2025-10-08

Slat System - Tonneau (Rework) (Modify)

교정 코드 1120122007 FRT 1.20 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-01-23: Added special tools section.
  • 2024-11-26: Corrected note that still referenced adding 2 slats.
  • 2024-10-7: Updated steps to only add 1 slat instead of 2 slats.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Special tools required for this procedure:
  • 1996616-00-ATonneau Bushing Removal Tool
  • 1999662-00-ATonneau Transfer Frame

절차

  1. 적재함 커버를 닫습니다.
  2. Inspect Water Management slat.
    Informational PurposesAn informational icon, calling your attention
    참고
    If any gap is present in the fore/aft space between the tonneau applique and Water Management slat, continue the rework to add 1 slat to close the gap.
  3. Remove the tonneau slat assembly. See Slat System - Tonneau (Remove and Install).
  4. Remove the crosscar fixation tubes (x3).
    Informational PurposesAn informational icon, calling your attention
    참고
    The last tube at the water management slat will be removed at a later step.
  5. Insert 2 inflatable bags under the tonneau slats at the tonneau transfer frame crossbar.
  6. Remove the LH Water Management slat bolts, rollers, and Tonneau Service Kit. Repeat this step for the RH side.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x slat bolts, 2x sleeves, 4x rollers, 1x Y-React Clip. Carefully pull outwards to release slat bolts from slats.
    그림 1. LH shown; RH similar
    그림 2. LH shown; RH similar
  7. Slide the Water Management slat away from the slat assembly to release it, and then remove the Water Management slat from the assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    The chain links will come with the slat.
  8. Remove last link of LH chain. Repeat this step for the RH chain.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bushing. Use special tonneau removal tool to release roller bolt from the chain bushing. Remove the bushing and last chain slat. Discard bushing and use new bushing to lock pin in place. Remove Y-reaction clip and install at a later step at the Water Management Slat.
  9. Re-position Y-reaction clips on LH side of chain. Repeat this step for the RH side of the chain.
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips. Replace any broken clips. Move all clips 1/2 step down to secure last link of chain. Leave top most link open to secure at a later step.
  10. Install one slat onto the front of the tonneau slat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply silicon lubrication onto tonneau sealing slat to ease installation. Position mid slat onto tonneau and slide into place. Ensure slat is properly installed onto tonneau sealing channel.
  11. Install Water Management slat with tonneau chain
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply silicon lubrication onto tonneau sealing slat to ease installation, Position bushing slat to match slat hinge opening, Slide into place
  12. Install RH Mid Slat Roller Tonneau Service Kit to join new slat. Repeat this step for the LH side.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x slat bolts, 2x sleeves, 4x rollers, 1x Y-React Clips. Insert slat bolts into slats until fully engaged.
  13. Install LH Y-reaction clip to Water Management Slat Bolt Roller. Repeat this step for the RH side.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x Y-React Clip. Re-use clip removed from last link of chain at previous step. Ensure clip is fully engaged to both roller pins.
  14. Install fixation tubes
    Informational PurposesAn informational icon, calling your attention
    참고
    3x crosscar fixation tubes, From the Water Management crosscar fixation tube Skip 3 chain bushings for backlite opening when tonneau is closed, Skip 2 chain bushings for next tube then Skip1 chain bushing and install the last tube in the last bushing on the chain
  15. Install the tonneau slat assembly. See Slat System - Tonneau (Remove and Install).
  16. On the vehicle touchscreen, navigate to UI > Closures > Tonneau > Calibrate Tonneau to run the Tonneau Calibration routine.
    Informational PurposesAn informational icon, calling your attention
    참고
    Allow the routine to complete. The tonneau will move while the routine running.
  17. 적재함 커버를 닫습니다.
  18. Confirm there is no gap present between the tonneau cover and the tonneau applique.
    Informational PurposesAn informational icon, calling your attention
    참고
    Confirm no gap present fore/aft and top of slat to bottom of seal.
  19. 정비 모드를 종료합니다. 참조 항목: 정비 모드.
  20. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.