2026-03-30

Tire - Front - LH (Tire Purchase)

교정 코드 34021002 FRT 0.35 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
휠 밸런서나 타이어 교환기 작동을 수행하기 전에 타이어 장비 운영자 설명서 및 온스크린 지침을 항상 숙독하고 숙지해야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
항상 휠을 올바르게 고정하고, 사용 중에는 아무도 움직이는 부품 가까이에 접근하지 않는지 확인하십시오. 또한 머리카락, 장신구 및 옷이 움직이는 부품에 걸리지 않도록 하십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차를 수행할 때는 절단 방지 장갑 및 보안경을 포함한 적절한 개인 보호 장비(PPE)를 착용하십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
기계는 한 번에 한 명이 작동해야 합니다. 기계 사용 중 다른 사람은 장비로부터 최소 3피트의 안전 거리를 유지해야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
장비 운영자 설명서에 따라 결함이 있거나 예상대로 작동하지 않는 장비는 사용하지 마십시오.

탈거

  1. 휠 어셈블리를 탈거합니다. 참조 항목: 휠 어셈블리(탈거 및 장착).
  2. 휠과 타이어를 타이어 기계에 놓고 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    휠 클램프 1개
  3. 밸브 스템 캡을 탈거합니다
  4. 밸브 스템 코어를 밸브 코어 탈거 공구를 사용하여 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어에서 공기가 빠르게 빠지므로 주의하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    개인 보호 장비(PPE)로 보안경을 착용합니다.
  5. 상단 롤러가 밸브 스템 전면 약 100mm에 있도록 휠과 타이어를 회전합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    밸브 스템을 적절하게 배치하지 않으면 TPMS 센서가 손상될 수 있습니다.
  6. 상단 비드를 깨트립니다.
  7. 휠에서 타이어를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    TPMS 센서가 타이어 기계 암 앞에 위치하도록 하십시오.

장착

  1. 양쪽 타이어 비드에 윤활유를 충분히 도포한 다음 장착 위치를 정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    TPMS 센서가 타이어 기계 암 반대편에 위치하도록 하십시오. 타이어의 휠 커버 디자인 측이 바깥쪽을 향하도록 합니다.
  2. 타이어를 휠에 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    비드가 손상되지 않도록 주의하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    필요에 따라 추가로 윤활합니다.
  3. 타이어에 공기를 주입하여 비드를 안착시킵니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 사이드월에 표시한 압력을 초과하지 마십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    개인 보호 장비(PPE)로 보안경을 착용합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    내부 및 외부 비드가 안착되었는지 확인합니다.
  4. 밸브 코어 탈거 공구를 사용하여 밸브 코어 스템을 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    손으로만 조입니다. 너무 세게 조이지 마십시오.
  5. 타이어 교환기에서 휠과 타이어를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    클램프 1개
  6. 밸런서에 타이어와 휠 어셈블리를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    6-러그 휠 플랜지 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    휠을 스핀들 샤프트에 배치한 다음 플랜지를 사용하여 휠을 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    6-러그 휠 플랜지를 사용할 수 없는 경우 216mm 블루 헌터 센터링 콘 어댑터를 사용하십시오.
  7. 휠 웨이트를 탈거합니다.
  8. 타이어 공기압이 설정되었는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    운전석 B필러에 부착된 "타이어 및 적재 정보" 라벨을 참조하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    그 후 밸브 스템 캡을 장착합니다.
  9. 밸런서 기계에 휠 치수를 입력합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기계에 수동 입력이 필요하지 않은 경우 이 단계를 건너뜁니다.
  10. 로드 포스 휠 밸런스를 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기계의 지침을 따릅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸런싱을 시작하려면 안전 후드를 내려야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로드 롤러가 제대로 체결되는지 확인하십시오.
  11. 로드 포스 휠 밸런스 결과를 기록합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로드 포스가 한계 내에 있는 경우 휠 웨이트 장착을 건너뜁니다. 로드 포스가 한계를 벗어난 경우,포스 매칭을 진행해야 합니다.
  12. 타이어 및 휠 포스 매칭을 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    런아웃을 측정한 다음 타이어와 림에 참조점을 표시합니다. 기계를 사용하여 타이어와 휠이 매칭되는 지점을 찾습니다.
  13. 밸런서에서 타이어와 휠 어셈블리를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    6-러그 휠 플랜지 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    플랜지를 탈거한 다음 스핀들 샤프트에서 휠을 탈거합니다.
  14. 타이어 및 휠 어셈블리를 타이어 기계에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    휠 클램프 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    휠을 휠 지지대에 배치한 다음 클램프를 사용하여 휠을 고정합니다.
  15. 밸브 스템 캡을 탈거합니다
    Informational PurposesAn informational icon, calling your attention
    참고
    캡 1개
  16. 밸브 스템 코어를 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어에서 공기가 빠르게 빠지므로 주의하십시오. 적절한 PPE를 착용하십시오.
  17. 타이어 비드를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    타이어와 휠 주위에 윤활제를 사용합니다. 상단과 하단 비드를 분리합니다.
  18. 휠에서 타이어를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    TPMS 센서가 타이어 기계 암 앞에 위치하도록 하십시오.
  19. 타이어를 휠에 장착하여 밸런서에서 미리 표시한 지점과 맞춥니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    타이어를 회전하여 이전에 표시한 참조점과 맞춥니다.
  20. 타이어에 공기를 주입하여 비드를 안착시킵니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 작업자의 도움을 받는 것이 좋습니다. 타이어에 공기를 넣으면서 들어올립니다. 타이어 사이드월에 표시한 압력을 초과하지 마십시오.
  21. 밸브 스템 코어를 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어에서 공기가 빠르게 빠지므로 주의하십시오. 적절한 PPE를 착용하십시오.
  22. 타이어 기계에서 타이어 및 휠 어셈블리를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    휠 클램프 1개
    Informational PurposesAn informational icon, calling your attention
    참고
    클램프를 탈거한 다음 휠을 휠 지지대에서 탈거합니다.
  23. 밸런서에 타이어와 휠 어셈블리를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    6러그 휠 플랜지 1개.
    Informational PurposesAn informational icon, calling your attention
    참고
    휠을 스핀들 샤프트에 배치한 다음 플랜지를 사용하여 휠을 고정합니다.
  24. 타이어 공기압이 설정되었는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    운전석 B필러에 부착된 "타이어 및 적재 정보" 라벨을 참조하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸브 스템 캡을 장착합니다.
  25. 밸런서 기계에 휠 치수를 입력합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기계에 수동 입력이 필요하지 않은 경우 이 단계를 건너뜁니다.
  26. 로드 포스 휠 밸런스를 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기계의 지침을 따릅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸런싱을 시작하려면 안전 후드를 내려야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로드 롤러가 물려 있는지 확인합니다.
  27. 휠에 웨이트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸런서에 표시된 위치에 웨이트를 놓습니다.
  28. 스핀 점검을 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기계의 지침을 따릅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밸런싱을 시작하려면 안전 후드를 내려야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로드 롤러가 물려 있는지 확인합니다.
  29. 밸런서에서 타이어와 휠 어셈블리를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    6러그 휠 플랜지 1개.
    Informational PurposesAn informational icon, calling your attention
    참고
    플랜지를 탈거한 다음 스핀들 샤프트에서 휠을 탈거합니다.
  30. 휠 어셈블리를 장착합니다. 참조 항목: 휠 어셈블리(탈거 및 장착).