2025-10-03

Center Display Cable Overlay (Repair)

교정 코드 1710029008 0.84 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Cybertruck의 전자 장치는 효율성을 개선하기 위해 설계된 48V "중간 전압(MV)" 아키텍처로 구동됩니다. MV 구성품을 정비할 때는 부상 및/또는 차량 손상을 피하기 위해 추가적인 지식과 주의가 필요합니다. 전기 사전 주의 사항의 MV 사전 주의 사항을 읽고 이해하며 해당하는 경우 필요한 MV 관련 교육 과정을 이수했는지 확인합니다.
  1. Remove lower IP panel. See Lower Assembly - Instrument Panel (Remove and Install).
  2. Remove the glovebox assembly. See Glovebox Assembly (Remove and Install).
  3. Remove the center display assembly. See Touchscreen - Center Display Assembly (Remove and Install).
  4. Disconnect center display cable from car computer
  5. Cut display side of display cable and wrap with tape
    Informational PurposesAn informational icon, calling your attention
    참고
    Refer to cable overlay guidelines: TN-20-17-001
  6. Cut car computer side of display cable and wrap with tape
    Informational PurposesAn informational icon, calling your attention
    참고
    Refer to cable overlay guidelines: TN-20-17-001
  7. Position center display cable onto IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    Refer to cable overlay guidelines: TN-20-17-001
  8. Secure center display cable onto IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    Refer to cable overlay guidelines: TN-20-17-001, cable ties x 15
  9. Connect enter display cable to car computer
  10. Install the center display assembly. See Touchscreen - Center Display Assembly (Remove and Install).
  11. Install the glovebox assembly. See Glovebox Assembly (Remove and Install).
  12. Install lower IP panel. See Lower Assembly - Instrument Panel (Remove and Install).