2026-04-17

Stud Plate - Hinge - Upper - Door - Rear - LH (Remove and Install)

교정 코드 NEW 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Cybertruck의 전자 장치는 효율성을 개선하기 위해 설계된 48V "중간 전압(MV)" 아키텍처로 구동됩니다. MV 구성품을 정비할 때는 부상 및/또는 차량 손상을 피하기 위해 추가적인 지식과 주의가 필요합니다. 전기 사전 주의 사항의 MV 사전 주의 사항을 읽고 이해하며 해당하는 경우 필요한 MV 관련 교육 과정을 이수했는지 확인합니다.
  • 2026-03-31: Released new procedure.
  1. Remove the LH rear door window regulator. See Window Regulator - Rear Door - LH (Remove and Install).
  2. Apply masking tape around the LH upper rear door hinge
  3. Use a floor jack to support the LH rear door.Raise the jack until it contacts the door.
    Informational PurposesAn informational icon, calling your attention
    참고
    Place a folded microfiber towel or rubber pad between jack pad to protect the door.
  4. Remove LH rear door upper hinge plate
    Informational PurposesAn informational icon, calling your attention
    참고
    2x nuts, 10mm, 10Nm, 1x nut, 15mm, 38Nm
  5. Install LH upper rear door hinge plate and remove tape
    Informational PurposesAn informational icon, calling your attention
    참고
    2x nuts, 10mm, 10Nm, 1x nut, 15mm, 38Nm
  6. Install LH rear door closeout panel
    Informational PurposesAn informational icon, calling your attention
    참고
    11x bolts, 8mm, 4 Nm, 2x bolts,10mm, 12 Nm, 2x grommets
  7. Secure LH rear door harness onto close out panel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips, 4x connectors
  8. Connect external window switch
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  9. Install LH rear door glass
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 4 Nm, Torque at later step, Make sure to properly secure onto regulator mount
  10. Manually unlatch LH rear door
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull on the emergency cable to unlatch, If applicable
  11. MV 전원을 다시 연결합니다. 참조 항목: Mid-Voltage Power (Disconnect and Connect) (Modify).
  12. LH 후면 도어를 엽니다.
  13. Check LH rear door gap and flushness
    Informational PurposesAn informational icon, calling your attention
    참고
    Verify door alignment, and adjust if needed.
  14. Check gap and flushness of LH rear window
  15. Open LH rear door
    Informational PurposesAn informational icon, calling your attention
    참고
    Push LH C-pillar door trigger to release
  16. Torque bolts securing LH rear window to regulator
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 13 Nm
  17. Disconnect external window switch
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  18. Install the LH rear door inner waist belt seal. See Waist Belt Seal - Inner - Rear Door - LH (Remove and Install).
  19. Install the LH rear door trim. See Panel - Door Trim - Rear - LH (Remove and Install).
  20. Install the LH rear door beltline assembly. See Beltline Assembly - Door Panel - Rear - LH (Remove and Install).
  21. Raise LH rear window and close the LH doors.