2026-07-02
执行常规检查 (Inspection)
校正代码
00030700
FRT
0.90
注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时深入了解 FRT 及其创建方式。
注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅人体工程学注意事项查看安全健康的作业规程。
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
- 2026-06-18: Released new procedure.
拆卸
-
Open all doors from the exterior. Verify that the door operates normally and does not do any of the following:
- Collide with the body or brightwork
- Produce unusual noises such as creaks, groans, or clicks
- Pause or fail to fully open
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions -
Function check all windows from the LH front switch. Document any abnormal operation or noises.
-
Function check exterior lights. Verify that the following lights operate normally:
- Headlights (LH and RH)
- Fog lights (LH and RH)
- Taillights (LH and RH)
- Center high mount stopping light (third brake light)
- Reverse lights (LH and RH)
- Side repeaters (LH and RH)
- Front turn signals (LH and RH)
- Rear turn signals (LH and RH)
-
Close the door and hood, then function check the windshield wipers and spray jets. Verify the following:
- The wipers and jets function
- The wipers move in a full range of motion
- The wipers move at all speeds
- The wipers do not interfere with other components
- The wipers do not produce abnormal noises such as creaks, groans, and clicks
- The wipers do not pause
-
Honk the horn. Verify that both high- and low-tone horns produce sound.
-
Open the hood.
-
Remove the rear apron
注14x clips
-
Visually inspect the brake fluid level.
-
Visually inspect the coolant level. Ensure that the fluid level is at the Max line. Top off as necessary.
- Raise the vehicle. See 举升车辆 - 四柱举升机.
-
Remove the outer fasteners from the front aero shield.
-
Remove the remaining nuts (x2), and then remove the front aero shield from the vehicle.
-
Remove LH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Remove RH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Remove rear aero shield
注11x bolts, 10mm, 5 Nm, Fasteners may vary, MYSP will have one less bolt
-
Check all four tire pressures manually
注4x tires, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures
-
Record tread depth for LH rear tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Perform visual inspection of LH rear brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec: See technical data
-
Record tread depth for RH rear tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Perform visual inspection of RH rear brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect RH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec : See technical data
-
Record tread depth for RH front tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Perform visual inspection of RH front brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect RH front brake rotor condition
注Check for excessive rust or wear, Minimum spec: See technical data
-
Record tread depth for LH front tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Perform visual inspection of LH front brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH front brake rotor condition
注Check for excessive rust or wear, Minimum spec: See technical data
-
Perform visual inspection of all brake pipes and hoses
注Pay special attention to brake junction points
-
Perform inspection of vehicle underside components front and rear
注Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
-
Inspect underside of vehicle for fluid leaks
-
Perform inspection of steering components
注Check steering gear joints and electrical connections, Verify components are not bent or damaged
-
Perform visual inspection of HV battery enclosure
注Check for any dents, scrapes, or other damage
-
Perform inspection of front suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Perform inspection of rear suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Install rear aero shield
注11x bolts, 10mm, 5 Nm, Fasteners may vary, Model Y Structural Pack has one less bolt and one extra clip, Apply Loctite 222 onto rear aero shield bolts before installing
-
Install RH rear suspension cover
注2x tabs, 1x bolt, 10mm, 5 Nm, Apply Loctite 222 onto rear suspension cover bolt
-
Install LH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Position the front aero shield on the vehicle, and then install the nuts that attach the aero shield to the vehicle.
-
Apply Loctite 222 on the front aero shield bolts, and then install the bolts on the aero shield.
-
Lower vehicle fully
注Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Remove vehicle from lift
注Lower rack arms fully and remove from under vehicle
-
Fill washer reservoir with fluid
-
Install rear apron
注14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
-
Close hood
-
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance
注The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
-
Inspect vehicles alignment
注Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction