교정 코드 11200101601 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open all four doors
   참고

   Push pillar door triggers to release
2. Lower all four windows
3. Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
4. Raise and move LH front seat forward
5. Move RH front seat forward
6. Open powered front trunk
   참고

   Via exterior switch or UI

   

   

7. Power off vehicle from center display
   참고

   Verify EPBs are engaged, Select charge port icon to ensure drive state is disengaged then power down vehicle via Controls > Safety > Power Off

   

8. Remove rear underhood apron
   참고

   9x clips

   

   

9. Disconnect first responder loop and MV battery connector
   참고

   2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules

   

   

   

10. Remove front header trim
    참고

    19x clips, 1x magnet, 1x connector, 1x harness clip

    

    

    

11. Remove LH mid A-pillar trim
    참고

    1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip

    

    

    

12. Remove LH IP quarter panel
    참고

    3x large clips, 3x small clips, 2x datums, 3x doghouses, Release small inner clips then locate doghouses, Break doghouse walls to release from panel, Remove panel then remove doghouses and clips, Protect IP as needed, If IP is damaged then proceed to replacement, Panel is single use, Discard after removal

    

    

    

    

    

    

    

13. Remove LH upper A-pillar panel
    참고

    8x clips, 1x tether clip, 1x harness clip, 1x connector, 1x bolt, 10mm, 6 Nm, Pull inwards to release, Depress tabs on either side of tether clip to release, Apply tape onto top pad to prevent damage

    

    

    

    

    

    

14. Remove rear header trim
    참고

    12x clips, 3x datums

    

    

15. Remove LH lower C-pillar trim
    참고

    3x clips, 7x tabs, 4x datums, Starting at door sill pull upward then forward to release, Leave trim attached to seat belt

    

    

    

16. Remove LH cantrail trim panel
    참고

    5x clips, 1x connector, 1x tab, 3x bolts, T30, 6 Nm, Release clips then allow cantrail to hang from tethers for access to fasteners

    

    

    

    

17. Remove LH cantrail trim panel
    참고

    5x clips, 1x connector, 3x bolts, T30, 6 Nm, Release clips then allow cantrail to hang from tethers for access to fasteners

    

    

    

    

    

18. Remove LH 2nd row shoulder cover
    참고

    7x clips, 1x datum

    

    

    

19. Remove 2nd row seatback LH outboard bolster
    참고

    2x tabs, 1x datum, 3x clips, Release tab near the bottom of LH outboard bolster, Partially release LH 2nd row shoulder cover and remove bolster from vehicle

    

    

    

    

    

    

    

    

20. Remove LH C-pillar upper trim
    참고

    5x clips, 3x tabs

    

    

    

21. Remove interior fasteners securing lower tonneau assembly
    참고

    2x bolts, 13mm, 20 Nm

    

    

22. Remove fastener covers from bed floor assembly
    참고

    14x covers

    

    

    

    

    

23. Remove bed floor assembly
    참고

    12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance

    

    

    

    

24. Remove LH bed closeout panel
    참고

    6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle

    

    

    

    

25. Remove LH lower bed side wall
    참고

    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 3x connectorsRelease locking tabs, Disconnect bed outlet connectors from bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Release locking tabs, Slide lock to release.

    

    

    

    

    

    

    

    

    

    

26. Remove RH bed closeout panel
    참고

    6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle

    

    

    

    

27. Remove RH bed side wall
    참고

    1x bolt, 15mm, 46 Nm, 2x bolts, T40, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Release locking tabs

    

    

    

    

    

    

    

    

    

28. Remove false wall
    참고

    2x bolts, 15mm, 45 Nm. Recommended to use assistance to prevent scratching bed liner

    

    

    

29. Remove fasteners securing RH tonneau NVH barrier
    참고

    6x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover*part number for bolts needed

    

    

    

30. Remove RH tonneau NVH barrier
    참고

    Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then remove

    

    

    

    

    

    

31. Remove fasteners securing LH tonneau NVH barrier
    참고

    5x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover

    

    

    

32. Remove LH tonneau NVH barrier
    참고

    Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then remove

    

    

    

    

    

    

33. Remove two rear tonneau square profile support braces
    참고

    8x screws, T30, 5 Nm, 2x support braces, Remove two square support braces that are closest to rear of vehicle, Remove bolts at each end of support braces, Slide braces off of mounting points on flat cassette assemblies, Braces slide off in same direction of fasteners, maneuver each brace out of bed opening (*Note: No part number provided for the screws, they come with the square profile brace)

    

    

34. Remove front tonneau cover box cross supports
    참고

    8x screws, T25, 5 Nm

    

    

35. Remove tonneau applique
    참고

    2x bolts, T30, 9 Nm, Remove bolts then firmly pull upward from rear edge of applique to release rear of applique, Depress locking tab on forward mounting points to release

    

    

    

    

    

36. Remove LH backlight applique assembly
    참고

    2x clips, 1x adhesive strip, Cut adhesive then pry inward to release

    

    

    

37. Remove LH tonneau motor
    참고

    1x connector, 2x bolts, 10mm, 11 Nm

    

    

    

    

    

38. Remove lower tonneau brackets
    참고

    2x nuts, 13mm, 30 Nm, 1x bolts, 13mm, 30 Nm

    

    

39. Remove lower tonneau assembly fasteners
    참고

    1x nut, 10mm, 6 Nm, 1x bolt, 10mm, 6 Nm, 1x bolt, 13mm, 20 Nm

    

    

40. Remove LH tonneau flat cassette assembly
    참고

    Lift upwards to release from datum on back wall

    

    

41. Install LH tonneau flat cassette assembly
    참고

    Engage datum at back wall

    

    

42. Install LH tonneau flat cassette fasteners
    참고

    1x nut, 10mm, 6 Nm, 1x bolt, 10mm, 6 Nm, 1x bolt, 13mm, 20 Nm

    

    

43. Install LH lower tonneau bracket
    참고

    2x nuts, 13mm, 30 Nm, 1x bolts, 13mm, 30 Nm

    

    

44. Install LH tonneau motor
    참고

    1x connector, 2x bolts, 10mm, 11 Nm

    

    

    

    

45. Instal LH backlight applique assembly
    참고

    2x clips, Replace any missing or damaged clips, Install new double sided adhesive

    

    

    

46. Install tonneau applique
    참고

    2x bolts, T30, 9 Nm, Position over mounting points then apply downward pressure to engage front and rear attachment points, Install bolts, Ensure seal is not caught outboard of applique, Use trim tool to adjust seal position as required

    

    

    

    

    

    

47. Install front tonneau cover box cross supports
    참고

    8x screws, T25, 5 Nm

    

    

48. Install two rear tonneau square profile support braces
    참고

    8x screws, T30, 5 Nm, Install two square support braces that are closest to rear of vehicle, Slide notches at each of support brace to mounting points on flat cassette assemblies, Square supports install in the same direction of the fasteners

    

    

49. Position LH tonneau NVH barrier
    참고

    Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then position

    

    

    

    

    

    

50. Install fasteners securing LH tonneau NVH barrier
    참고

    5x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover

    

    

    

51. Position RH tonneau NVH barrier
    참고

    Vehicles built before April 2024 will have 1-piece NVH cover, Vehicles built after April 2024 will have updated 1-piece NVH cover, Vehicles built after October 2024 will have 2-piece NVH cover, Maneuver around bed wall then position

    

    

    

    

    

    

52. Install fasteners securing RH tonneau NVH barrier
    참고

    6x bolts, T25, 5 Nm, Vehicles built before April 2024 will have 1-piece NVH cover, 5x bolts, 8mm, 5 Nm, Vehicles built after April 2024 will have updated 1-piece NVH cover, 9x bolts, 4mm Allen, 5 Nm, Vehicles built after October 2024 will have 2-piece NVH cover

    

    

    

53. Install false wall
    참고

    2x bolts, 15mm, 45 Nm. Recommended to use assistance to prevent scratching bed liner

    

    

    

54. Install RH bed side wall
    참고

    1x bolt, 15mm, 46 Nm, 2x bolts, T40, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Recommend assistance

    

    

    

    

    

    

    

    

55. Install RH bed closeout panel
    참고

    6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle

    

    

    

56. Install LH lower bed side wall
    참고

    1x bolt, 15mm, 46 Nm, 2x bolts, 13mm, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Secure locking tabs, Connect bed outlet connectors onto bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Secure locking tabs, Slide lock to secure, Recommend assistance

    

    

    

    

    

    

    

    

    

57. Install LH bed closeout panel
    참고

    6x clips, 1x tab, Secure LH tailgate cable once closeout installed

    

    

    

58. Install bed floor assembly
    참고

    12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

    

    

    

    

    

59. Install fastener covers onto bed floor assembly
    참고

    14x covers

    

    

    

    

60. Install interior fasteners securing lower tonneau assembly
    참고

    2x bolts, 13mm, 20 Nm

    

    

61. Install LH C-pillar upper panel
    참고

    5x clips, 3x tabs

    

    

    

62. Install 2nd row seatback LH outboard bolster
    참고

    2x tabs, 1x datum, 3x clips, Position LH outboard bolster into place, Ensure all clips and tabs are fully engaged, Replace any missing or damaged clips, Secure LH 2nd row shoulder cover, Perform push-pull-push test

    

    

    

    

    

    

    

63. Install LH 2nd row shoulder cover
    참고

    7x clips, 1x datum

    

    

    

64. Install LH cantrail panel
    참고

    5x clips, 1x connector, 3x bolts, T30, 6 Nm, Secure tethers then secure clips

    

    

    

    

    

65. Secure LH lower C-pillar trim
    참고

    1x clip, 1x datum

    

66. Install LH upper A-pillar panel
    참고

    8x clips, 1x tether clip, 1x edge clip, 1x connector, 1x bolt, 10mm, 6 Nm, Ensure tethers are correctly oriented, Replace any missing or damaged clips, Remove tape as needed

    

    

    

    

    

    

67. Install LH mid A-pillar trim
    참고

    1x clip, 3x tabs, Replace any missing or damaged clips

    

    

    

68. Install rear header trim
    참고

    12x clips, 3x datums, Replace any missing or damaged clips

    

    

69. Install front header trim
    참고

    19x clips, 1x magnet, 1x connector, 1x harness clip, Replace any missing or damaged clips

    

    

    

70. Lower and move LH front seat to original position
71. Move RH front seat to original position
72. Intall the tonneau slats. See Slat System - Tonneau (Remove and Install).
73. Raise all 4 windows
    참고

    Verify switch is operating as expected
74. Close all four doors