2026-03-06

Bridge - Track Motor - 1st Row Seat - LH (Remove and Install)

교정 코드 13010102601 0.66 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Cybertruck의 전자 장치는 효율성을 개선하기 위해 설계된 48V "중간 전압(MV)" 아키텍처로 구동됩니다. MV 구성품을 정비할 때는 부상 및/또는 차량 손상을 피하기 위해 추가적인 지식과 주의가 필요합니다. 전기 사전 주의 사항의 MV 사전 주의 사항을 읽고 이해하며 해당하는 경우 필요한 MV 관련 교육 과정을 이수했는지 확인합니다.
  • 2026-01-26: Released new procedure.
  1. Remove the LH front seat assembly from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Install).
  2. Place LH front seat on a protected surface
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance, Place seat so the underside of the seat can be accessed
  3. Disconnect LH front seat track motor
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  4. Release LH front seat harness from track bridge
    Informational PurposesAn informational icon, calling your attention
    참고
    3x Clips
  5. Remove outboard bolts securing seat track to seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    참고
    2x patch bolts, T45P, 23 Nm, Discard after removal
  6. Release outboard track from bridge motor
    Informational PurposesAn informational icon, calling your attention
    참고
    1x tab, Pry up on bridge tack motor tab and slide outboard seat track away to release
  7. Release track motor bridge from inboard track
    Informational PurposesAn informational icon, calling your attention
    참고
    1x tab, Pry up on track motor bridge tab and slide away from inboard track
  8. Install track motor bridge to inboard seat track
    Informational PurposesAn informational icon, calling your attention
    참고
    1x tab, Track motor cable is keyed square and must be aligned with inboard track, Turn cable by hand to align as needed, Slide track motor bridge into inboard track till fully seated to secure
  9. Install outboard seat track to track motor bridge
    Informational PurposesAn informational icon, calling your attention
    참고
    1x tab, Track motor cable is keyed square and must be aligned with outboard track, Turn cable by hand to align as needed, Slide outboard track into track motor bridge till fully seated to secure
  10. Install outboard bolts securing seat track to seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    참고
    2x patch bolts, T45P, 23 Nm, Install new patch bolts
  11. Secure LH front seat harness to track bridge
    Informational PurposesAn informational icon, calling your attention
    참고
    3x Clips
  12. Connect LH front seat track motor
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  13. Install the LH front seat assembly into the vehicle. See Seat Assembly - 1st Row - LH (Remove and Install).