교정 코드 33013325 1.26 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
2. 차량을 들어 올려서 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
3. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
4. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
5. In Toolbox, click the Actions tab, and then search for "EPB enter service mode".
6. Click PROC_EPB_X_SERVICE-MODEvia Service Mode:
   • Chassis ➜ Brakes ➜ EPB Service Mode
   • Chassis ➜ Brakes ➜ EPB Service Mode
   via Service Mode Plus:Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brakevia Toolbox:(link), and then select the following:
   1. EPB Selection: BOTH
   2. Action Selection: START
   3. Click Run and allow the routine to complete.
   참고

   Chock wheel if necessary.

   참고

   Follow the on-screen instructions if necessary.

   참고

   Make sure the routine is successful.
7. Remove all 4 wheel caps and loosen all the wheel nuts. See Wheel Cover - Front - LH (Remove and Install).
8. Raise the vehicle fully.
9. Remove the LH front wheel. See 휠 어셈블리(탈거 및 장착).
10. Remove the bolt that attaches the LH front brake hose bracket to the knuckle.
    

    10 Nm (7.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 딥소켓

    

11. Remove the brake pad anti-rattle springs (x2) from the LH front brake caliper.
    참고

    Release the tab, and then remove the spring from the caliper. Repeat for the remaining anti-rattle spring.

    

    

    

12. Remove the bolts (x2) that attach the LH front caliper to the knuckle, and then set the caliper aside.
    

    315 Nm (232.3 lbs-ft)
    참고

    The rotor will be loose until the caliper is reinstalled. Use lug nut to secure the rotor as needed.

    TIp

    다음 공구 사용을 권장합니다.

    • 24mm 소켓

    

13. Remove the brake pads from the LH front caliper.

    

14. Clean the LH front brake pads.
    참고

    Use a wire brush and pick as needed. Clean any debris from the central groove in the brake pad friction surface.

    

15. Clean the LH front brake caliper.
    참고

    Use a nylon brush and brake cleaner as needed. Allow 1 minute of dry time.

    

16. Clean the LH front brake caliper anti-rattle springs (x2).
    참고

    Use soapy water or brake cleaner as needed. Allow 1 minute of dry time.

    

17. Remove the LH front brake rotor.

    

18. Inspect the inner and outer brake rotor vents and surface for debris, and then clean the rotor as needed.
    참고

    Make sure the rotor mating surface to the hub is clean on the inboard and outboard faces.

    

    

19. Install the LH front brake rotor.
    참고

    The rotor will be loose until the caliper is reinstalled.

    

20. Apply an even layer of Silaramic lubricant onto both LH brake pad guide contact points.

    

    

21. Install the brake pads (x2) into the LH front caliper.

    

22. With assistance, position the LH front caliper onto the knuckle, and then install the bolts (x2) that attach the caliper to the knuckle.
    

    315 Nm (232.3 lbs-ft)
    참고

    The rotor will be loose until the caliper is installed.

    TIp

    다음 공구 사용을 권장합니다.

    • 24mm 소켓

    

23. Install the brake pad anti-rattle springs (x2) into the LH front brake caliper.

    

    

    

24. Install the bolt that attaches the LH front brake hose bracket to the knuckle.
    

    10 Nm (7.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 딥소켓

    

25. Install the LH front wheel onto the vehicle and hand-tighten the lug nuts (x6).
26. Remove the LH rear wheel. See 휠 어셈블리(탈거 및 장착).
27. Release the locking tab, and then disconnect the EPB harness electrical connector from the LH rear brake caliper.

    

28. Remove the bolt that attaches the LH rear brake line to upper control arm, and then release the line from the control arm.
    

    10 Nm (7.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

29. Remove the bolt that attaches the LH rear caliper to the bracket.
    

    40 Nm (29.5 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 14mm 소켓

    

30. Pivot the LH rear caliper upward.

    

31. Remove the LH rear caliper pad return springs (x2).
    참고

    Hold the brake pads, and then remove spring one at a time.

    

    

    

32. Remove the brake pads (x2) from the LH rear caliper bracket.

    

33. Use a wire brush to remove any dust or debris from the LH rear brake pads.

    

34. Clean the LH rear brake caliper and brake pad guide surfaces.
    참고

    Use a nylon brush and brake cleaner as needed. Allow 1 minute of dry time.

    참고

    Make sure to clean both sides of the guides.

    

    

35. Apply an even layer of Silaramic lubricant to the LH rear brake pad contact points and pad guides.

    

    

    

36. Install the brake pads (x2) into the LH rear caliper bracket.
    참고

    Make sure the pads seat correctly onto the guides.

    

37. Install the LH rear caliper pad return springs (x2).
    참고

    Hold the pads, and then install each spring one at a time.

    

    

    

38. Pivot the LH rear caliper downward into position.
    참고

    Hold the pads while pivoting to ensure correct fitment.

    

    

39. Install the bolt that attaches the LH rear caliper to the bracket.
    

    40 Nm (29.5 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 14mm 소켓

    

40. Remove the bolts (x2) that attach the LH rear brake caliper to the knuckle, and then use an S-hook to hang the caliper to the body.
    

    150 Nm (110.6 lbs-ft)
    경고

    Route the caliper hose so that it does not get caught on the stabar assembly.

    참고

    다음 공구 사용을 권장합니다.

    • 21mm 소켓

    

    

41. Remove the LH rear brake rotor.

    

42. Inspect the inner and outer brake rotor vents and surface for debris, and then clean the rotor as needed.
    참고

    Make sure the rotor mating surface to the hub is clean on the inboard and outboard faces.

    

    

43. Position the LH rear brake rotor onto the vehicle.
    참고

    The rotor will be loose until the caliper is reinstalled.

    

44. Position the LH rear brake caliper onto the knuckle, and then install the bolts (x2) that attach the caliper to the knuckle.
    

    150 Nm (110.6 lbs-ft)
    경고

    Route the caliper hose so that it does not get caught on the stabar assembly.

    참고

    다음 공구 사용을 권장합니다.

    • 21mm 소켓

    

45. Position the LH rear brake line to the upper control arm, and then install the bolt that attaches the line to the control arm.
    

    10 Nm (7.4 lbs-ft)
    TIp

    다음 공구 사용을 권장합니다.

    • 10mm 소켓

    

46. Connect the EPB harness electrical connector to the LH rear brake caliper, and then engage the connector lock.

    

47. Install the LH rear wheel, and then install and hand-tighten the lug nuts.
48. Repeat step 9 through step 47 for the RH front and rear brakes.
49. Lower the vehicle until the tires are touching the ground.
50. Press brake pedal, and then select park on the UI to disable EPB service mode.
51. Torque all the wheel nuts and install the all 4 wheel covers. See 휠 어셈블리(탈거 및 장착).
52. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
53. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.