17/06/2024 21:23:35
前轮罩 NVH 降噪衬垫 - LH(拆卸和更换)
校正代码 15306090 0.50 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com。注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
- 2023-10-10: Added a caution to not manually close the charge port door.
警告
本程序为“草案”。虽已通过验证,但可能仍有“警告”和“小心”事项缺失。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com。
- Open all four doors
- Lower all four windows
- Move LH front seat forward
-
Tilt 7s 2nd row 60 seat forward
注Hold 2nd row 60 seat LH shoulder switch, Slide seat all the way forward and tit up
-
Partially remove LH rear door seal
-
Remove LH 7s Lower C-Pillar Trim
注8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Move RH front seat forward
-
Position 40 seat into easy entry mode
注Press shoulder switch and push 40 seat forward to position into easy entry mode
-
Remove 3rd row seat cushion and disconnect harness
注1x connector, Pull LH and RH release lever under 3rd row seat cushion to release seat cushion
-
Remove 3rd row LH seat cushion bolster
注1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster towards front of vehicle to remove
-
Open liftgate
-
Remove rear load floor
-
Remove trunk sill trim
注4x clips
-
Remove 7s LH load floor bracket
注2x clips
-
Remove LH trunk pocket bracket
注1x push clip, 5x alignment tabs
-
Release 3rd row LH seat backrest
注Front switch at LH trunk trim panel
-
Open charge port door
-
Open the hood.
-
Power off the vehicle using the touchscreen.
-
Remove the rear apron.
-
Disconnect the 12V negative battery cable and First Responder Loop.
- Empty all pockets and remove all metal objects such as watches and jewelery.
-
Inspect the HV insulating gloves for any damage.
-
Put on the HV insulating gloves and leather over gloves.
-
Verify there is no high voltage present at the charge port
注Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage components, Measure B+ to B-, B- to Ground, and B+ to Ground (use rear left door striker as a ground for the test), If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering
-
Remove HV insulating gloves
-
Release top edge of LH 7s trunk side trim and disconnect 12V outlet and trunk switch connectors
注6x clips, 2x connectors
-
Release remaining clips and remove LH 7s trunk side trim
注1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar, Pull the top of the trunk side trim all the way down flat so it clears the edge of the folded down LH 3rd row seatback and pull straight out
-
Remove LH upper C-pillar trim
注6x clips, Guide front upper corner groove out from headliner and place trim aside
-
Remove LH C-pillar bracket
注3x clips, 1x manual release cable, 1x harness clip
-
Release connectors from charge port assembly
注2x connectors, Remove white locking tab, Depress tab to release connection from the charge port, Continue to pull off connector, The charge port connection is intended to disengage safety cap when released, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
-
Remove charge port safety cap
注2x tabs
-
Remove fasteners securing charge port busbar to charge port and remove busbar leads from studs
注2x nuts, 10mm, 9 Nm, Nuts have captured washers
-
Release harness guide from body at LH rear door sill
注3x clips
-
Remove bolt securing lower LH 2nd row retractor anchor to body
注1x patch bolt, 15mm, 35 Nm, Discard after removal
-
Release LH front wheelhouse NVH insulator from wheelhouse
注Maneuver busbar to assist with clearing space for the wheelhouse to remove
-
Secure LH front wheelhouse NVH insulator onto wheelhouse
注Maneuver the busbar to successfully tuck insulator onto wheelhouse
-
Install bolt securing lower LH 2nd row retractor anchor to body
注1x patch bolt, 15mm, 35 Nm, Install new patch bolt
-
Secure harness guide to body at LH rear door sill
注3x clips
-
Clean charge port assembly busbar contact surface of residual penetrox
注Use plastic trim tool to push IPA wipe down between plastic divider, Allow 1 minute dry time
-
Verify charge port studs are torqued to specification
注2x studs, T10, 2 Nm
-
Apply Penetrox to backside of busbar leads
注Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered
-
Install charge port busbar leads to charge port assembly
注2x nuts, 10mm, 9 Nm, Nuts have captured washers, If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary
-
Inspect HV insulating gloves
注Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf
-
Put on HV insulating gloves and leather over gloves
注Make sure to wear Electrical Protective Gloves any time Hioki tester is used
-
Perform Hioki resistance test at each HV joint from HV busbar lead to charge port stud
注2x HV joints, The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.270 mΩ (270 μΩ).If the resistance is greater than 0.270 mΩ (270 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step.
- Remove HV insulating gloves
-
Install charge port safety cap
注2x tabs
-
Secure connectors onto charge port assembly
注2x connectors, Install white locking tab, Engage red locking tab
-
Install LH C-pillar bracket
注3x clips, 1x manual release cable, 1x harness clip
-
Install LH upper C-pillar trim
注6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim
-
Position LH 7s trunk side trim and install lower clips
注1x push clips, 5x clips, Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly, Guide front clip stanchions around LH C-pillar
-
Connect 12V outlet and trunk switch connectors then install top edge of LH 7s trunk side trim
注6x clips, 2x connectors
-
Install LH trunk pocket bracket
注1x push clip, 5x alignment tabs
-
Install 7s LH load floor bracket
注2x clips
-
Install trunk sill trim
注4x clips, Seat seal around edge of trim
-
Install rear load floor
-
Connect the First Responder Loop and 12V negative battery cable.
-
Close charge port door.
警告请勿尝试手动关闭充电端口盖板。
-
Raise 3rd row LH seat backrest to its original position
注Manually raise backrest up to its original position until it locks into place
-
Close liftgate
-
Install LH 7s Lower C-Pillar Trim
注8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Reseat LH rear door seal
注Seat pillar and sill trim tabs underneath seal
-
Install 3rd row LH seat cushion bolster
注1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster into seat frame assembly
-
Install 3rd row seat cushion and connect harness
注1x connector, Secure 3rd row seat cushion into RH and LH latches
-
Move 40 seat to original position
- Move the RH front seat to its original position.
-
Position 7s 2nd row 60 seat back to its original position
注Tilt 2nd row 60 seat down, Press LH shoulder switch and slide back into original position
-
Move LH front seat to original position
注This can also be achieved by selecting driver profile via UI
- Raise all four windows
-
Close all four doors
注If 12V is powered up, Unlatch rear doors before closing