2025-10-24

Mount - Inverter - Front Drive Unit (Remove and Install)

교정 코드 3901049101 3901049102 FRT 2.34 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Cybertruck의 전자 장치는 효율성을 개선하기 위해 설계된 48V "중간 전압(MV)" 아키텍처로 구동됩니다. MV 구성품을 정비할 때는 부상 및/또는 차량 손상을 피하기 위해 추가적인 지식과 주의가 필요합니다. 전기 사전 주의 사항의 MV 사전 주의 사항을 읽고 이해하며 해당하는 경우 필요한 MV 관련 교육 과정을 이수했는지 확인합니다.

탈거

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. 차량을 정비 모드로 설정합니다. 참조 항목: 정비 모드.
  3. 차량을 2포스트 리프트에 올리고 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  4. 전동식 프렁크를 엽니다.
  5. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
  6. 프렁크 어셈블리를 탈거합니다. 참조 항목: Frunk Assembly (Remove and Install).
  7. MV 전원을 연결 해제합니다. 참조 항목: Disconnect MV Power.
  8. 차량 HV 비활성화 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure (Test/Adjust).
  9. 하단 밸런스를 차체에 고정하는 볼트(6개)를 탈거합니다.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    클립 2개, 커버 2개
    Informational PurposesAn informational icon, calling your attention
    참고
    커버(2개)를 분리하여 볼트를 노출합니다.
  10. 전면 에어로 실드를 탈거합니다. 참조 항목: Aeroshield - Front (Remove and Install).
  11. FDU HV 하네스를 고정하는 볼트를 탈거한 다음 전기 커넥터를 연결 해제합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    전면 서브프레임에 걸리지 않도록 하네스를 이동합니다.
  12. FDU 로직 전기 커넥터를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치를 풀고 잠금 암을 아래로 돌려 탈거합니다.
  13. 냉각수 수거 용기를 RH 차량 전면 아래에 놓습니다.
  14. 타이어가 지면에 닿을 때까지 차량을 내립니다.
  15. 전면 중앙 아플리케를 탈거합니다. 참조 항목: Front Center Applique Assembly (Remove and Install).
  16. 전면 페시아를 탈거합니다. 참조 항목: Front Fascia (Remove and Install).
  17. 냉각 팬 모듈을 탈거합니다. 참조 항목: Module - Cooling Fan (Remove and Install).
  18. 전륜 구동 장치를 받칩니다.
  19. 인버터 냉각수 리턴 호스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스프링 클립 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    피팅을 끼웁니다.
  20. RH FDU 마운트를 고정하는 볼트를 탈거합니다.
    85 Nm (62.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E18
  21. NVH 패드를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    클립 7개
    Informational PurposesAn informational icon, calling your attention
    참고
    수정 사항은 벨크로로 고정할 수 있습니다.
  22. RH 마운트를 고정하는 볼트(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E14
    Informational PurposesAn informational icon, calling your attention
    참고
    토크: 35Nm +55도
    Informational PurposesAn informational icon, calling your attention
    참고
    최전방 볼트 2개를 탈거합니다. 마지막 볼트는 이후 단계에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    명확하게 보이도록 전륜 구동 장치를 차량에서 탈거한 상태의 이미지입니다.
  23. LH FDU 마운트를 고정하는 볼트를 탈거합니다.
    85 Nm (62.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E18
    Informational PurposesAn informational icon, calling your attention
    참고
    HCU 브래킷의 관통 구멍을 통해 볼트에 접근합니다.
  24. 언더호이스트 스탠드를 내려 치웁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전륜 구동 장치는 전면 서브프레임 위에 놓입니다.
  25. 인버터 냉각수 인입 호스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스프링 클립 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    피팅을 끼웁니다.
  26. 전륜 구동 장치에 마운트를 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E14
    Informational PurposesAn informational icon, calling your attention
    참고
    남은 볼트 하나를 탈거합니다. 전륜 구동 장치를 LH 측으로 이동하여 간격을 확보합니다. 인버터 마운트를 차량에서 조심스럽게 빼냅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    토크: 35Nm +55도

장착

  1. 인버터 마운트를 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 1개, E14
    Informational PurposesAn informational icon, calling your attention
    참고
    인버터 마운트를 제자리에 배치합니다. 전륜 구동 장치를 LH 측으로 이동하여 간격을 확보합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    하부 볼트를 느슨하게 장착합니다. 이후 단계에서 규격 토크로 조입니다.
  2. 인버터 냉각수 인입 호스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스프링 클립 1개
  3. NVH 커버를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼 앤 소켓 클립 6개
  4. FDU 로직 전기 커넥터를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    잠금 암을 위로 돌려 고정합니다.
  5. FDU HV 하네스를 고정합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    전기 커넥터 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    잠금 탭이 체결되었는지 확인합니다.
  6. 전륜 구동 장치를 받칩니다.
  7. RH 구동 장치 마운트 볼트를 장착합니다.
    90 Nm (66.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E18
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 구멍이 정렬되도록 배치합니다.
  8. LH FDU 마운트 볼트를 장착합니다.
    85 Nm (62.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx E18
    Informational PurposesAn informational icon, calling your attention
    참고
    HCU 브래킷의 구멍을 통해 접근합니다.
  9. 언더호이스트 스탠드를 내려 치웁니다.
  10. RH 마운트 볼트(2개)를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 2개, E14
    Informational PurposesAn informational icon, calling your attention
    참고
    최전방 볼트 2개를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    토크: 35Nm +55도
    Informational PurposesAn informational icon, calling your attention
    참고
    이 시점에서 하부 볼트를 규격 토크로 조입니다.
  11. 인버터 냉각수 리턴 호스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스프링 클립 1개
  12. NVH 커버를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼 앤 소켓 클립 2개
  13. 냉각 팬 모듈을 장착합니다. 참조 항목: Module - Cooling Fan (Remove and Install).
  14. 전면 페시아를 장착합니다. 참조 항목: Front Fascia (Remove and Install).
  15. 전면 중앙 아플리케를 장착합니다. 참조 항목: Front Center Applique Assembly (Remove and Install).
  16. 전면 에어로 실드를 장착합니다. 참조 항목: Aeroshield - Front (Remove and Install).
  17. 하단 밸런스를 차체에 고정하는 볼트(6개)를 장착합니다.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    클립 2개, 커버 2개
    Informational PurposesAn informational icon, calling your attention
    참고
    커버(2개)를 고정합니다.
  18. 프렁크 어셈블리를 장착합니다. 참조 항목: Frunk Assembly (Remove and Install).
  19. MV 전원을 다시 연결합니다. 참조 항목: Disconnect MV Power.
  20. 냉각 시스템 진공 재충전을 수행합니다. 참조 항목: 냉각 시스템(진공 보충).
  21. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
  22. 전동식 프렁크를 닫습니다.
  23. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  24. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.