30/08/2022 20:29:24

制动管路 - 主缸至防抱死制动系统（非结构化电池组）（右侧驾驶）（拆卸和更换）

校正代码 33034202 2.04 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

拆卸

  1. Open the RH front door and lower the RH front window.
  2. Remove the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  3. Remove the underhood storage unit. See 前备箱储物单元（拆卸和更换）.
  4. Disconnect 12V power. See 12V/低压电源（断开和连接）.
  5. Remove the 12V battery. See 12V/低压电池（拆卸和更换）.
  6. Remove the fresh air intake duct. See 风管 - 高效分子空气 (HEPA)（拆卸和更换）.
  7. Remove the front aero shield. See 面板 - 流线型护板 - 前（非结构化电池组） （拆卸和更换）.
  8. Remove the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
  9. Remove the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
  10. Remove the LH and RH bolts that attach the shock tower brace to the body.
    55 Nm (40.6 lbs-ft)
    55 Nm (40.6 lbs-ft)
  11. Remove the LH and RH outer bolts that attach the shock tower brace to the body.
    62 Nm (45.7 lbs-ft)
  12. Disconnect the HVIL connector.
  13. Remove the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
    31 Nm (22.9 lbs-ft)
  14. Carefully remove the AC compressor and AC compressor bracket towards the front of the vehicle, under the shock tower brace.
  15. Disconnect the electrical connector from the ABS unit.
  16. Position the oil drain under the ABS unit.
  17. Loosen the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  18. Loosen the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  19. Place an absorbent material beneath the brake booster and reservoir area.
  20. Using a brake fluid syringe, remove the brake fluid from the reservoir.
  21. Loosen the nut that attaches the secondary brake line to the master cylinder, and then remove the secondary brake line.
    16 Nm (11.8 lbs-ft)
  22. Loosen the nut that attaches the primary brake line to the master cylinder, and then remove the primary brake line.
    16 Nm (11.8 lbs-ft)
  23. Release the primary and secondary brake lines from the brake line bundle clip.
  24. Remove the bolts (x2) that attach the ABS unit to the frame rail.
    10 Nm (7.4 lbs-ft)
  25. Move the ABS unit and bracket towards the 12V battery area to make sure there is space to remove the brake lines.
  26. Remove the brake lines from the bundle clips (x2) under the ABS unit.
  27. Remove and discard the bolts (x2) that attach the harness guide to the front controller, and then release the harness guide.
    6 Nm (4.4 lbs-ft)
  28. Remove brake line bundle clips (x3).
  29. Route the master cylinder brake lines towards the right controller, and then remove the master cylinder brake line bundle from the vehicle.

安装

  1. Route the master cylinder brake lines from the controller towards the ABS unit, and then put the brake lines into position.
  2. Install the brake line bundle clips (x3).
  3. Mount the brake lines to the bundle clips (x2)under the ABS unit.
  4. Fasten the bolts (x2) that attach the harness guide to the front controller.
    Informational PurposesAn informational icon, calling your attention
    注
    Replace the patchbolts.
    6 Nm (4.4 lbs-ft)
  5. Mount the primary and secondary brake lines to the brake line bundle clip.
  6. Fasten the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  7. Fasten the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  8. Clean the ABS unit surface of residual brake fluid.
  9. Put the ABS unit and bracket into position.
  10. Remove the oil drain container from underneath vehicle
  11. Install the bolts (x2) that attach the ABS unit to the frame rail.
    10 Nm (7.4 lbs-ft)
  12. Install the secondary brake line to the master cylinder, and then fasten the nut that attaches the secondary brake line.
    16 Nm (11.8 lbs-ft)
  13. Install the primary brake line to the master cylinder, and then fasten the nut that attaches the primary brake line.
    16 Nm (11.8 lbs-ft)
  14. Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
  15. Carefully position the AC compressor and AC compressor bracket into the vehicle.
  16. Fasten the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
    31 Nm (22.9 lbs-ft)
  17. Install the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
  18. Install the LH and RH bolts that attach the shock tower brace to the body.
    55 Nm (40.6 lbs-ft)
    55 Nm (40.6 lbs-ft)
  19. Install the LH and RH outer bolts that attach the shock tower brace to the body.
    62 Nm (45.7 lbs-ft)
  20. Install the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
  21. Connect the HVIL connector
  22. Install the 12V battery. See 12V/低压电池（拆卸和更换）.
  23. Reconnect 12V power. See 12V/低压电源（断开和连接）.
  24. Install the fresh air intake duct. See 风管 - 高效分子空气 (HEPA)（拆卸和更换）.
  25. Install the underhood storage unit. See 前备箱储物单元（拆卸和更换）.
  26. Bleed the brakes. See 制动液排放/冲洗
  27. Install the front aero shield. See 面板 - 流线型护板 - 前（非结构化电池组） （拆卸和更换）.
  28. Install the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  29. Perform a test drive.
    Informational PurposesAn informational icon, calling your attention
    注
    Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing