교정 코드 17103200101, 17103200102 0.66 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open LH front door
   참고

   Push LH B-pillar door trigger to release

   

   

2. Lower LH front window

   

3. Raise and support vehicle
   참고

   Set air suspension to "Jack Mode"

   

   

4. Open tailgate
   참고

   Press button to release

   

5. Open powered front trunk
   참고

   Via exterior switch or UI

   

   

6. Remove rear underhood apron
   참고

   9x clips

   

   

7. Power down vehicle via UI
   참고

   Verify EPBs are engaged, Select charge port icon to ensure drive state is disengaged then power down vehicle via Controls > Safety > Power Off

   

8. Disconnect FRL connector then disconnect MV battery connector
   참고

   2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules

   

   

   

9. Remove fastener covers from bed floor assembly
   참고

   14x covers

   

   

   

   

   

10. Remove bed floor assembly
    참고

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance

    

    

    

    

11. Disconnect rear steering actuator connector
    참고

    1x connector, Release locking tab, 1x harness clip, Place harness aside for access

    

12. Remove RH rear wheel cap
    참고

    1x cap, 8x clips, Use both hands to firmly pull wheel cap to release clips, Cap may remove with or without mounting ring attached

    

    

    

    

13. Loosen RH rear wheel nuts
    참고

    6x nuts, 21mm, 205 Nm

    

14. Raise vehicle partially and lower onto locks
    참고

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

15. Remove RH rear wheel
    참고

    6x nuts, 21mm, 205 Nm

    

16. Remove rear skid plate
    참고

    6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm

    

    

    

    

    

17. Remove rear steer jumper harness
    참고

    1x connector, 4x clips, Release locking tab

    

    

18. Install rear steer jumper harness
    참고

    1x connector, 4x clips, Engage locking tab

    

    

19. Install rear skid plate
    참고

    6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm, Apply Loctite 222 to mid aero shield bolts and install fasteners

    

    

    

    

    

20. Install RH rear wheel
    참고

    6x nuts, 21mm, 205 Nm

    

21. Lower vehicle until tires are touching the ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

22. Install rear steering actuator connector
    참고

    1x connector, Secure locking tab, 1x harness clip, Position harness into place for installation

    

23. Install bed floor assembly
    참고

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

    

    

    

    

    

24. Install fastener covers onto bed floor assembly
    참고

    14x covers

    

    

    

    

25. Torque RH rear wheel nuts
    참고

    6x nuts, 21mm, 205 Nm, Use star pattern

    

26. Install RH rear wheel cap
    참고

    1x cap, 8x clips, Partially secure wheel cap to wheel, While partially installed wheel cover can be rotated to align with tire design, When aligned press inward from center of cap then secure all clips to mounting ring

    

    

    

27. Connect FRL connector then connect MV battery connector
    참고

    2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down

    

    

    

28. Install rear underhood apron
    참고

    9x clips, Adjust windshield seal as required

    

    

29. Close powered front trunk
    참고

    Via exterior switch or UI

    

30. Close tailgate

    

31. Remove vehicle from lift
    참고

    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"

    

    

32. Raise LH front window

    

33. Close LH front door