2026-08-09

Coil Spring Assembly - Front - LH (Long Range) (Remove and Replace)

교정 코드 31010600902 0.78 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-05-08: Remove incorrectly added halfshaft and spring compressor steps.
  • 2026-05-06: Added steps to compress coil spring.
  • 2026-02-09: Updated step for Service Mode Plus.
  • 2025-06-21: New procedure released.
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

탈거

  1. 차량을 들어 올려서 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  2. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  3. 전동식 프렁크를 엽니다.
  4. Place the vehicle into Service Mode Plus. See Toolbox 3(연결 및 연결 해제).
  5. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
  6. Remove the frunk assembly. See Frunk Assembly (Remove and Install).
  7. Remove the bolt that attaches the remote brake fluid reservoir to the megabeam, and then remove the reservoir from the megabeam.
    경고
    Avoid tipping the reservoir over.
    참고
    Push under cowl to allow access.
    참고
    10mm, 1x tab
  8. Remove and discard the fasteners (x3) that attach the LH front coil spring assembly to the vehicle.
    참고
    18mm, 110 Nm
  9. Remove the LH front wheel. See 휠 어셈블리(탈거 및 장착).
  10. Disconnect the harness electrical connectors (x2), and then release the clips (x2) and grommet that attach the harness to the coil spring assembly.
    참고
    Pull the grey tab, and then push down to release.
  11. Release the clips (x4) that attach the LH front coil spring assembly cover to the vehicle, and then release the coil spring assembly cover from the assembly.
    참고
    Leave the cover attached to the brake hose.
  12. Remove the bolt that attaches the LH front brake hose bracket to the knuckle, and then remove the bracket from the knuckle.
    참고
    10mm, 10 Nm
  13. Remove and discard the bolt that attaches the outer tie rod to the knuckle, and then remove the tie rod from the knuckle.
    참고
    21mm, 170 Nm
  14. Remove the bolts (x3) that attach the LH front lower control arm shield to the vehicle, and then remove the shield from the vehicle.
    참고
    10mm, 7 Nm
  15. Remove and discard the nut that attach the stabilizer bar to the LH link, and then disconnect the bar from the link.
    참고
    Counter hold the stud as needed.
    참고
    21mm, 275Nm
  16. Position and raise a pole jack onto the LH front lower control arm.
  17. Remove the nut that attaches the LH front upper control arm to the knuckle.
    참고
    Use a step ladder as needed.
    참고
    18mm, 85 Nm
  18. Lower and remove the pole jack from the LH front lower control arm.
  19. Remove the bolts (x2) that attach the front coils spring assembly to the vehicle.
    참고
    Be prepared for some spring load to release from bushings.
    참고
    21mm, 140 Nm
  20. Push down on the knuckle assembly, and then lift the LH front coil spring assembly towards the rear and LH side of the vehicle to remove it from the vehicle.
    경고
    Make sure no harnesses or lines remain attached.

장착

  1. While pulling the knuckle assembly downward, position the LH front coil spring assembly into the mounting hole.
    경고
    Make sure the damper valves are facing the rear of the vehicle.
    참고
    Install via rear area of suspension.
  2. Install new nuts (x3) that attach the LH front coil spring assembly to the vehicle.
    참고
    18mm, 110 Nm
  3. Position the remote brake fluid reservoir to the megabeam, and then install the bolt.
    참고
    Make sure there is no fluid loss. Top off if needed.
    참고
    10mm
  4. Position the LH damper to the lower control arm, and then install install the bolts (x2).
    참고
    21mm, 140 Nm
  5. Position and raise pole jack onto the LH front lower control arm.
  6. Position the LH front upper control arm to the knuckle, and then install a new nut that attaches the control arm to the knuckle.
    참고
    Use a step stool as needed.
    참고
    18mm, 85 Nm
  7. Lower and remove the pole jack from the LH front lower control arm.
  8. Position the stabilizer bar to the link, and then install a new bolt that attaches stabilizer bar to the link.
    참고
    Counter hold the stud as required.
    참고
    21mm, 275Nm
  9. Position the outer tie rod to the knuckle, and then install a new nut that attaches the tie rod to the knuckle.
    참고
    21mm, 170 Nm
  10. Position the LH front brake hose bracket onto the knuckle assembly, and then install the bolt that attaches the bracket to the assembly.
    참고
    10mm, 10 Nm
  11. Position the LH front coil spring assembly cover to the vehicle, and then secure the clips (x4) that attach the cover to the vehicle.
  12. Connect the electrical connectors (x2), and then secure clips (x2) and grommet that attach the harness to the front coil spring assembly module.
  13. Position the LH front wheel onto the vehicle, and then install and hand tighten the lug nuts (x6).
    참고
    21mm, 205 Nm
  14. Lower vehicle until tires are touching the ground.
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  15. Install the frunk assembly. See Frunk Assembly (Remove and Install).
  16. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Install).
  17. Install the LH front wheel. See 휠 어셈블리(탈거 및 장착).
  18. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  19. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.