校正代码 13084212 0.66 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

1. Open RH front and rear doors
2. Lower all four windows
3. Move LH front seat forward
4. Move RH front seat forward
5. Partially remove LH rear door seal

   

6. Remove LH 7s Lower C-Pillar Trim
   注

   8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim

   

   

7. Fold 60 seat into down position

   

   

8. Disconnect logic connector at LH seat frame
   注

   1x connector

   

9. Move 60 seat forward using towel bar
   注

   With one hand on towel bar pull up and slide the seat forward with your other hand

   

   

10. Remove 60 seat rear outboard track fastener
    注

    1x patch bolt, 11mm, 37 Nm, Discard after removal

    

11. Remove 60 seat rear inboard track fasteners
    注

    2x patch bolts, 11mm, 37 Nm, Discard after removal

    

12. Move 60 seat fully rearward using towel bar
    注

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

13. Remove 60 seat outboard track cover
    注

    1x clip, Slide covers forward to release from 60 seat tracks

    

    

    

14. Remove center track cover from 2nd row seats
    注

    2x clips, Slide covers forward to release from 2nd row seat tracks

    

    

    

15. Release cabin carpet from 60 seat
    注

    Pull cabin carpet towards front of vehicle

    

    

16. Remove 60 seat front inboard track fasteners
    注

    1x bolts, 11mm, 37 Nm, Discard after removal

    

17. Remove 60 seat front outboard track fasteners
    注

    1x bolts, 11mm, 37 Nm, Discard after removal

    

18. Remove 2nd row 60 seat assembly from vehicle
    注

    Recommend assistance

    

    

19. Remove front push clip from 60 outer sideshield assembly
    注

    1x clip, Use pick to remove the push clip from the bottom side of the outboard cover

    

    

20. Remove 60 outer sideshield assembly
    注

    1x clip 1x connector, Remove outer sideshield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection

    

    

21. Remove 60 seat toe kick cover
    注

    7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove

    

    

22. Release clips and remove inboard outer trim from 60 seat
    注

    3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle

    

    

23. Remove 60 seatback panel
    注

    9x clips, 2x hooks, Release clips starting at the top of backpanel working your way down the lower backpanel, pull 60 backpanel towards front of vehicle to remove

    

    

24. Remove 2nd row center seat switch
    注

    1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 backpanel to ease removal

    

    

    

25. Remove center backpanel from center seatback
    注

    5x clips, 2 hooks, Lift up at the lower 20 backpanel and then slide forward to release

    

    

    

26. Release 60 seat harness connectors and clip from seat from seat frame
    注

    1x clip, 7x connectors

    

    

27. Disconnect seat cables from easy entry actuators on 60 seat
    注

    4x clips

    

28. Remove push clips for 60 bottom seat pan
    注

    2x clips, Remove push clips from front of seat pan

    

29. Remove center seatback lumbar bun fastener
    注

    1x screw, T20, 1.5 Nm

    

    

30. Remove center seatback lumbar bun
    注

    2x clips, Pull bolster outwards to release

    

31. Remove center seatback pivot clamps
    注

    2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove

    

    

    

    

32. Remove center seatback from 60 seat frame
    注

    Remove center seatback by lifting upwards

    

33. Manually release the center seatback latch
    注

    Use small screwdriver to manipulate the center seatback latch to release

    

    

34. Remove fasteners securing 60 seat pan to seat frame
    注

    4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame

    

    

    

35. Remove headrest from 60 seat assembly
    注

    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged

    

    

36. Remove headrest guides from 60 seat
    注

    Pull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides

    

    

37. Remove 60 seatback
    注

    4x clips, Release clips securing 60 seatback and lift upwards

    

38. Remove 60 seat bottom
    注

    Remove seat bottom by lifting the rear first and removing it towards front of the seat

    

39. Remove push clip from trim
    注

    1x clip, Remove trim clip from cover

    

40. Remove center inner cover
    注

    2x clips, Pry center inner cover back to disengage clips, Remove by lifting up while pulling back

    

    

41. Remove 60 B-Cover I/B Inner

    

42. Install 60 B-Cover I/B Inner trim

    

43. Install center inner cover
    注

    2x clips, Install inner cover ensuring the clips seat to outer cover

    

44. Install push clip to trim
    注

    1x clip

    

45. Place 60 seat pan onto seat frame
    注

    Reinstall seat bottom onto seat frame by starting at the rear of the seat

    

46. Secure 60 seat bottom to seat frame
    注

    4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame

    

    

    

47. Install headrest guides into 60 seat assembly
    注

    Install headrest guides by pressing downwards until lower tab is seated

    

48. Install 60 seat back into place
    注

    4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back

    

49. Install headrest onto 60 seat assembly
    注

    Push down to secure

    

50. Install center seatback pivot clamps
    注

    2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs

    

    

    

51. Install center seatback lumbar bun fastener
    注

    1x screw, T20, 1.5 Nm

    

    

52. Plug in connector and install trim to 60 seat
    注

    1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.

    

    

53. Install push clip at front of outer 60 sideshield assembly
    注

    1x clip, Install push clip at front bottom side of the trim

    

    

54. Install inboard outer trim to 60 seat
    注

    Clips 3x, Install inboard outer trim and reseat 3x clips

    

55. Insert backpanel hooks into center seat back assembly
    注

    2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks

    

    

56. Install center backpanel onto seat back
    注

    5x clips

    

57. Install 2nd row center seat switch
    注

    1x connector, 2x clips

    

    

    

58. Install 60 toe kick cover
    注

    7x clips

    

    

59. Install LH seatback onto 60 seat assembly
    注

    9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips

    

    

    

60. Connect logic connector at LH 60 seat frame
    注

    1x connector

    

61. Install fasteners securing 60 seat frame to body
    注

    5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front

    

    

    

    

62. Secure cabin carpet to 60 seat
    注

    Strap velcro on

    

    

63. Fold the 60 seat into vertical position
    注

    Remove seat back protection if necessary

    

64. Install 60 seat outboard track cover
    注

    1x clip

    

    

    

65. Install 60 seat outboard track cover
    注

    1x clip

    

    

    

66. Install LH 7s Lower C-Pillar Trim
    注

    8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim

    

    

67. Reseat LH rear door seal
    注

    Seat pillar and sill trim tabs underneath seal

    

68. Move RH front seat to original position
69. Raise all four windows
70. Close all four doors
    注

    If 12V is powered up, Unlatch rear doors before closing