2026-10-01

控制器 - 高压(七座) ((拆卸和更换))

校正代码 16301652 FRT 1.44 注意:除非本程序中另有明确规定,否则上文所列校正代码及相关 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时深入了解 FRT 及其创建方式。 注意:请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意:请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-09-09: Released new procedure.
警告
本程序为“草案”。虽已通过验证,但可能仍有“警告”和“注意”事项缺失。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。
警告
When servicing the ancillary bay cover and components in or around the ancillary bay, there is a possibilty of encountering metal flashing on the inner edge of the vehicle single-piece rear casting. These sharp protrusions are a cut hazard, and proper PPE should be worn if there is a chance of contacting the flashing unprotected. If not already wearing leather over gloves, then at least wear cut-resistant gloves when the flashing is present.
警告

只有完成全部所需认证的技术人员才能执行此程序。Tesla 特斯拉建议第三方服务提供商技术人员在执行此程序之前接受同等培训。有关 Tesla 技术人员要求的更多信息,或第三方主题说明,请参阅高压认证要求。处理高压线缆、母排或接头时,务必全程穿戴最低防护等级为 0(1000V) 的适当个人防护装备 (PPE)及高压绝缘手套。有关其他安全信息,请参阅技术注意事项 TN-15-92-003,高压安全意识注意事项。

拆卸

  1. Open all four doors and lower all four windows.
  2. Remove the LH and RH lower C-pillar trim. See 饰板 - C 柱 - 下 - 左侧(七座)(拆卸和更换).
  3. Remove the 2nd row seats. See 座椅总成 - 第二排 - LH(七座)(拆卸和更换) and 座椅总成 - 第二排 - 右侧(七座)(拆卸和更换).
  4. Remove the 3rd row seat cushion and the LH and RH seat cushion bolsters. See 承梁 - 座垫 - 第三排 - 左侧(拆卸和更换).
  5. Remove the 3rd row carpet. See 地毯 - 第三排(拆卸和更换).
  6. Disconnect the LV power. See 12V/低压电源(断开和连接).
  7. Remove the 3rd row NVH insulator. See NVH 隔音板 - 第三排座椅(拆卸和更换).
  8. Remove all items from pockets and ensure not wearing metal items.
  9. Inspect HV insulating gloves.
    注
    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
  10. Put on HV insulating gloves, leather outer gloves, and safety glasses.
    警告
    Continue to wear the gloves until instructed to remove them.
  11. Remove the ancillary bay probe cover. See 盖 - 高压探针 - 高压电池(拆卸和更换).
  12. Use a multimeter to probe the voltages.
    警告
    为减少可能接触高压的风险,请按照如下顺序测量高压:
    Measurement Order

    Component Test

    B+

    (Probe opening closer to HV DC connector)

    B-

    (Probe opening, closer to HV Processor Logic connector)

    GND

    Measured Voltage less than 10 V

    Measured Voltage 10 V or more

    1

    HV battery positive contactor

    Positive (+) Lead

    Negative (-) Lead on ancillary bay cover

    Pass

    Fail

    HV battery positive contactor might be seized. See高压电池触点开关检查.

    2

    HV battery negative contactor

    Positive (+) Lead

    Negative (-) Lead on ancillary bay cover

    Pass

    Fail

    HV battery negative contactor might be seized. See高压电池触点开关检查.

    3

    HV

    Positive (+) Lead

    Negative (-) Lead

    Pass

    Fail

    Perform a HV battery contactor seize check. See高压电池触点开关检查.

    提示
    推荐使用以下工具
    • Electrical Protective Gloves
    • Slim Test Probes - 1130480-02-B
    • Fluke 1587 - 1076921-00-A
    图 1. B+ to Ground measurement
    图 2. B- to Ground measurement
    图 3. B+ to B- measurement
  13. Install the ancillary bay probe cover. See 盖 - 高压探针 - 高压电池(拆卸和更换).
  14. Remove the ancillary bay cover. See 盖板 - 高压电池仓(七座)(拆卸和更换).
  15. Inspect the ancillary bay for any missing insulators and install service insulator kit before continuing to next step.
    注
    The number of bolts on newer vehicles may vary.
  16. Remove the pyrotechnic battery disconnect. See 烟火电池断接开关(拆卸和更换).
  17. Disconnect the high voltage controller connectors (x7).
  18. Remove the bolts (x2) that attach the high voltage controller to the high voltage controller tray, and then remove the high voltage controller from the vehicle.
    注
    Use of the following tool(s) is recommended:
    • Insulated Ratchet/torque wrench
    • Insulated 4 in extension
    • External Torx E6
    • Electrical Protective Gloves

安装

  1. Position the high voltage controller on the high voltage controller tray, and then install the bolts that attach the controller to the tray.
    2 Nm (1.5 lbs-ft)
    注
    Use of the following tool(s) is recommended:
    • Insulated Ratchet/torque wrench
    • Insulated 4 in extension
    • External Torx E6
    • Electrical Protective Gloves
  2. Connect the high voltage controller connectors (x7).
  3. Install the pyrotechnic battery disconnect. See 烟火电池断接开关(拆卸和更换).
  4. Install the ancillary bay cover. See 盖板 - 高压电池仓(七座)(拆卸和更换).
  5. Install the 3rd row NVH insulator. See NVH 隔音板 - 第三排座椅(拆卸和更换).
  6. Connect the LV power. See 12V/低压电源(断开和连接).
  7. Install the 3rd row carpet. See 地毯 - 第三排(拆卸和更换).
  8. Install the 3rd row seat cushion and the LH and RH seat cushion bolsters. See 承梁 - 座垫 - 第三排 - 左侧(拆卸和更换).
  9. Install the 2nd row seats. See 座椅总成 - 第二排 - LH(七座)(拆卸和更换) and 座椅总成 - 第二排 - 右侧(七座)(拆卸和更换).
  10. Install the LH and RH lower C-pillar trim. See 饰板 - C 柱 - 下 - 左侧(七座)(拆卸和更换).
  11. Raise the LH front window and close the LH front door.