2025-10-08

Gearbox Fluid - Rear Drive Unit (Dual Motor) (Top Off)

교정 코드 40300135 FRT 0.54 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-02-04: Added steps for Service Mode and rearranged steps for better flow.
  • 2025-01-14: Noted that additional diagnosis may be necessary if over 300 mL of fluid was added.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  1. 차량을 들어 올려서 지지합니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  2. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  3. 차량을 정비 모드로 전환합니다. 참조 항목: 정비 모드.
  4. Remove the mid aeroshield. See Skid Plate - Rear (Remove and Install).
  5. Position an oil drain container underneath the rear drive unit.
  6. Remove oil fill plug from RDU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x plug, 8mm Allen, 15 Nm, Verify the O-ring is not damaged, Replace O-ring as needed
  7. Release the clips (x3) that attach the RH side of the acoustic cover to the lower portion of the acoustic cover.
  8. Release the clips (x2) that attach the RH side of the acoustic cover to the drive unit assembly.
  9. Set up fill kit with KAF1
    Informational PurposesAn informational icon, calling your attention
    참고
    Add extra oil to container as it will prevent underfill and additional air being injected. Only use KAF1 fluid, Do not interchange or mix oil types
  10. Position oil pump hose into fill hole
  11. Pump fluid into rear drive unit
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    구동 장치에 500mL 이상의 기어박스 오일을 보충한 경우 추가 진단이 필요할 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pump fluid into drive unit until fluid spills out. Use excess gearbox fluid in fill container to allow oil pump to dispense fluid without drawing air
  12. Remove oil pump hose from fill port
    Informational PurposesAn informational icon, calling your attention
    참고
    Turn knob to off and remove from fill hole
  13. Secure oil fill plug onto RDU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x plug, 8mm Allen, 15 Nm, Verify the O-ring is not damaged, Replace O-ring as needed
  14. Spray area with brake cleaner and wipe any residual fluid
  15. Secure the clips (x2) that attach the RH side of the acoustic cover to the drive unit.
    Informational PurposesAn informational icon, calling your attention
    참고
    Route the cover between subframe and axle.
  16. Remove the oil drain container from underneath the vehicle.
  17. Install the mid aero shield. See Skid Plate - Rear (Remove and Install).
  18. Lower the vehicle fully.
  19. 정비 모드를 종료합니다. 참조 항목: 정비 모드.
  20. 리프트에서 차량을 내립니다. 참조 항목: 차량 상승 - 2 포스트 리프트.
  21. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.