교정 코드 16300105801 16300105802 1.74 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. 차량을 들어 올려서 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
2. 전동식 프렁크를 엽니다.
3. 테일게이트를 엽니다.
4. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
5. MV 전원을 연결 해제합니다. 참조 항목: Disconnect MV Power.
6. Verify operation of multimeter
   참고

   Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals

   

   

7. Raise vehicle fully and lower lift onto locks
   참고

   Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
8. Remove rear skid plate
   참고

   6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm

   

   

   

   

   

9. Remove all items from pockets and ensure not wearing metal items

   

10. Inspect HV insulating gloves
    참고

    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.

    

11. Put on HV insulating gloves and leather over gloves
    참고

    Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration.

    

12. Verify no HV - Install amp clamp to RDU HV harness
    참고

    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.Release locking tab and rotate the release lever up to disengage the connector, Release harness clip, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damagedMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

    

    

13. Secure RDU header connector to ancillary
    참고

    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

    

    

14. Remove pyro fuse access cover
    참고

    4x bolts, E-Torx 5 lobe, 10 Nm

    

15. Remove primary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

16. Remove secondary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

17. Install pyro fuse access cover
    참고

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

    

    

18. Remove leather over gloves and HV insulating gloves
19. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
20. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
21. Disconnect ancillary bay MV connector
    참고

    1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing

    

    

    

    

    

22. Put on HV insulating gloves and leather over gloves

    

23. Remove bolt securing busbar HV connector lid
    참고

    1x bolt, EP10, 9 Nm

    

24. Remove bolts securing HV connector to DC FC header
    참고

    2x bolts, 10mm, 9 Nm

    

25. Release HV connector from DC FC header
    참고

    1x connector, Use inflatable airbag to suspend busbar assembly above ancillary assembly

    

26. Support HV Busbar assembly
    참고

    Suspend assembly to maintain clearance

    

27. Remove fast charger header doubler
    참고

    2x bolts, E10 5 Lobe Torx, 10 Nm

    

    

28. Release low voltage header
    참고

    2x bolts, EP10, 6 Nm

    

29. Release fasteners securing ancillary cover to HV battery
    참고

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

30. Remove ancillary cover
    참고

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

31. Remove bolts securing PCS fuse
    참고

    2x bolts, 8mm, 6 Nm

    

    

32. Remove PCS fuse

    

    

33. Install HV compressor fuse
    참고

    Verify fuse is in the correct orientation

    

    

    

    

34. Install bolts securing HV compressor fuse
    참고

    2x bolts, 8mm, 6 Nm

    

35. Perform Hioki measurement from PCS fuse joint to FCC harness terminal
    참고

    1x HV joint, 200μΩ or less, Perform zero adjust to Hioki meter prior to testing

    

    

36. Perform Hioki measurement from PCS fuse joint to PCS harness terminal
    참고

    1x HV joint, 200μΩ or less, Perform zero adjust to Hioki meter prior to testing

    

    

    

37. Install ancillary cover
    참고

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

    

38. Secure fasteners of cover to HV battery
    참고

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

39. Secure low voltage header
    참고

    2x bolts, EP10, 6 Nm

    

40. Secure fast charger header doubler
    참고

    2x bolts, E10 5 Lobe Torx, 10Nm

    

    

41. Clean HV connector contact surface of residual Penetrox
    참고

    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

    

42. Clean busbar HV connector contact surface of residual Penetrox
    참고

    Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

    

43. Apply Penetrox onto HV connector joints
    참고

    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

    

44. Position busbar connector and lower onto HV header
    참고

    Release bungee cord

    

45. Install bolts securing charge port busbar kit to HV Header
    참고

    2x bolts, 10mm, 9 Nm

    

46. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    참고

    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

47. Install bolt securing busbar HV connector lid
    참고

    1x bolt, EP10, 9 Nm

    

48. Connect Ancillary bay MV connector
    참고

    1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly

    

    

    

    

    

49. Raise vehicle fully and lower lift onto locks
    참고

    Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
50. Remove pyro fuse access cover
    참고

    4x bolts, E-Torx 5 lobe, 10 Nm

    

51. Clean pyro fuse mating surfaces
    참고

    Using an insulated tool wipe all four busbar mating surfaces within pyro fuse bay, Wipe top and bottom mating surfaces of each pyro fuse, Ensure no debris is present on any mating surface, Process shown with device cluster removed for clarity and safety, HV gloves and associated PPE must be worn at all times when cleaning mating surfaces, Allow 1 minute for IPA to dry

    

    

    

52. Install secondary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

53. Install primary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

54. Perform Hioki resistance test at each HV joint from HV busbar lead to pyro fuse busbar
    참고

    4x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

55. Install pyro fuse access cover
    참고

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

    

    

56. Remove leather over gloves and HV insulating gloves
57. Install rear skid plate
    참고

    6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm, Apply Loctite 222 to mid aero shield bolts and install fasteners

    

    

    

    

    

58. Lower vehicle fully
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
59. MV 전원을 다시 연결합니다. 참조 항목: Disconnect MV Power.
60. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
61. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
62. 테일게이트를 닫습니다.
63. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.