2025-10-03

Acoustic Cover - Compressor (Remove and Install)

교정 코드 1820026021 FRT 1.86 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2024-05-22: 커넥터 이미지 및 연결 해제/연결 지침을 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

탈거

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. 차량을 정비 모드로 설정합니다. 참조 항목: 정비 모드.
  3. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  4. 차량 터치스크린에서 냉매 시스템으로 이동합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    정비 모드 > 열 관리 > 냉매 시스템을 터치합니다.
  5. Start Thermal Fill Drain (Refrigerant only)을 터치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    루틴이 완료될 때까지 기다립니다. 루틴이 성공했는지 확인합니다.
  6. 차량을 2포스트 리프트에 올리고 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  7. 전동식 프렁크를 엽니다.
  8. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
  9. 프렁크를 탈거합니다. 참조 항목: Frunk Assembly (Remove and Install).
  10. MV 전원을 연결 해제합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
  11. 차량 HV 비활성화 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure (Test/Adjust).
  12. A/C 냉매를 회수합니다. 참조 항목: A/C 냉매(회수 및 충전).
  13. 원격 브레이크 오일 저장 탱크를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 1개, 10mm, 8Nm, 기준점 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    위로 들어올려 기준점을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    옆으로 치워둡니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전도되지 않도록 하십시오.
  14. A/C 컴프레서 로직 전기 커넥터를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    잠금 전기 커넥터 1개. 빨간색 탭을 누르지 마십시오. 잠금 장치를 당겨 체결을 해제한 다음 다시 당겨 전기 커넥터를 분리합니다.
  15. 커넥터 잠금 장치를 푼 다음 A/C 컴프레서에서 A/C 컴프레서 HV 하네스 전기 커넥터를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    빨간색 잠금 탭을 검은색 레버에서 당겨 빼낸 다음 검은색 레버를 위로 밉니다.
  16. A/C 컴프레서 접지 스트랩을 고정하는 볼트를 탈거합니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    접지를 분리한 후 하네스 엣지 클립을 풉니다.
  17. 차량에서 A/C 호스를 탈거합니다.
  18. A/C 컴프레서를 메가빔에 고정하는 볼트(3개)를 탈거합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 작업자의 도움을 받는 것이 좋습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    패스너를 탈거하는 동안 A/C 컴프레서를 지지합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    A/C 컴프레서를 차량 전면 쪽과 메가빔 아래로 조심스럽게 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    펜더 커버를 팬 하우징에 놓고 A/C 컴프레서 어셈블리를 조심스럽게 내려 놓습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    MV 또는 HV 하네스에 무리가 가지 않도록 주의하십시오.
  19. A/C 컴프레서에서 냉매 흡입 및 배출 라인을 고정하는 너트(2개)를 탈거한 다음 A/C 컴프레서에서 라인을 탈거합니다.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    너트(2개)를 탈거한 다음 A/C 컴프레서에서 A/C 라인을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    와셔가 A/C 컴프레서에 남아 있지 않도록 주의하십시오.
  20. 차량에서 A/C 컴프레서를 탈거합니다.
  21. 기존 A/C 컴프레서에서 NVH 커버를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    탭 5개

장착

  1. NVH 커버를 새 A/C 컴프레서에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    탭 5개
    Informational PurposesAn informational icon, calling your attention
    참고
    NVH 커버가 확실히 고정되었는지 확인합니다.
  2. 냉매 흡입 및 배출 라인을 A/C 컴프레서에 장착한 다음 너트(2개)를 조입니다.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    새 와셔 씰을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    A/C 라인을 스터드에 배치한 다음 너트를 장착합니다.
  3. A/C 컴프레서를 메가빔에 고정하는 볼트(3개)를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 작업자의 도움을 받는 것이 좋습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    패스너를 장착하는 동안 A/C 컴프레서를 지지합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트를 손으로 체결합니다.
  4. 원격 브레이크 오일 저장 탱크를 고정하는 볼트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 1개, 10mm, 8Nm, 기준점 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    기준점을 맞춘 다음 아래로 밀어 체결합니다.
  5. AC 컴프레서 HV 하네스를 AC 컴프레서에 연결한 다음 커넥터 잠금 장치를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    검은색 레버를 아래로 민 다음 빨간색 잠금 장치를 안쪽으로 밀어 넣습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭이 끝까지 밀려 들어갔는지 확인하십시오. 빨간색 잠금 탭은 검은색 레버와 같은 높이에 있어야 합니다.
    그림 1. 빨간색 잠금 탭이 검은색 레버와 같은 높이에 있음
    그림 2. 빨간색 잠금 탭이 완전히 체결되지 않음
  6. A/C 컴프레서 접지 스트랩을 고정하는 볼트를 장착합니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  7. A/C 컴프레서 로직 전기 커넥터를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    잠금 전기 커넥터 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    잠금 탭을 체결합니다.
  8. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
  9. A/C 진공 테스트를 수행하고 누출 테스트를 실행합니다. 참조 항목: A/C 냉매(회수 및 충전).
  10. A/C 냉매 재충전을 수행합니다. 참조 항목: A/C 냉매(회수 및 충전).
  11. A/C 성능 테스트를 수행합니다. 참조 항목: A/C 냉매(회수 및 충전).
  12. 정비 모드를 종료합니다. 참조 항목: 정비 모드.
  13. 프렁크를 장착합니다. 참조 항목: Frunk Assembly (Remove and Install).
  14. 전동식 프렁크를 닫습니다.
  15. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  16. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.