교정 코드 17101201101 17101201102 2.58 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open LH front door
   참고

   Push LH B-pillar door trigger to release

   

   

2. Lower LH front window

   

3. 차량을 정비 모드로 전환합니다. 참조 항목: 정비 모드.
4. Open LH rear door
   참고

   Push LH C-pillar door trigger to release

   

   

5. Lower LH rear window

   

6. Remove 2nd row floor mat

   

   

7. Open RH front door
   참고

   Push RH B-pillar door trigger to release

   

   

8. Lower RH front window

   

9. Open RH rear door
   참고

   Push RH C-pillar door trigger to release

   

   

10. Lower RH rear window

    

11. Open tailgate
    참고

    Press button to release, Use manual release as necessary

    

12. Open powered front trunk
    참고

    Via exterior switch or UI

    

    

13. Remove rear underhood apron
    참고

    9x clips

    

    

14. Disconnect first responder loop and MV battery connector
    참고

    2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules

    

    

    

15. Remove frunk assembly
    참고

    6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Remove bolt covers from frunk floor, Remove washer fluid cap by gently prying upwards, Rotate bumpstops counter clockwise to release, the 25mm socket from PT Sensor kit can be used, Avoid straining emergency frunk release connector

    

    

    

    

    

    

    

    

    

16. Remove RH underhood apron
    참고

    3x clips

    

    

    

17. Remove front nut securing RH cantrail
    참고

    1x nut, 8mm, 4 Nm, Discard after removal

    

    

18. Remove RH sail baffle applique
    참고

    3x clips, Release clips working from bottom upwards

    

    

19. Remove RH sail baffle closeout
    참고

    6x clips

    

    

    

20. Remove RH C pillar applique closeout
    참고

    2x clips

    

    

21. Remove RH C pillar applique
    참고

    1x connector, 2x clips, 1x bolt, 10mm, 6 Nm, Pull outwards from bottom then pull down to release

    

    

    

    

22. Remove RH header seal
    참고

    Seal begins at front quarter glass and ends at C-pillar applique, Start at C-pillar, Pull B-pillar applique down gently to release seal, Pull outwards to release seal from carrier grooves

    

    

    

    

23. Remove screws securing RH cantrail
    참고

    8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access

    

    

24. Remove RH cantrail assembly
    참고

    7x clips, Recommend assistance, Pull away from body side to release clips, Place on padded surface

    

    

25. Remove RH rear fender flare
    참고

    18x clips

    

    

    

26. Remove clips securing RH rear wheel liner to aft fender flare carrier
    참고

    2x clips

    

27. Remove clips securing RH rear wheel liner to fore fender flare carrier
    참고

    5x clips

    

    

28. Remove RH rear aft fender flare carrier
    참고

    2x bolts, 10mm, 7 Nm

    

    

29. Remove RH rear fore fender flare carrier
    참고

    6x bolts, 10mm, 7 Nm, 1x connector, Disconnect BLE module then remove carrier, Release locking tab

    

    

    

30. Remove fastener covers from bed floor assembly
    참고

    14x covers

    

    

    

    

    

31. Remove bed floor assembly
    참고

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance

    

    

    

    

32. Remove LH lower bed side wall
    참고

    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

    

    

    

    

    

    

    

33. Remove RH sail applique
    참고

    15x clips

    

    

    

34. Remove the RH bed closeout panel
35. Remove RH bed closeout panel
    참고

    6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle

    

    

    

    

36. Remove RH bed side wall
    참고

    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

    

    

    

    

    

    

    

    

    

37. Release RH tail lamp applique
    참고

    2x clips, 2x datums

    

    

38. Remove RH outer bed side
    참고

    13x bolts, 13mm, 28 Nm, 1x screw, T30, 8 Nm, Assistance required, Have assistant hold bed side to body while bolts are removed, Place on padded surface once removed

    

    

    

    

39. Remove RH mid A-pillar trim
    참고

    1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip

    

    

    

40. Remove RH upper A-pillar panel
    참고

    8x clips, 1x harness clip, 1x connector, 1x bolt, 10mm, 6 Nm, Pull inwards to release

    

    

    

    

    

41. Push open RH coat hook
    참고

    Press to release

    

    

42. Remove RH coat hook bolt cover
    참고

    2x tabs

    

    

43. Remove RH coat hook bolt
    참고

    1x bolt, T20, 2.5 Nm

    

44. Remove RH cantrail trim panel
    참고

    5x clips, 1x connector, 3x bolts, T30, 6 Nm, Release clips then allow cantrail to hang from tethers for access to fasteners

    

    

    

    

    

45. Fold up 2nd row 60 seat
    참고

    Pull tether to release then lift up until locked in place

    

46. Partially release LH lower C-pillar trim
    참고

    1x clip, 1x datum

    

47. Fold up 2nd row 40 seat
    참고

    Pull tether to release then lift up until locked in place

    

    

48. Partially release RH lower C-pillar trim
    참고

    1x clip, 1x datum

    

49. Remove rear wall lower trim
    참고

    2x push clips, 4x clips, Remove outermost push clips, then pull straight forward to release inner clips

    

    

    

    

    

50. Remove RH Upper C-pillar
    참고

    5x clips, 3x tabs

    

    

    

51. Release RH 2nd row shoulder cover
    참고

    7x clips, 1x datum

    

    

    

52. Remove clip securing RH 2nd row seat outboard B cover assembly
    참고

    1x clip, Position aside for access to clip

    

    

53. Remove RH 2nd row seat back assembly
    참고

    2x push clips, 4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Pull upwards then away from frame then disconnect electrical harness, Release locking tab

    

    

    

    

    

    

    

    

    

54. Remove LH rear aft fender flare
    참고

    5x clips

    

    

    

55. Remove clips securing LH rear wheel liner onto rear fascia and diffuser
    참고

    5x clips

    

56. Remove clips securing LH rear wheel liner to aft fender flare carrier
    참고

    2x clips

    

57. Remove LH rear aft fender flare carrier
    참고

    2x bolts, 10mm, 7 Nm, 2x datum

    

    

58. Remove license plate
    참고

    4x screws, Phillips PH2, 1 Nm

    

59. Remove bolts securing rear center fascia onto body
    참고

    2x bolts, 10mm, 6 Nm

    

60. Remove clips securing RH rear wheel liner onto rear fascia and diffuser
    참고

    5x clips

    

61. Remove bolts securing rear diffuser onto body
    참고

    9x bolts, 10mm, 6 Nm

    

    

    

62. Disconnect rear fascia harness connector
    참고

    1x connector, Release locking tab, Harness is located behind rear of LH rear wheel liner

    

    

63. Remove rear fascia from vehicle
    참고

    16x tabs, Release RH and LH side of rear fascia from body, Remove rear fascia from vehicle, Recommended assistance, Place onto protected surface

    

64. Remove RH rear wheel liner
    참고

    19x push clips, 5x push nuts, Discard push nuts after removal

    

    

65. Release rear lower section of RH bed harness
    참고

    1x connector, 5x clips, Release clip at opening near rear fascia bracket then pull harness through, Release locking tab

    

    

66. Release rear upper section of RH bed harness
    참고

    2x connectors, 11x clips, Release locking tabs

    

67. Release mid section of RH bed harness
    참고

    8x clips

    

68. Release ancillary section of RH bed harness
    참고

    3x connectors, 3x clips, Disconnect from HV battery ancillary passthrough, Disconnect height sensor, Release locking tabs

    

    

    

69. Release front section of RH bed harness
    참고

    1x connector, 8x clips, 1x bolt, 10mm, 7 Nm, Release locking tab

    

    

70. Release interior section of RH bed harness
    참고

    1x connectors, 12x clips, 1x grommet, 1x bolt, 8mm, 4 Nm, Do not remove locking cover, Loosen until bolt spins freely, Double check that bolt and locking cover are fully released before attempting to release any MV connectors, Depress tabs to release grommet, Release locking tabsPlastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may release crooked causing it to get stuck, secure bolt a few turns to loosen the tension then release bolt while assisting plastic locking cover by gently prying on the side that's stuck Metal Locking Cover You can use power tools, Quickly disconnecting locking cover helps connectors remove symmetrically

    

    

    

71. Remove RH bed harness
    참고

    Pull harness through from interior

    

    

72. Position RH bed harness
    참고

    Push harness through to interior

    

    

73. Secure interior section of RH bed harness
    참고

    1x connector, 12x clips, 1x grommet, 1x bolt, 8mm, 4 Nm, Ensure connectors are aligned before securing bracket, Secure locking cover bolt by hand initially to prevent thread stripping, Secure grommet by pushing inwards, Engage locking tabsPlastic Locking Cover Use hand tools on any plastic locking covers, The locking cover may secure crooked causing it to get stuck, release bolt a few turns to loosen the tension then secure bolt while assisting plastic locking cover by gently pushing on the side that's stuck, Push connectors while driving the locking cover bolt to ensure correct seating Metal Locking Cover You can use power tools, Slowly drive locking cover, Ensure locking cover and bolt are seated fully

    

    

    

74. Secure front section of RH bed harness
    참고

    1x connector, 8x clips, 1x bolt, 10mm, 7 Nm, Engage locking tab

    

    

75. Secure ancillary section of RH bed harness
    참고

    3x connectors, 3x clips, Connect HV battery ancillary passthrough, Connect height sensor, Engage locking tabs

    

    

    

76. Secure mid section of RH bed harness
    참고

    8x clips

    

77. Secure rear upper section of RH bed harness
    참고

    2x connectors, 11x clips, Engage locking tabs

    

78. Secure rear lower section of RH bed harness
    참고

    1x connector, 5x clips, Push harness through opening near rear RH fascia bracket then secure clip, Secure locking tab

    

    

79. Install RH rear wheel liner
    참고

    19x push clips, 5x push nuts, Install new push nuts, Use of a socket and dead blow hammer can aid installation

    

    

80. Install rear fascia onto vehicle
    참고

    16x tabs, Recommend assistance, Sides will need to be spread apart to clear bumper structure

    

81. Install bolts securing rear center fascia onto body
    참고

    2x bolts, 10mm, 6 Nm

    

82. Install license plate
    참고

    4x screws, Phillips PH2, 1 Nm

    

83. Install bolts securing rear diffuser onto body
    참고

    9x bolts, 10mm, 6 Nm

    

    

    

84. Install rear fascia connector
    참고

    1x connector, Secure locking tab

    

85. Install clips securing LH rear wheel liner onto rear fascia and diffuser
    참고

    5x clips

    

86. Install LH rear aft fender flare carrier
    참고

    2x bolts, 10mm, 7 Nm

    

    

87. Install clips securing LH rear wheel liner to aft fender flare carrier
    참고

    2x clips

    

88. Install LH rear aft fender flare
    참고

    5x clips, Replace any damaged or missing clips

    

    

    

    

89. Install clips securing RH rear wheel liner onto rear fascia and diffuser
    참고

    5x clips

    

90. Install RH 2nd row seat back assembly
    참고

    2x push clips, 4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Connect electrical harness before fully seating assembly, Engage locking tab

    

    

    

    

    

    

    

    

    

91. Install clip securing RH 2nd row seat outboard B cover assembly
    참고

    1x clip, Ensure strap is not twisted

    

    

92. Install RH 2nd row shoulder cover
    참고

    7x clips, 1x datum

    

    

    

93. Install RH Upper C-pillar
    참고

    5x clips, 3x tabs

    

    

    

94. Install rear wall lower trim
    참고

    2x push clips, 4x clips

    

    

    

    

    

95. Secure LH lower C-pillar trim
    참고

    1x clip, 1x datum

    

96. Fold down 2nd row 60 seat
    참고

    Pull tether to release then pivot down until locked in place

    

    

97. Install RH lower C-pillar trim
    참고

    1x clip, 1x datum

    

98. Fold down 2nd row 40 seat
    참고

    Pull tether to release then pivot down until locked in place

    

    

99. Install 2nd row floor mat

    

    

100. Secure RH cantrail panel
     참고

     5x clips, 1x connector, 3x bolts, T30, 6 Nm, Secure tethers then secure clips

     

     

     

     

     

101. Install RH coat hook bolt
     참고

     1x bolt, T20, 2.5 Nm

     

102. Install RH coat hook bolt cover
     참고

     2x tabs

     

     

103. Close RH coat hook
     참고

     Press to secure

     

     

104. Install RH upper A-pillar panel
     참고

     8x clips, 1x tether clip, 1x edge clip, 1x connector, 1x bolt, 10mm, 6 Nm, Ensure tethers are correctly oriented, Replace any missing or damaged clips

     

     

     

     

     

105. Install RH mid A-pillar trim
     참고

     1x clip, 3x tabs, Replace any missing or damaged clips

     

     

     

106. Install RH outer bed side
     참고

     13x bolts, 13mm, 28 Nm, 1x screw, T30, 8 Nm, Assistance required, Have assistant hold panel against body then install bolts hand tight, Adjust gap and flush as required then torque bolts

     

     

     

     

107. Install LH body side tail lamp
     참고

     1x connector, 2x datums, 2x bolts, T30, 5 Nm, Push forwards to engage datums, Engage locking tab

     

     

     

108. Secure RH tail lamp applique
     참고

     2x clips, 2x datums

     

     

109. Install RH bed side wall
     참고

     2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

     

     

     

     

     

     

     

     

     

110. Install RH bed closeout panel
     참고

     6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle

     

     

     

111. Install RH upper bed side wall assembly
     참고

     13x clips, Replace any missing or damaged clips

     

     

112. Install RH sail applique
     참고

     13x clips, Replace any damaged clips

     

     

113. Install bed floor assembly
     참고

     10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

     

     

     

     

     

114. Install fastener covers onto bed floor assembly
     참고

     14x covers

     

     

     

     

115. Install LH rear fore fender flare carrier
     참고

     6x bolts, 10mm, 7 Nm, 1x connector, Connect BLE then install carrier, Engage locking tab

     

     

     

116. Install RH rear aft fender flare carrier
     참고

     2x bolts, 10mm, 7 Nm

     

     

117. Install clips securing LH rear wheel liner to fore fender flare carrier
     참고

     5x clips

     

     

118. Install clips securing RH rear wheel liner to aft fender flare carrier
     참고

     2x clips

     

119. Install RH rear fender flare
     참고

     18x clips, Replace any missing or damaged clips

     

     

     

120. Install RH cantrail assembly
     참고

     7x clips, Recommend assistance, Vehicles may be equipped with 10 or 11 clips in production range

     

     

121. Install screws securing RH cantrail
     참고

     8x screws, T20, 2.5 Nm, Pull C-pillar applique down as required for access

     

     

122. Install RH header seal
     참고

     Start from front quarter glass, Push upwards into seal carrier grooves

     

     

     

     

123. Install RH sail baffle closeout
     참고

     6x clips, Replace any missing or damaged clips

     

     

124. Install LH C pillar applique
     참고

     1x connector, 2x clips, 1x bolt, 10mm, 6 Nm, Slide upwards then push inwards to secure clip,

     

     

     

     

125. Install LH C pillar applique closeout
     참고

     2x clips

     

     

126. Install LH sail baffle applique
     참고

     3x clips, Replace any missing or damaged clips

     

     

127. Install nut securing RH front outer cantrail
     참고

     1x nut, 8mm, 4 Nm, Install new nut

     

     

128. Install RH underhood apron
     참고

     3x clips

     

     

     

129. Connect first responder loop and MV battery connector
     참고

     2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down

     

     

     

130. Install frunk assembly
     참고

     6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Install bolt covers to frunk floor, Install washer fluid cap, Install bumpstops by aligning tabs then turning clockwise, Ensure emergency frunk release functions

     

     

     

     

     

     

     

     

     

131. Install rear underhood apron
     참고

     9x clips, Adjust windshield seal as required

     

     

132. Close powered front trunk
     참고

     Via exterior switch or UI

     

133. ODIN 루틴 실행
134. Close tailgate

     

135. Close all four doors
136. Raise all 4 windows
     참고

     Verify switch is operating as expected