교정 코드 NEW 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open LH front door
   참고

   Push LH B-pillar door trigger to release
2. Lower LH front window
3. Raise and support vehicle
   참고

   Set air suspension to "Jack Mode"

   

   

4. ODIN 루틴 실행 PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
5. Unlock vehicle gateway
   참고

   After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information

   

   

   

6. Open tailgate
   참고

   Press button to release

   

7. Remove fastener covers from bed floor assembly
   참고

   14x covers

   

   

   

   

   

8. Remove bed floor assembly
   참고

   10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance

   

   

   

   

9. Open powered front trunk
   참고

   Via exterior switch or UI

   

   

10. Remove rear underhood apron
    참고

    9x clips

    

    

11. Disconnect FRL connector then disconnect MV battery connector
    참고

    2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules

    

    

    

12. Raise vehicle fully
    참고

    Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting

    

    

13. Remove rear skid plate
    참고

    6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm

    

    

    

    

    

14. Position coolant drain below rear inverter

    

15. Remove RDU supply hose from exchanger
    참고

    1x spring clip

    

16. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

17. Position coolant catcher below rear drive unit

    

18. Release acoustic cover surrounding RH motor mount
    참고

    5x clips, if acoustic cover is present on mount, remove and discard

    

    

    

19. Remove RDU supply hose from rear inverter
    참고

    1x spring clip, Plug both ends after disconnecting

    

20. Remove RDU supply hose
    참고

    1x clip

    

    

21. Install RDU supply hose
    참고

    1x clip

    

    

22. Install rear inverter coolant supply hose to inverter
    참고

    1x spring clip, Remove plugs from both ends, Perform push-pull test

    

23. Remove coolant catcher from below vehicle
24. Secure RH side acoustic cover
    참고

    5x clips, Secure above clips and remaining from below

    

    

25. Raise vehicle fully
26. Position coolant drain below rear inverter

    

27. Install RDU supply hose from exchanger
    참고

    1x spring clip, Perform push-pull test

    

28. Remove coolant drain container from underneath vehicle
29. Install rear skid plate
    참고

    6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm, Apply Loctite 222 to mid aero shield bolts and install fasteners

    

    

    

    

    

30. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
31. Connect FRL connector then connect MV battery connector
    참고

    2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down

    

    

    

32. ODIN 루틴 실행 PROC_EGGRIGHT3_X_THERMAL-FILL-DRAIN-STOPvia Service Mode:
    • Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    via Toolbox:(link)
33. Install bed floor assembly
    참고

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

    

    

    

    

    

34. Install fastener covers onto bed floor assembly
    참고

    14x covers

    

    

    

    

35. Close tailgate
36. Raise LH front window
37. Close LH front door