2026-11-02

车门总成 - 充电接口（中国）（拆卸和更换）

校正代码 44014302 0.96 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。注意：请参阅人体工程学注意事项查看安全健康的作业规程。

Equipment:
  • 1076921-01-B Insulation Multimeter, Fluke 1508
  • 1130480-00-A Test Probes, Slim, Fluke TP38
Warning

只有完成全部所需认证的技术人员才能执行此程序。Tesla 特斯拉建议第三方服务提供商技术人员在执行此程序之前接受同等培训。有关 Tesla 技术人员要求的更多信息，或第三方主题说明，请参阅高压认证要求。处理高压线缆、母排或接头时，务必全程穿戴最低防护等级为 0(1000V) 的适当个人防护装备 (PPE)及高压绝缘手套。有关其他安全信息，请参阅技术注意事项 TN-15-92-003，高压安全意识注意事项。

Warning

执行暴露在高压之下的任何程序之前，请取下佩戴的所有首饰（手表、手链、戒指、项链、耳环、身份牌、穿刺饰品等），并取出口袋中的所有物品（钥匙、硬币、钢笔、铅笔、工具、钮扣等）。

Warning

Proper personal protective equipment (PPE) is required to perform this procedure:

  • High voltage insulating gloves
  • Leather glove protectors
  • High voltage glove tester
  • Safety glasses
  • Electrical hazard rated safety shoes
Warning

A glove inflator is the only recommended way to test HV gloves. Both HV gloves must pass testing before beginning this procedure. If either glove does not pass the air check, discard the pair.

Warning

Make sure that the HV gloves are not expired. HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12-month period.

拆卸

  1. Remove the charge port assembly. See 充电端口（拆卸和更换）（国标） ((拆卸和更换)).
    Note
    拆卸过程中，执行部分步骤时需要格外小心。请观看动画以获取详细指导。
  2. Remove the LH tail lamp. See 尾灯 - 左侧（拆卸和安装）.
  3. Disconnect the charge port door harness connector from the charge port ECU, and then release the charge port door grommet from the body.
  4. Apply masking tape around the charge port door area.
  5. Release the clips that attach the charge port door assembly to the vehicle, then push the bottom of the assembly out to remove the charge port door assembly from the vehicle.
    Note
    Maneuver the actuator around body to ease the removal of the charge port door assembly. Use caution when removing.

安装

  1. Install the charge port door assembly on the vehicle.
    Note
    Maneuver the actuator around body to ease the installation of the charge port door assembly. Use caution when installing.
  2. Install the charge port door grommet on the body and connect the charge port door harness connector to the charge port ECU.
  3. Install the LH tail lamp. See 尾灯 - 左侧（拆卸和安装）.
  4. Install the charge port door assembly. See 充电端口（拆卸和更换）（国标） ((拆卸和更换)).
  5. Remove the masking tape around the charge port door.