교정 코드 44000134 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
2. 차량을 들어 올려서 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
3. Connect a laptop with Toolbox to the vehicle. See Toolbox 3(연결 및 연결 해제).
4. Select "Actions" and search for "diagnostic_path_network.HV_isolationCheck"
5. Select "HV Isolation Diagnostic Debug", enter VIN, and click run
6. Read "HV System Global Check Autodiag" question and select "Yes" to continue
7. Read "HV Awareness" warning and select "Yes" to continue
8. Read interactive procedure instructions and select "Next" to continue
   참고

   Select "Finish Later" every time you need to perform a task to prevent timeout error, Select "Resume" after task has been performed and you are ready to submit input
9. Read "Vehicle Electrical Isolation Procedure" panel and select "Finish Later" to prevent timeout error
10. 전동식 프렁크를 엽니다.
11. 테일게이트를 엽니다.
12. MV 전원을 연결 해제합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
13. Verify operation of multimeter
    참고

    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals

    

    

14. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3(연결 및 연결 해제).
15. Remove rear skid plate. See Skid Plate - Rear (Remove and Install).
16. Remove all items from pockets and ensure not wearing metal items

    

17. Inspect HV insulating gloves
    참고

    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.

    

18. Put on HV insulating gloves and leather over gloves

    

19. Remove clips securing AC compressor HV harness
    참고

    3x clips

    

20. Verify no HV - Install amp clamp to RDU HV harness
    참고

    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.Release locking tab and rotate the release lever up to disengage the connector, Release harness clip, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damagedMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

    

    

21. Select "Resume" to continue to "Vehicle Electrical Isolation Procedure" panel
    참고

    Read panel and select "Yes" to continue
22. Read "Rear Left DU + HV Harness Isolation Test" panel and select "Finish Later" to prevent timeout error
23. Perform isolation test on LH RDU HV cable at HV battery
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to subframe bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

24. Select "Resume" to continue to "Rear Left DU + HV Harness Isolation Test" panel
    참고

    Read panel and submit resistance to continue
25. Read "Rear Left DU + HV Harness Voltage Check" panel and select "Continue"
26. Read "Rear Right DU + HV Harness Isolation Test" panel and select "Finish Later" to prevent timeout error
27. Disconnect RDU HV harness
    참고

    1x connector, Release locking tab and rotate release lever up, Do not force release lever up, Ensure alignment tabs on header are not damaged

    

28. Perform isolation test on RH RDU HV cable at HV battery
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to subframe bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

29. Select "Resume" to continue to "Rear Right DU + HV Harness Isolation Test" panel
    참고

    Read panel and submit resistance to continue
30. Read "Rear Right DU + HV Harness Voltage Check" panel and select "Continue"
31. Read "FDU + HV Harness Isolation Test" panel and select "Finish Later" to prevent timeout error
32. Disconnect FDU HV harness from HV battery
    참고

    1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged

    

33. Perform isolation test on FDU HV cable at rear of HV battery
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to subframe bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

34. Select "Resume" to continue to "FDU + HV Harness Isolation Test" panel
    참고

    Read panel and submit resistance to continue
35. Read "FDU + HV Harness Voltage Check" panel and select "Continue"
36. Read "Heat Pump A/C Compressor + HV Harness' Isolation Tests" panel and select "Finish Later" to prevent timeout error
37. Release A/C compressor HV harness from HV battery
    참고

    1x locking connector, 4x clips, Pull down red locking tab and disengage the release lever, Do not force the release lever up, Number of connections may vary by vehicle configuration

    

    

    

38. Perform isolation test on ancillary HV harness at rear of HV battery
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to subframe bolt, Position leads then press test button, Amber light will turn on, Test all four terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

39. Select "Resume" to continue to "Heat Pump A/C Compressor + HV Harness' Isolation Tests" panel
    참고

    Read panel and submit resistance to continue
40. Read CP HV Harness FC contactor question and select "Yes" to continue
41. Read "CP HV Harness Isolation Test" panel and select "Finish Later" to prevent timeout error
42. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
43. Remove bed floor assembly
    참고

    10x bolts, 15mm, 56 Nm, 4x anchors, Open anchors as needed, Lift front edge with trim tool then remove panel, Recommend assistance

    

    

    

44. Remove bolt securing busbar HV connector lid
    참고

    1x bolt, EP10, 9 Nm

    

45. Remove bolts securing HV connector to DC FC header
    참고

    2x bolts, 10mm, 9 Nm

    

46. Release HV connector from DC FC header
    참고

    1x connector, Use inflatable airbag to suspend busbar assembly above ancillary assembly

    

47. Secure CP busbar connector aside
    참고

    Move connector away from header, Install bags or bungees as needed, Do not open tonneau to prevent damage

    

48. Perform isolation test on CP HV busbar connector
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to door stricker, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

49. Select "Resume" to continue to "CP HV Harness Isolation Test" panel
    참고

    Read panel and submit resistance to continue
50. Read Ancillary certification question and select "Yes" to continue
51. Read "PCS2 DC Isolation Test" panel and select "Finish Later" to prevent timeout error
52. Connect HV harness connector to AC compressor
    참고

    1x locking electrical connector, Slide down black lock then push in red locking tab, Perform a push-pull-push test, Ensure red locking tab is fully engaged, Black tab will protrude from red locking tab when engaged correctly, Refer to images and video for clarity

    

    

    

    

53. Remove the frunk assembly. See Frunk Assembly (Remove and Install).
54. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
55. 적재함 커버를 엽니다.
56. Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
57. Remove the tonneau NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
58. MV 전원을 연결 해제합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
59. Raise vehicle fully
    참고

    Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
60. Verify no HV - Install amp clamp to RDU HV harness
    참고

    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.Release locking tab and rotate the release lever up to disengage the connector, Release harness clip, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damagedMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

    

    

61. Disconnect pressurized pack lines
    참고

    2x VOSS fittings, 12mm, 8Nm

    

62. Remove VOSS fitting from pressurized pack air lines
    참고

    2x VOSS fitting, Slide threaded section back, Remove the collet, Then slide threaded section off of air line

    

    

63. Remove pyro fuse access cover
    참고

    4x bolts, E-Torx 5 lobe, 10 Nm

    

64. Remove primary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

65. Remove secondary pyro fuse
    참고

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

66. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
67. Remove rear tonneau cover box cross supports
    참고

    8x screws, T25, 5 Nm

    

    

68. Clean all debris from ancillary cover
    참고

    During removal of ancillary cover any debris on top of the cover may be deposited into the ancillary bay

    

69. Release ANC air line from pressurized pack valve block
    참고

    1x VOSS fitting, 12mm, 8 Nm, Do not release air line to reservoir, Rapid loss of pressure will result if wrong air line is released

    

70. Remove VOSS air fitting from ANC air line
    참고

    1x VOSS fitting, Slide threaded section back, Remove collet, Then slide threaded section off of air line, Discard after removal

    

    

71. Release pressurized pack valve block from air suspension reservoir
    참고

    1x bolt, 10mm, 5 Nm, 1x connector, 1x clip, 1x zip tie, Release lock before connector disengagement, Cut zip tie at reservoir and ancillary air line bundle

    

    

72. Release air suspension valve block
    참고

    3x rubber grommets, Rotate clockwise until top 2 rubber feet have released from bracket, Pull upwards at 45 degree angle to release bottom rubber foot from bracket, Leave all air lines and connections secured and set assembly aside

    

    

    

73. Release air suspension reservoir
    참고

    2x nuts, 13mm, 33 Nm, 2x fir tree clips

    

    

74. Place air suspension reservoir in service position then install Ancillary Access Bench
    참고

    Raise and swing air suspension reservoir to the side of the bed, Place Ancillary Access Bench onto rear casting ensuring no air lines or harnesses are being pinched

    

    

    

75. Disconnect ancillary bay MV connector
    참고

    1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing

    

    

    

    

    

76. Support HV Busbar assembly
    참고

    Suspend assembly to maintain clearance

    

77. Remove fast charger header doubler
    참고

    2x bolts, E10 5 Lobe Torx, 10 Nm

    

    

78. Release low voltage header
    참고

    2x bolts, EP10, 6 Nm

    

79. Release fasteners securing ancillary cover to HV battery
    참고

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

80. Remove ancillary cover
    참고

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

81. Disconnect PCS2 DC HV connector
    참고

    1x connector, Release locking tab, Gently pull up

    

82. Perform isolation test on PCS2 DC connector at ancillary
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to HV battery chassis bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

83. Select "Resume" to continue to "PCS2 DC Isolation Test" panel
    참고

    Read panel and submit resistance to continue
84. Read "ACJB Isolation Test" panel and select "Finish Later" to prevent timeout error
85. Release ancillary bay MV connector header
    참고

    4x tabs, Move aside as needed

    

    

86. Disconnect HVC logic connector
    참고

    1x connector

    

87. Disconnect negative pack contactor sense connectors
    참고

    2x connectors

    

88. Disconnect positive pack contactor sense connectors
    참고

    2x connectors

    

    

89. Disconnect ACJB HV connector
    참고

    1x connector, Release locking tab, Gently pull up

    

90. Perform isolation test on ACJB HV connector
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to HV battery chassis bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

91. Select "Resume" to continue to "ACJB Isolation Test" panel
    참고

    Read panel and submit resistance to continue
92. Read "External Side DC Link Isolation Test" panel and select "Finish Later" to prevent timeout error
93. Perform isolation test on external side of negative and positive pack contactors
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to HV battery chassis bolt, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

    

94. Select "Resume" to continue to "External Side DC Link Isolation Test" panel
    참고

    Read panel and submit resistance to continue
95. Read "Internal Side DC Link Isolation Test" panel and select "Finish Later" to prevent timeout error
96. Perform isolation test on internal side of negative and positive pack contactors and pyro disconnect
    참고

    Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to HV battery chassis bolt, Position leads then press test button, Amber light will turn on, Test all four terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

    

    

    

    

    

    

    

97. Select "Resume" to continue to "Internal Side DC Link Isolation Test" panel
    참고

    Read panel and submit resistance to continue
98. Read "Warm Heat Pump A/C Compressor Isolation Test" panel and select "Finish Later" to prevent timeout error
99. Connect ACJB HV connector
    참고

    1x connector, Secure locking tab

    

100. Connect positive pack contactor sense connectors
     참고

     2x connectors

     

     

101. Connect negative pack contactor sense connectors
     참고

     2x connectors

     

102. Connect HVC logic connector
     참고

     1x connector

     

103. Secure ancillary bay MV connector header
     참고

     4x tabs

     

104. Connect PCS2 DC HV connector
     참고

     1x connector, Secure locking tab

     

105. Install ancillary cover
     참고

     Use suction cup and maneuver around busbar and tonneau cage

     

     

     

     

106. Secure fasteners of cover to HV battery
     참고

     22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

     

     

     

107. Secure low voltage header
     참고

     2x bolts, EP10, 6 Nm

     

108. Secure fast charger header doubler
     참고

     2x bolts, E10 5 Lobe Torx, 10Nm

     

     

109. Clean HV connector contact surface of residual Penetrox
     참고

     Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

     

110. Clean busbar HV connector contact surface of residual Penetrox
     참고

     Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

     

111. Apply Penetrox onto HV connector joints
     참고

     Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

     

112. Position busbar connector and lower onto HV header
     참고

     Release bungee cord

     

113. Install bolts securing charge port busbar kit to HV Header
     참고

     2x bolts, 10mm, 9 Nm

     

114. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
     참고

     2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

     

     

115. Install bolt securing busbar HV connector lid
     참고

     1x bolt, EP10, 9 Nm

     

116. Connect Ancillary bay MV connector
     참고

     1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly

     

     

     

     

     

117. Secure rear tonneau cover box cross supports
     참고

     8x screws, T25, 5 Nm, Supports install in the same direction of the fasteners

     

     

118. Install the tonneau NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
119. Remove Ancillary Access Bench then place air suspension reservoir into position for installation
     참고

     Ensure air lines are not twisted, Ensure no harnesses are caught

     

     

     

120. Secure air suspension reservoir
     참고

     2x nuts, 13mm, 33 Nm, 2x fir tree clips

     

     

121. Secure air suspension valve block
     참고

     3x rubber grommets, Rotate counter-clockwise until top 2 rubber feet are secured onto bracket, Push downwards at 45 degree angle to secure bottom rubber foot into bracket, Position air lines and connections into place for installation

     

     

     

122. Install new VOSS air fitting onto ANC air line
     참고

     1x VOSS fitting, 12mm, 8 Nm, Do not remove VOSS plastic plug until pressurized pack line is installed

     

     

123. Secure ANC air line onto pressurized pack valve block
     참고

     1x line, Remove plastic cap from VOSS fittings, Press air lines onto fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test

     

     

124. Secure pressurized pack valve block onto air suspension reservoir
     참고

     1x bolt, 10mm, 5 Nm, 1x connector, 1x clip, 1x zip tie, Secure reservoir and ancillary air lines at white marked sections

     

     

125. Raise vehicle fully
     참고

     Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
126. Clean mating surface of the pyro
     참고

     Use a non-conductive plastic tool to clean the busbar side, Allow 1 minute for IPA to fully dry, Do not use any other types of cleaner

     

     

     

127. Install secondary pyro fuse
     참고

     2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts

     

     

128. Install primary pyro fuse
     참고

     2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts

     

     

129. Perform Hioki resistance test at each HV joint from HV busbar lead to pyro fuse busbar
     참고

     4x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

     

     

130. Remove HV insulating gloves
131. Install new Voss fittings and nut onto pyro cover
     참고

     2x VOSS fittings, 12mm, 8 Nm, Do not remove VOSS plastic plug until pressurized pack air line install

     

     

132. Install pyro fuse access cover
     참고

     4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

     

     

133. Install pressurized pack lines
     참고

     2x VOSS fittings, 12mm, 8 Nm, Remove plastic caps from VOSS fittings if installing new fuse cover, Press air lines into fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test

     

     

134. Secure A/C compressor HV harness onto battery
     참고

     1x locking connector, 4x clips, Engage locking tab, Do not force lever up, Number of connections may vary by vehicle configuration

     

     

     

135. Connect FDU HV harness to HV battery
     참고

     1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

     

136. Connect RDU HV harness
     참고

     1x connector, Verify lever is upright and in open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

     

137. Connect LHS RDU HV harness
     참고

     1x connector, Verify lever is upright and in open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

     

138. Install clips securing AC compressor HV harness
     참고

     3x clips

     

139. Install the rear skid plate. See Skid Plate - Rear (Remove and Install).
140. Lower vehicle until tires are touching the ground
     참고

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
141. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
142. Remove the frunk assembly. See Frunk Assembly (Remove and Install).
143. Warm up AC compressor via UI
     참고

     Via Climate Control > ON, Set fan speed to 10, Set temperature to HI or LO, Allow 20 minute run time

     

144. Turn off the AC and blower motor

     

145. MV 전원을 연결 해제합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
146. Disconnect HV harness connector from AC compressor
     참고

     1x locking electrical connector, Pull red locking tab away from compressor then slide black lock upwards to release

     

     

147. Perform isolation test on AC compressor
     참고

     Move HV harness aside as needed, Set insulation meter to 1000V and red lead to resistance (Ω), Secure black alligator clip to shock tower brace, Position leads then press test button, Amber light will turn on, Test both terminals, Make sure to wear proper PPE, Verify voltage drops below 10V after releasing test button

     

     

     

     

     

148. Select "Resume" to continue to "Warm Heat Pump A/C Compressor Isolation Test" panel
     참고

     Read panel and submit resistance to continue
149. Read "HV Isolation Diagnostic Debug" results
     참고

     If this panel is reached then screenshot and escalate a Toolbox session, Select "X" at top right of window to close once complete
150. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
151. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
152. Install bed floor assembly
     참고

     10x bolts, 15mm, 56 Nm, 4x anchors, Open and close anchors as needed, Recommend assistance

     

     

     

153. Install the tonneau slats. See Slat System - Tonneau (Remove and Install).
154. 정비 모드를 종료합니다. 참조 항목: 정비 모드.
155. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
156. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.