교정 코드 1220126006 1.26 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open tonneau cover
   참고

   Press forward arrow on LH bed rail

   

2. Open tailgate
   참고

   Press button to release

   

3. Remove tailgate top applique
   참고

   10x clips, 2x guide datums, 5x hooks, replace with a new applique if removed

   

   

   

   

   

4. Remove LH sail applique
   참고

   9x clips, 6x double-sided tape strips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip, Remove double-sided tape from applique and bed side, Remove any remaining adhesive with IPA wipes, Discard sail applique after removal

   

   

   

   

   

5. Remove LH tonneau water management seal
   참고

   1x clip, Pull away from rail to release from groove

   

   

6. Remove the LH sail applique corner bracket
   참고

   1x bolt, 10mm, 9 Nm, 1x datum

   

   

   

7. Remove LH tonneau rail
   참고

   9x bolts, 10mm, 9 Nm, Lift upwards and slide rearwards to release

   

   

   

   

   

8. Remove LH tail lamp step bracket
   참고

   1x clip, 1x bolt, 10mm, 10 Nm, Early production vehicles may not have push clip

   

9. Remove RH sail applique
   참고

   9x clips, 6x double-sided tape strips, Remove double-sided tape from applique and bed side, Remove any remaining adhesive with IPA wipes, Discard sail applique after removal

   

   

   

10. Remove RH tonneau water management seal
    참고

    1x clip, Pull away from rail to release from groove

    

    

11. Remove the RH sail applique corner bracket
    참고

    1x bolt, 10mm, 9 Nm, 1x datum

    

    

    

12. Remove RH tonneau rail
    참고

    9x bolts, 10mm, 9 Nm, Lift upwards and slide rearwards to release

    

    

    

    

    

13. Remove RH tail lamp step bracket
    참고

    1x clip, 1x bolt, 10mm, 10 Nm, Early production vehicles may not have push clip

    

14. Measure the slot length on inner sail stamping
    참고

    if slot length is shorter than 23mm then proceed with rework steps to elongate holes

    

15. Perform rework on both LH and RH inner sail stamping to elongate holes
    참고

    16x holes, 8 holes on each side, Hole needs to be elongated 2 mm per side to allow for float, Scribe each hole using a caliper and filed it out by hand, Rework only apply for built date before 4/12/2024, Proceed onto next step if built afterwards

    

    

    

    

    

    

    

16. Apply a coat of SEM self-etching primer to reworked areas
    참고

    16x reworked holes, Allow time for primer to dry

    

    

17. Install RH tail lamp step bracket
    참고

    1x clip, 1x bolt, 10mm, 10 Nm, Early production vehicles may not have push clip

    

18. Position RH tonneau rail and sail applique corner bracket into place

    

    

    

    

19. Install RH tonneau rail
    참고

    9x bolts, 10mm, 9 Nm, Maneuver rail into position, Fasteners may vary, if needed add new bolt to secure RH sail applique corner bracket into place

    

    

    

    

    

    

20. Install RH tonneau water management seal
    참고

    1x clip, Push seal into rail groove

    

    

21. Install RH sail applique
    참고

    17x clips, 1x datum, Verify the forward most clips are present and seated correctly Align RH sail applique into position, Ensure all clips are properly secured onto body, Failure to secure clips could result in part ejection

    

    

    

    

    

22. Install LH tail lamp step bracket
    참고

    1x clip, 1x bolt, 10mm, 10 Nm, Early production vehicles may not have push clip

    

23. Position LH tonneau rail and sail applique corner bracket into place

    

    

    

    

24. Install LH tonneau rail
    참고

    9x bolts, 10mm, 9 Nm, Maneuver rail into position, Fasteners may vary, if needed add new bolt to secure applique corner bracket into place

    

    

    

    

    

    

25. Install LH tonneau water management seal
    참고

    1x clip, Push seal into rail groove

    

    

26. Install LH sail applique
    참고

    17x clips, 1x datum, 1x connector, 1x harness clip, Verify the forward most clips are present and seated correctly, Align LH sail applique into position, Ensure all clips are properly secured onto body, Failure to secure clips could result in part ejection

    

    

    

    

    

    

27. Install tailgate top applique
    참고

    10x clips, 2x guide datums, 5x hooks, Align hooks and swing rear wards, Wrap a mallet with a microfiber to ensure hooks are engaged fully

    

    

    

    

    

    

    

28. Close tailgate

    

29. Close tonneau cover