown; RH similar
    그림 32. LH shown; RH similar
    그림 33. LH shown; RH similar
  19. Position the LH off road rocker trim on the vehicle, engage the clips (x14), and then install the bolts (x2) that attach the LH off road rocker trim to the LH off road rocker carrier.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the rocker trim panel is fully seated.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    • Ext, Wobble, 1/4" DR, 1.25"
    • 각도 측정 토크 렌치
    그림 34. LH shown; RH similar
    그림 35. LH shown; RH similar
    그림 36. LH shown; RH similar
    그림 37. LH off road rocker trim front bolt; RH similar
    그림 38. LH off road rocker trim rear bolt; RH similar
  20. Secure the clips (x13) that attach the front of the LH rear fender flare cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Replace any missing or damaged clips.
    그림 39. LH shown; RH similar
  21. Install the clip that attaches the LH rocker cover to the LH rear wheel liner.
    그림 40. LH shown; RH similar
  22. Connect the electrical connector, and then secure the clips (x11) that attach the rear of the LH fender flare cover to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Replace any missing or damaged clips.
    그림 41. LH shown; RH similar
  23. Install the clip that attaches the LH rocker cover to the LH front wheel liner.
    그림 42. LH shown; RH similar
  24. Repeat steps 10 through 23 for the RH off road armor parts as required, and then continue to the next step.
  25. Fully raise the vehicle. See 차량 상승 - 2 포스트 리프트.
  26. Torque the bolts (x4) that attach the front side of the HV battery off road armor assembly to the HV battery.
    28 Nm (20.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 6인치 익스텐션
    • 13mm 소켓
    • 각도 측정 토크 렌치
    그림 43. Total number of HV battery front and rear fasteners shown for clarity
  27. Install the new bolts (x5) that attach the rear side of the HV battery off road armor assembly to the HV battery.
    28 Nm (20.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 6인치 익스텐션
    • 13mm 소켓
    • 각도 측정 토크 렌치
    그림 44. Total number of HV battery front and rear fasteners shown for clarity
  28. Torque the bolts (x4) that attach the HV battery off road armor assembly to the HV battery ski rail.
    26 Nm (19.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 15mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  29. Fully lower the vehicle. See 차량 상승 - 2 포스트 리프트.
  30. ODIN 루틴 실행 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link).
  31. 터치스크린에서 컨트롤 > 서스펜션 > 표준을 터치하여 차량 지상고를 표준으로 설정합니다.
  32. LH 전면 창문을 올립니다.
  33. LH 전면 도어를 닫습니다.