2026-07-02

Seat Assembly - 2nd Row (Remove and Replace)

교정 코드 13050401201 13050401202 FRT 1.74 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Cybertruck의 전자 장치는 효율성을 개선하기 위해 설계된 48V "중간 전압(MV)" 아키텍처로 구동됩니다. MV 구성품을 정비할 때는 부상 및/또는 차량 손상을 피하기 위해 추가적인 지식과 주의가 필요합니다. 전기 사전 주의 사항의 MV 사전 주의 사항을 읽고 이해하며 해당하는 경우 필요한 MV 관련 교육 과정을 이수했는지 확인합니다.
  • 2026-06-12: Released new procedure.

탈거

  1. Open all four doors
  2. Lower all four windows
  3. Manually latch all doors to prevent lockout
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage latch with screwdriver
  4. Enter Service Mode. See 정비 모드.
  5. Raise and move LH front seat forward
  6. Move RH front seat forward
  7. Disconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  8. Close LH and RH visors and retract LH and RH windshield shade assemblies
  9. Remove the LH and RH 2nd row seatback shoulder covers. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  10. Remove the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  11. Release all connections from charge port ecu
    Informational PurposesAn informational icon, calling your attention
    참고
    3x connectors
  12. Remove charge port ECU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolts, 10 mm, 5 Nm, 2x tabs
  13. Release 2nd row center retractor from 2nd LH row buckle
    Informational PurposesAn informational icon, calling your attention
    참고
    Push red release mechanism to release retractor
  14. Remove bolts securing 2nd row seat back onto the back wall
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  15. Remove bolts securing lower 2nd row full seat assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    참고
    8x bolts, 15mm, 50 Nm
  16. Remove bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 15mm, 40 Nm
  17. Remove bolts securing 2nd row seat assembly onto vehicle structural frame
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 15mm, 50 Nm
  18. Remove LH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, 1x datum
  19. Release RH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, 1x datum
  20. Release 2nd row center seat belt from 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x button
  21. Remove 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance

장착

  1. Install 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    Assistance recommended for safe installation onto frame
  2. Install 2nd row center seat belt onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x button
  3. Install RH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, 1x datum
  4. Install LH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, 1x datum
  5. Install bolts securing 2nd row seat assembly onto vehicle structural frame
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 15mm, 50 Nm
  6. Install the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  7. Install bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 15mm, 40 Nm
  8. Install bolts securing lower 2nd row full seat assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    참고
    8x bolts, 15mm, 50 Nm
  9. Install bolts securing 2nd row seat back assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  10. Secure 2nd row center retractor onto 2nd LH row buckle
    Informational PurposesAn informational icon, calling your attention
    참고
    Push red release mechanism to release retractor
  11. Install charge port ECU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10 mm, 5 Nm, 2x tabs, Align charge port ecu into cavity for installation
  12. Secure all connections to charge port ecu connectors
    Informational PurposesAn informational icon, calling your attention
    참고
    3x connectors
  13. Reinstall all components that were removed for access. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  14. Connect mid-voltage power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  15. Move RH front seat to original position
  16. Lower and move LH front seat to original position
  17. Exit Service Mode. See 정비 모드.
  18. Raise all four windows.
  19. Close all four doors.