2025-10-08

BLE End Point - Wheel Well - Front - LH (Remove and Replace)

교정 코드 1745104032 0.18 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  1. Close LH front door
  2. Open LH front door
    Informational PurposesAn informational icon, calling your attention
    참고
    Push LH B-pillar door trigger to release
  3. Lower LH front window
  4. ODIN 루틴 실행 PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
  5. Remove LH front fender flare cover
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 3x datums, 1x connector, Release all clips then repeater connector before removal, Camera harness is very short, Ensure excess force is not exerted on harness
  6. Release LH front wheel liner from fore fender flare carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  7. Remove LH front fore fender flare carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    6x bolts, 10mm, 6 Nm, 1x connector, Disconnect BLE module then remove carrier, Release locking tab
  8. Remove LH front wheel well BLE endpoint
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, T20, 1.5 Nm, Discard bolts
  9. Install LH front wheel well BLE endpoint
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, T20, 1.5 Nm, Install new bolts
  10. Install LH front fore fender flare carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    6x bolts, 10mm, 6 Nm, 1x connector, Connect BLE then install carrier, Engage locking tab
  11. Install clips securing LH front wheel liner to fore fender flare carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  12. Install LH front fender flare cover
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 3x datums, 1x connector, Make camera connection before flare installation, Ensure excess force is not exerted on camera harness, Replace any missing or damaged clips
  13. Reinstall software via UI
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Service Mode > Software Reinstall, Select Reinstall button at Software Reinstall dialogue box, Reinstall will begin immediately, Once firmware redeploy is complete, Verify release notes are present via UI
  14. ODIN 루틴 실행 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  15. Raise LH front window
  16. Close LH front door