04/06/2024 21:10:10
摄像头 - 双头 - 前置（拆卸和更换）
校正代码
17221002 0.36 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。
注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
拆卸
- Open the LH front door and lower the LH front window.
- Remove the lower quad camera cover. See 四摄像头盖 - 下（拆卸和更换）.
- Remove the rear view mirror. See 镜 - 后视（拆卸和更换）.
-
Release the clips that attach the
upper quad camera cover to the windshield bracket, and then separate the cover from the
bracket.
警告Carefully release the cover from the windshield bracket, as an electrical harness is still attached.
-
Release the connector lock, and then
disconnect the rearview mirror upper cover assembly.
注Connector count may vary depending on the vehicle configuration.
-
Release the locking tab, and then
disconnect the GNSS antenna connector.
-
Release the tabs that attach the glare
shield to the windshield bracket, and then remove the glare shield from the windshield
bracket.
-
Remove and discard the screws (x4)
that attach the forward facing bi camera to the vehicle, and then remove the camera
assembly from the vehicle.
1 Nm (.7 lbs-ft)提示： Use of the following tool(s) is recommended:- T10 bit
-
Release the locking tabs, and then
disconnect the forward facing camera assembly connectors (x2).
安装
-
Clean the inner windshield camera
viewing area with a clean microfiber cloth and glass cleaner. Let the windshield fully
dry before continuing.
警告Verify that the windshield has no stains or leftover residue. Otherwise, Autopilot features may be hindered.
-
Position the forward facing camera
into the vehicle, connect the connectors (x2), and then secure the connector
locks.
-
Install new screws (x4) that attach
the forward facing bi camera to the vehicle.1 Nm (.7 lbs-ft)提示： Use of the following tool(s) is recommended:
- T10 bit
-
Position the glare shield to the
windshield bracket, and then secure the tabs (x2) that attach the glare shield to the
windshield bracket.
-
Connect the GNSS antenna connector,
and then secure the connector lock.
-
Connect the rear view mirror upper
cover assembly, and then secure the connector locks.
注Connector count may vary depending on the vehicle configuration.
-
Connect the interior camera connector,
and then install the clips that attach the upper quad camera cover to the vehicle.
- Connect a laptop with Toolbox 3 to the vehicle.
- Unlock the vehicle gateway. See 网关（解锁）.
-
On the vehicle touchscreen, tap Driver
Assist > Cameras > Reset DAS.
注Make sure all cameras and reset DAS icon turn green.
- Click the Actions/Autodiag, and then search for "Calibration Mode".
- Click DAS Enter Calibration Mode, click Run, and allow the routine to complete.
- Click Actions, and then search for "Front Camera".
-
Click PING-HTTP_DAS_X_MAIN-CAMERA-SCRIPTSearch for routine in Toolbox, change the timeout to "100", and then click
Run.
注The routine will need to be performed within a 5 minute calibration window.注Choose the routine that has the "SCRIPT" at the end of the path name.
- Click the Actions, and then search for "Fisheye Camera".
-
Click PING-HTTP_DAS_X_FISHEYE-CAMERA-SCRIPTSearch for routine in Toolbox, and then click Run.
注Routine will need to be performed within 5 minute calibration window.注Choose the routine that has the "SCRIPT" at the end of the path name.
- Adjust the forward facing camera. See 摄像头 - 前置（倾角验证）.