2025-10-08

Crossbars (Install) (Installation)

교정 코드 61010011 0.30 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

장착

  1. Open the LH rear roof applique door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Plastic trim tool
    그림 1. LH shown; RH similar
    그림 2. LH shown; RH similar
    그림 3. LH shown; RH similar
  2. Remove the nuts (x2) from the vehicle body studs located in the LH rear roof applique door area.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 코드리스 래칫/임팩트 드라이버
    그림 4. LH shown; RH similar
  3. Position the bracket in the LH rear roof applique door area, and then install the nuts (x2) that attach the bracket to the vehicle body studs.
    7.8 Nm (5.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the bracket is positioned with the "OUT" indicator arrow pointed towards the outside of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치
    그림 5. LH shown; RH similar
  4. Repeat step 1 through step 3 for the RH rear roof applique.
  5. Open the LH front sail applique door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Plastic trim tool
    그림 6. LH shown; RH similar
    그림 7. LH shown; RH similar
    그림 8. LH shown; RH similar
  6. Remove the nuts (x2) from the vehicle body studs located in the LH front sail applique door area.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 코드리스 래칫/임팩트 드라이버
    그림 9. LH shown; RH similar
  7. Position the bracket in the LH front sail applique door area, and then install the nuts (x2) that attach the bracket to the vehicle body studs.
    7.8 Nm (5.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the bracket is positioned with the "OUT" indicator arrow pointed towards the outside of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치
    그림 10. LH shown; RH similar
  8. Repeat step 5 through step 7 for the RH rear sail applique.
  9. Install the crossbar on the LH and RH rear roof appliques.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that the front indicator arrow (located in the center of the crossbar) is pointed towards the front of the vehicle.
    그림 11. Crossbar front indicator arrow
    1. Place the LH side of the crossbar in the LH rear roof applique door area.
    2. Carefully extend the crossbar across the vehicle and place the RH side of the crossbar in the RH rear roof applique door area.
    3. Use the key to open the LH side of the crossbar.
      그림 12. LH shown; RH similar
      그림 13. LH shown; RH similar
    4. Align the bottom edges of the LH side of the crossbar with the LH rear roof applique.
      Informational PurposesAn informational icon, calling your attention
      참고
      Make sure that the crossbar is flush against the applique mating surface.
      그림 14. LH shown; RH similar
    5. Close the LH side of the crossbar and use the key to secure the crossbar to the vehicle.
      Informational PurposesAn informational icon, calling your attention
      참고
      An audible click will sound when the crossbar edge is fully secured.
      그림 15. LH shown; RH similar
      그림 16. LH shown; RH similar
    6. Perform a push-pull test on the LH side of the crossbar. If the crossbar edge is loose, repeat step 9.c through step 9.f until the edge is properly secured.
    7. Perform step 9.c through step 9.f for the RH side of the crossbar.
  10. Perform step 9 to install the crossbar on the LH and RH front sail appliques.