2025-10-08

Tailgate Torsion Rod (Remove and Install)

교정 코드 1133116111, 1133116112 0.48 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-06-04: Added steps for bracket/alignment bolts.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

탈거

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. 테일게이트를 엽니다.
  3. 적재함 커버를 닫습니다.
  4. Remove the tailgate assembly from the vehicle. See Tailgate Assembly (Remove and Install).
  5. Remove the tailgate inner cover. See Cover - Inner - Tailgate (Remove and Install).
  6. Loosen the bolt that secures the tailgate torsion rod to the tailgate assembly, but do not remove the bolt from the assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
  7. Remove the tailgate torsion rod from the tailgate assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Note the orientation of the flat edge on the torsion rod.

장착

  1. Torque the bolt that secures the tailgate torsion rod bracket to the tailgate assembly.
    50 Nm (36.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    The bracket bolt must be torqued down to ensure proper torsion rod alignment.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not remove the bolt.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 15mm 소켓
  2. Install the tailgate torsion rod into the tailgate assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the flat edge is in the correct orientation, and then gently tap the rod with a hammer until it is in position.
  3. Torque the bolt that secures the tailgate torsion rod to the tailgate assembly.
    75 Nm (55.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    The bracket bolt must be torqued down to ensure proper torsion rod alignment.
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not remove the bolt.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 13mm 소켓
  4. Install the tailgate assembly into the vehicle. See Tailgate Assembly (Remove and Install).
  5. 적재함 커버를 닫습니다.
  6. 테일게이트를 닫습니다.
  7. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.