校正代码 16307302 2.40 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

1. Open all the doors and lower all the windows.
2. Place vehicle in service mode with touchscreen
   注

   Hold Tesla T icon at top of center display for four seconds and then type "service" into dialog box
3. Remove the ancillary bay cover. See 盖板 - 高压电池仓（结构化电池组）（拆卸和更换）.
4. 拆下烟火电池隔离开关。请参阅烟火电池断接开关（结构化电池组）（拆卸和安装）。
5. Disconnect HV controller connectors
   注

   7x connectors, Lift hinge upwards to release levered connection

   

   

6. Release harness clips from HVC hinge tray and route harness away
   注

   3x clips

   

7. Remove bolts securing HV controller hinge tray to HV battery
   注

   2x bolts, 8mm, 2 Nm

   

   

8. Remove HV controller and tray from ancillary bay

   

9. Remove 63A fuse cover
   注

   2x securing tabs

   

10. Disconnect HVIL connector from HV heatpump harness
    注

    1x connector

    

11. Remove 63A fuse from ancillary bay
    注

    2x nuts, 8mm, 2.5 Nm, Discard after removal

    

12. Remove inner 63A fuse from ancillary bay
    注

    2x nuts, 8mm, 2.5 Nm, Discard after removal

    

13. Remove ancillary bay harness from plastic bobbin stud

    

14. Remove bolts securing PCS to HV battery
    注

    6x bolts, 8mm, 6 Nm, Ensure ONLY the 8mm fasteners are removed, Do not remove the T30 fasteners

    

15. Remove ancillary bay harness from negative DC link
    注

    1x nut, 8mm, 1.5 Nm, Discard nut after removal

    

16. Release ancillary bay harness from tray between PCS and bobbin
    注

    1x clip

    

17. Remove nut securing auxiliary fuse jumper busbar
    注

    1x nut, 8mm, 2.5 Nm, Discard after removal, Slightly shift PCS to gain access to nut, Discard nut after removal

    

    

18. Remove auxiliary fuse jumper busbar

    

    

19. Install auxiliary fuse jumper busbar

    

    

20. Install nut securing auxiliary fuse jumper busbar
    注

    1x nut, 8mm, 2.5 Nm, Install new nut, Shift PCS back into original position

    

21. Install bolts securing PCS to HV battery
    注

    6x bolts, 8mm, 6 Nm

    

22. Secure ancillary bay harness onto tray between PCS and bobbin
    注

    1x clip

    

23. Install ancillary bay harness to negative DC link
    注

    1x nut, 8mm, 1.5 Nm, Install new nut

    

24. Install ancillary bay harness from plastic bobbin stud

    

25. Install inner 63A fuse into ancillary bay
    注

    2x nuts, 8mm, 2.5 Nm, Install new nuts

    

    

26. Install 63A fuse into ancillary bay
    注

    2x nuts, 8mm, 2.5 Nm, Install new nuts

    

    

27. Place holder- Perform Hioki measurement at the joint from 63A fuse to terminal
    注

    1x HV joint, 105µΩ or less, Perform zero adjust to Hioki meter prior to testing

    

28. Place holder- Perform Hioki measurement at the joint of 63A fuse to auxiliary jumper busbar
    注

    1x HV joint, 105µΩ or less, Perform zero adjust to Hioki meter prior to testing

    

29. Place holder- Perform Hioki measurement at the joint of inner 63A fuse to flag nut
    注

    1x HV joint, 105µΩ or less, Perform zero adjust to Hioki meter prior to testing

    

30. Place holder- Perform Hioki measurement at the joint of inner 63A fuse to auxiliary jumper busbar
    注

    1x HV joint, 105µΩ or less, Perform zero adjust to Hioki meter prior to testing

    

31. Connect HVIL connector onto tray
    注

    1x connector

    

32. Install 63A fuse cover
    注

    2x securing tabs

    

33. Position HV controller and tray into ancillary bay

    

34. Install bolts securing HV controller hinge tray to HV battery
    注

    2x bolts, 8mm, 2 Nm

    

    

35. 测量烟火电池隔离开关安装点间的电压，然后安装烟火电池隔离开关。请参阅烟火电池断接开关（结构化电池组）（拆卸和安装）。
36. Install the ancillary bay cover. See 盖板 - 高压电池仓（结构化电池组）（拆卸和更换）.
37. Exit Service Mode through UI
    注

    Controls > Service Mode > Exit Service Mode
38. Raise all the windows
39. Close all the doors
    注

    If 12V is powered up, Unlatch rear doors before closing