Harness - Body - LH (LHD) (7-Seat) ((拆卸和更换))

Open all four doors

Lower all four windows

Move LH front seat forward

Move RH front seat forward

Partially remove lower portion of LH rear door seal

Remove LH lower C-pillar trim

注

8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips

Fold down 2nd row 60 seatback assembly

注

Press button, fold forwards

Disconnect 2nd row 60 seat connector

注

1x connector,

Move 60 seat forward using towel bar

注

With one hand on towel bar pull up and slide the seat forward with your other hand

Remove 60 seat rear outboard track fastener

注

1x patch bolt, 11mm, 37 Nm, Discard after removal

Remove 60 seat rear inboard track fasteners

注

2x patch bolts, 11mm, 37 Nm, Discard after removal

Move 60 seat fully rearward using towel bar

注

pull up bar, slide seat forward

Remove 60 seat outboard track cover

注

1x clip, Slide covers forward to release from 60 seat tracks

Remove center track cover from 2nd row seats

注

2x clips, Slide covers forward to release from 2nd row seat tracks

Release cabin carpet from 60 seat

注

Pull cabin carpet towards front of vehicle

Remove 60 seat front inboard track fasteners

注

1x bolts, 11mm, 37 Nm, Discard after removal

Remove 2nd row 60 seat frame front outboard track fasteners

注

1x bolts, 11mm, 37 Nm, Discard after removal

Remove 2nd row 60 seat assembly from vehicle

注

Recommend assistance, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

Partially remove RH rear door seal

注

Pillar and sill trim have tabs seated underneath seal

Remove RH lower C-pillar trim

注

8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of RH rear sill trim working your way back towards rear of sill trim

Remove 40 seat outboard track cover

注

1x clip, Slide cover forward to release from 40 seat track

Release cabin carpet from 40 seat

注

Pull cabin carpet towards front of vehicle

Remove bolts securing 40 seat podium to vehicle

注

2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

Fold down 2nd row 40 seatback assembly

注

Press button, fold forwards

Move 40 seat forward using towel bar

注

With one hand on towel bar pull up and slide the seat forward with your other hand

Remove bolts securing 40 seat inner and outer tracks to vehicle

注

2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

Move 40 seat fully rearward using towel bar

注

pull bar, slide seat forward

Disconnect 2nd row 40 seat connector

注

1x connector, Newer models may have red locking tab

Remove 40 seat from vehicle

注

Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

Remove 3rd row seat cushion and disconnect harness

注

1x connector, Release LH and RH latches under cushion

Open liftgate

Release 3rd row LH seat backrest

注

Front switch at LH trunk trim panel

Release 3rd row RH seat backrest

注

Rear switch at LH trunk trim panel

Remove rear load floor

Remove trunk sill trim

注

4x clips

Remove LH load floor bracket

注

2x tabs, 2x clips, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly later

Release remaining clips and remove LH 7s trunk side trim

注

1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar, Pull the top of the trunk side trim all the way down flat so it clears the edge of the folded down LH 3rd row seatback and pull straight out

Release top edge of LH 7s trunk side trim and disconnect 12V outlet and trunk switch connectors

注

6x clips, 2x connectors

Remove LH upper C-pillar trim

注

6x clips, Guide front upper corner groove out from headliner and place trim aside

Remove RH load floor bracket

注

3x tabs, 2x clips, Confirm each installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

Remove RH trunk pocket bracket

注

1x push clip, 5x alignment tabs

Release top edge of RH trunk side trim

注

1x push clip, 13x clips, trim part may slightly differ by vehicle build location, and the number of clips may also varyt

Remove RH upper C-pillar trim

注

6x clips, Guide front upper corner groove out from headliner and place trim aside, trim part may slightly differ by vehicle build location, and the number of clips may also varyt

Remove LH mid A pillar assembly

注

1x clip, 1x tab, Release upper clip then pull mid A pillar upward to remove

Remove clip securing LH lower A pillar trim

注

1x push clip

Remove LH lower A pillar trim

注

6x clips, 2 guide tabs, Pull rear of lower A pillar upward to release clip then pull rearward to release trim panel

Partially release LH front primary door seal

Remove clip securing LH front cabin carpet to body

注

1x push clip

Pull LH front cabin carpet away from A-pillar to access LH front seat connector

Remove RH mid A pillar assembly

注

1x clip, 1x tab, Release the upper clip then pull mid A pillar upward to remove

Remove clip securing RH lower A pillar trim

注

1x push clip

Remove RH lower A pillar trim to release seat harness.

注

6x clips, 2 guide tabs, Pull rear of lower A pillar upward to release clip then pull rearward to release trim panel

Partially release RH front primary door seal

Remove clip securing RH front cabin carpet to body

注

1x clip

Pull RH front cabin carpet away from A-pillar to access RH front seat connector

Release RH front seat belt retractor from pretensioner

注

Insert special removal tool into the bottom of the retractor to release

Release LH front seat belt retractor from pretensioner

注

Insert seat belt tool into the bottom of the retractor to release

Remove LH front seat rear fasteners

注

2x patch bolts, TP45, 33.5 Nm, Discard after removal

Move LH front seat backward

注

Ensure profile is saved to allow seat position to be restored

Remove LH front seat front fasteners

注

2x patch bolts, TP45, 33.5 Nm, Discard after removal

Adjust position of LH front seat for easy removal

注

Move seat to middle of track at most upright position

Remove RH front seat rear fasteners

注

2x patch bolts, TP45, 33.5 Nm, Discard after removal

Move the RH front seat back.

Remove RH front seat front fasteners

注

2x patch bolts, TP45, 33.5 Nm, Discard after removal

Adjust position of RH front seat for easy removal

注

Move seat to middle of track at most upright position

Open the hood.

Remove the rear apron.

Power off vehicle from center display

注

Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

Disconnect the 12V negative battery cable and First Responder Loop.

Disconnect LH front seat harness from VC left

注

1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC left, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged

Remove LH front seat harness clips from LH footwell support bracket

注

2x retaining clips

Release LH front seat harness from LH front sill panel harness bracket

注

5x clips

Pull LH front seat harness from under LH front cabin carpet

Remove LH front seat from vehicle

注

Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

Disconnect RH front seat harness from VC right

注

1x electrical connector, Release the lock by squeezing the release tab,

Remove RH front seat harness from RH footwell support bracket

注

2x retaining clips

Release RH front seat harness from lower A 12V bracket

注

5x clips

Pull RH front seat harness from under RH front cabin carpet

Remove RH front seat from vehicle

注

Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

Remove LH console side panel carpet

注

10x clips, 1x guide pin, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged

Remove LH front exterior hardware from center console

注

2x bolts, 10mm, 7 Nm, The relatively newer vehicles are equipped with a T30 bolt.

Remove console lower rear panel

注

5x clips

Remove LH rear exterior hardware from center console

注

1x bolt, 10mm, 7 Nm

Remove RH rear exterior hardware from center console

注

1x bolt, 10mm, 7 Nm

Remove RH console side panel carpet

注

11x clips, 1x guide pin, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged

Remove RH front exterior hardware from center console

注

2x bolts, 10mm, 7 Nm, The relatively newer vehicles are equipped with a T30 bolt.

Disconnect harness from rear of center console

注

1x connector

Disconnect USB harness at right front of center console

注

1x USB connector

Remove center console from vehicle

注

Recommend assistance, Tilt rear of console upward, pull assembly towards rear of vehicle, then tilt front of console upward and remove through passenger side

Release LH upper B pillar assembly and move aside

注

4x clips, Pull the bottom of the upper B pillar toward inside of the vehicle then pull the top to release the remaining clips

Partially remove lower portion of LH rear door seal

Remove LH Lower C Pillar trim

注

5x clips, Rear edge is mated with groove in trunk side trim, Release clips at front of LH Lower C Pillar trim working your way back towards rear of sill trim, trim part may slightly differ, by vehicle build location,Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly later

Remove clip securing LH lower B-pillar to body

注

1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

Remove LH lower B pillar assembly

注

6x clips, Pull the top of B pillar to release, then work your way to bottom clips

Release clips securing RH upper B-pillar assembly and move aside

注

4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips

Remove clip securing RH lower B-pillar to body

注

1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

Remove RH lower B-pillar assembly

注

6x clips, Pull the top of B-pillar to release, then work your way to bottom clips

Remove rear floormat

Remove rear main cabin carpet from vehicle

注

Pull up at the rear of rear main carpet and slide back, Remove from LH rear door

Remove screw and clips securing LH footwell cover

注

2x push clips, 1x screw, T20, 2.5 Nm

Remove connectors from LH footwell cover and remove from vehicle

注

3x tabs, 1x Ethernet connector, 1x puddle light connector, APAC specific vehicles an additional ODII connector will have to be connected

Remove fasteners securing driver knee air bag to vehicle

注

2x push clips, 2x screws, T20, 2 Nm, 4x patch bolts, E10, 8 Nm, Discard after removal, Support the knee air bag while lowering, The connector / harness length is very short

Remove driver knee air bag

注

1x connector, Release locking tab, Then release squib from air bag, Support air bag while disconnecting, Connector release may vary

Remove LH footwell air duct

Remove LH front floor mat

Remove clips securing LH front cabin carpet to vehicle

注

2x push clips

Remove LH front cabin carpet from vehicle

注

Lift up rear edge of carpet then slide out towards rear of vehicle, be cautious and avoid foam below catching on seat risers

Remove LH upper A-pillar trim

注

3x clips, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove

Remove LH sun visor bracket cover

注

4x clips, Extending the sun visor may allow for extra working room

Remove LH sun visor fastener

注

1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room

Remove LH sun visor from headliner area

注

Fold sun visor to the closed and folded down position but do not latch in place

Disconnect LH sun visor connector

注

1x connector

Remove RH upper A-pillar trim

注

3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove

Remove RH sun visor bracket cover

注

4x clips, Extending the sun visor may allow for extra working room

Remove RH sun visor fastener

注

1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room

Remove RH sun visor from headliner area

注

Fold sun visor to the closed and folded down position but do not latch in place

Disconnect RH sun visor connector

注

1x connector

Remove lower quad camera cover

注

4x tabs, Squeeze on both sides of the cover and pull downward away from mirror

Remove tether from lower quad camera cover

注

1x hook, Guide hook through anchor on quad cam cover

Disconnect rear view mirror connector

注

1x connector

Remove rear view mirror

注

Turn mirror counterclockwise to remove, Do not twist by holding the mirror itself, ball joint will de-couple, Twist from the stalk connecting the mirror to the mount

Push open LH coat hook

Open LH coat hook screw cover

注

1x locking tab

Remove LH coat hook screw

注

1x screw, T20, 1.0 Nm

Push open RH coat hook

Open RH coat hook screw cover

注

1x locking tab

Remove RH coat hook screw

注

1x screw, T20, 1.0 Nm

Release headliner from body

注

11x clips, Recommend assistance, Headliner will be partially supported by safety tethers at B-pillars and 2x tether clips at rear corners

Disconnect J5 body connector

注

1x connector, Release lock then remove

Disconnect J2 body connector

注

1x connector, Release lock then remove

Disconnect J4 body connector

注

1x connector, Release lock then remove

Disconnect brake switch

注

1x connector

Connect accelerator pedal connector

注

1x connector, Engage locking tab

Remove accelerator and brake pedal harness clips

注

4x clips

Disconnect headliner harness

注

1x connector

Disconnect white connector X909 from front harness

注

1x connector

Remove LH body harness clips from LH A-pillar

注

3x clips

Release clips securing for LH body harness from below LH front seat

注

3x clips

Remove LH harness clips under front seats and center console

注

3x clips

Disconnect LH body harness from RCM

注

1x connector

Disconnect LH harness from RH body Harness

注

2x connectors,1x clip,Release red locking tabs

Disconnect the LH body harness connectors around lower B-pillar area

注

4x connectors, LH rear door harness, acceleration sensor, and LH seat belt

Remove the LH harness ground strap around LH lower B-pillar area

注

1x bolt, 10mm, 10 Nm

Remove LH harness clips from B-pillar area

注

6x clips

Remove LH B-pillar applique from body

注

1x fir tree clip, 2x clips, 2x connectors, Pull straight outwards to release from B-Pillar, disconnect camera connector then remove from vehicle, Use caution not to damage the connectors

Remove the LH body harness clips around the below C-pillar area

注

4x clips

Disconnect 2nd row 60 seat connector

注

1x connector,

Disconnect LH 2nd row retractor connector

注

1x connector, 2 stage locking connector, Lift the red locking tab then release the connector

Remove the LH body harness clips around C-pillar area

注

4x clips

Disconnect LH side curtain air bag and liftgate power strut electrical connector from LH body harness

注

2x connectors

Release connectors from LH body harness to charge port ECU

注

2x connectors

Remove LH body harness clips around LH side trunk area

注

3x clips

Disconnect connectors from chargeport assembly

注

3x connectors, 1x red locking tab, 2x white locking tab

Remove the LH body harness ground strap below LH tail lamp

注

1x bolt, 10mm, 10 Nm

Remove LH liftgate stop

注

1x liftgate stop, Pull up to remove

Disconnect LH rear bodyside tail lamp assembly

注

1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

Release LH rear bodyside tail lamp assembly

注

2x nuts, 8mm, 3.2 Nm

Remove LH rear bodyside tail lamp assembly from vehicle

注

2x studs, To ease removal use trim tool to release lamp from body near each stud. While releasing studs, Pull from opposite end of lamp.

Remove bolt securing LH corner of rear fascia to body

注

1x bolt, 10mm, 4 Nm

Remove RH liftgate stop

注

1x liftgate stop, Pull up to remove

Disconnect RH rear bodyside tail lamp assembly connector

注

1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

Remove nuts securing RH rear bodyside tail lamp assembly to vehicle

注

2x nuts, 8mm, 3.2 Nm

Remove RH rear bodyside tail lamp assembly from vehicle

注

2x studs

Remove bolt securing RH corner of rear fascia to body

注

1x bolt, 10mm, 4 Nm

Release rear fascia from rear diffuser

注

6x clips, 7x bolts, 10mm, 4 Nm

Remove LH rear fender garnish from vehicle

注

14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish

Remove bolt securing LH rear fascia to body

注

1x bolt, 8mm, 4 Nm

Remove RH rear fender garnish from vehicle

注

14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish

Remove bolt securing RH rear fascia to body

注

1x bolt, 8mm, 4 Nm

Release rear fascia from body and disconnect rear fascia harness then remove assembly from vehicle

注

1x connector, Slide red locking tab away from connector, Then depress black locking tab to release the connector. Recommend assistance, Place rear fascia on padded surface to avoid damage. Not need to disconnect rear fascia connector for AP4.

Remove rear body harness from rear fascia center bracket

注

4x clips, 1 of 4 clips located behind LH side connector in 1st image

Disconnect rear BLE

注

1x connector, 2 stage locking connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

Disconnect rear subframe and LH rear EPB connectors

注

2x connectors

Push the rear subframe portion of the LH body harness through the LH side trunk bulkhead

注

Harness passes through into trunk near rear section of LH rear wheel liner area

Remove the LH body harness from vehicle

Position the LH body harness into vehicle for installation

Push the rear harness seal through body and fully seat

注

Harness passes through into trunk near rear section of LH rear wheel liner area

Connect rear subframe and LH rear EPB connector

注

2x connectors

Connect rear BLE

注

1x connector, Engage locking tab

Install rear body harness onto rear fascia center bracket

注

4x clips

Connect and install rear fascia onto vehicle

注

1x connector, Engage red locking tab, Recommend assistance, Verify lower portion aligns with rear diffuser. Not need to connect rear fascia connector for AP4.

Apply Loctite 222 onto rear diffuser bolts and secure rear fascia to rear diffuser

注

6x clips, 7x bolts, 10mm, 4 Nm

Install bolt securing RH rear fascia to body

注

1x bolt, 8mm, 4 Nm

Install RH rear fender garnish

注

14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

Install bolt securing LH rear fascia to body

注

1x bolt, 8mm, 4 Nm

Install LH rear fender garnsih

注

14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

Install bolt securing RH corner of rear fascia

注

1x bolt, 10mm, 4 Nm

Remove RH bodyside lamp connector gasket

注

1x gasket

Install RH bodyside lamp connector gasket

注

1x gasket

Remove upper T-stud gasket from RH bodyside lamp

注

1x gasket

Install upper T-stud gasket to RH bodyside lamp

注

1x gasket

Remove lower T-stud gasket from RH bodyside lamp

注

1x gasket

Install lower T-stud gasket to RH bodyside lamp

注

1x gasket

Install RH rear bodyside tail lamp assembly into vehicle

注

2x studs

Install nuts securing RH rear bodyside tail lamp assembly to vehicle

注

2x nuts, 8mm, 3.2 Nm

Connect RH rear bodyside tail lamp assembly

注

1x connector, Engage locking tab

Install RH liftgate stop

注

1x liftgate stop, Align tab and push down to secure

Install bolt securing LH corner of rear fascia

注

1x bolt, 10mm, 4 Nm

Remove LH bodyside lamp connector gasket

注

1x gasket

Install LH bodyside lamp connector gasket

注

1x gasket

Remove upper T-stud gasket from LH bodyside lamp

注

1x gasket

Install upper T-stud gasket to LH bodyside lamp

注

1x gasket

Remove lower T-stud gasket from LH bodyside lamp

注

1x gasket

Install lower T-stud gasket to LH bodyside lamp

注

1x gasket

Install LH rear bodyside tail lamp assembly into vehicle

注

2x studs

Install LH rear bodyside tail lamp assembly to vehicle

注

2x nuts, 8mm, 3.2 Nm

Connect LH rear bodyside tail lamp assembly

注

1x connector, Engage locking tab

Install LH liftgate stop

注

1x liftgate stop, Align tab and push down to secure

Install the LH body harness ground strap below LH tail lamp

注

1x bolt, 10mm, 10 Nm

Install logic connectors to charge port assembly

注

3x connectors, 1x red locking tab, 2x white locking tab

Install LH body harness clips around LH side trunk area

注

3x clips

Install connectors from LH body harness to charge port ECU

注

2x connectors

Connect LH side curtain air bag and liftgate power strut electrical connector to LH body harness

注

2x connectors

Install the LH body harness clips around upper C-pillar area

注

4x clips

Connect LH 2nd row retractor connector

注

1x connector, 2 stage locking connector, Engage the red locking tab when the connector is fully seated

Install the LH body harness clips around the below C-pillar area

注

4x clips

Install LH B-pillar applique to vehicle

注

2x connectors, 1x fir tree clip, 2x clips, Align B-Pillar applique into position and secure clips into body, Use caution not to damage the connectors

Install LH harness clips onto B-pillar area

注

6x clips

Connect the LH body harness connectors around lower B-pillar area

注

4x connectors, LH rear door harness, acceleration sensor, and LH seat belt

Install the LH harness ground strap around LH lower B-pillar area

注

1x bolt, 10mm, 10 Nm

Connect LH harness to RH body Harness

注

2x connector,1x clip,Engage locking tabs

Install LH body harness to RCM

注

1x connector

Install LH harness clips under LH front seat and RH lower B-pillar area

注

3x clips

Install securing clips LH body harness beiow LH front seat

注

3x clips

Install LH body harness clips to LH A-pillar

注

3x clips

Connect J5 body connector

注

1x connector, Fully seat connector then engage lock

Connect J2 body connector

注

1x connector, Fully seat connector then engage lock

Connect J4 body connector

注

1x connector, Fully seat connector then engage lock

Connect white connector X909 to front harness

注

1x connector

Connect headliner harness

注

1x connector

Install accelerator and brake pedal harness clips

注

4x clips

Connect accelerator pedal connector

注

1x connector, Engage locking tab

Connect brake switch connector

注

1x connector

Install LH footwell duct into HVAC module

注

1x clip

Install driver knee air bag

注

1x connector, Engage locking tab, Use caution not to damage connector/harness, Support air bag while connecting connector

Install fasteners securing driver knee air bag to vehicle

注

4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 2x push clips

Install headliner to body

注

11x clips, Recommend assistance, Seat 2x clips at coat hooks when replacing headliner, Reseat primary seal at doors and liftgate to headliner

Install rear view mirror

注

1x bolt, T20, 2.5 Nm, Install new bolt, Rear mirror mount may vary depending on build date, If mirror is NOT equipped or secured with fastener, Position mirror onto mount, Turn mirror clockwise to install, Do not twist by holding the mirror itself, Mirror will separate from the stalk, Twist from the stalk connecting the mirror to the mount

Connect rear view mirror connector

注

1x connector

Install tether onto lower quad camera cover

注

1x hook, Guide hook through anchor on quad cam cover

Install quad camera lower cover

注

4x tabs, Pinch upper portion of trim and engage into locking tabs

Connect RH sun visor connector

注

1x connector

Install RH sun visor into headliner area

注

Fold sun visor to the closed and folded down position but do not latch in place

Install RH sun visor fastener

注

1x screw, T25, 3.5 Nm

Install RH sun visor bracket cover

注

4x clips

Install RH upper A-pillar trim

注

3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

Connect LH sunvisor connector

注

1x connector

Install LH sun visor into headliner area

注

Fold sun visor to the closed and folded down position but do not latch in place

Install LH sun visor fastener

注

1x screw, T25, 3.5 Nm

Install LH sun visor bracket cover

注

4x clips

Install LH upper A-pillar trim

注

3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

Install LH coat hook screw

注

1x screw, T20, 1.0 Nm

Close LH coat hook screw cover

注

1x locking tab

Push LH coat hook closed

Install RH coat hook screw

注

1x screw, T20, 1.0 Nm

Close RH coat hook screw cover

注

1x locking tab

Push RH coat hook closed

Install LH upper C-pillar trim

注

6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim

Position LH 7s trunk side trim and install lower clips

注

1x push clips, 5x clips, Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly, Guide front clip stanchions around LH C-pillar

Install LH 7s trunk side trim

注

6x clips, 2x connectors, Connect 12V outlet and trunk switch connectors then install top edge of LH 7s trunk side trim

Install LH trunk pocket bracket

注

1x push clip, 5x alignment tabs

Install LH load floor bracket

注

3x tabs, 2x clips, Confirm each installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

Install RH upper C-pillar trim

注

6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarterglass, Seat trunk seal to edge of trim, trim part may slightly differ by vehicle build location, and the number of clips may also varyt

Install RH trunk side trim

注

1x push clip, 13x clips, Guide front clip stanchions around RH C-pillar, trunk seal to edge of trim, trim part may slightly differ by vehicle build location, and the number of clips may also varyt

Install RH trunk pocket bracket

注

1x push clip, 5x alignment tabs

Install RH load floor bracket

注

3x tabs, 2x clips, Confirm each installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

Install rear load floor

Install trunk sill trim

注

4x clips, Seat seal around edge of trim

Install rear main cabin carpet to vehicle

注

Position rear main carpet to floorboard and slide forward, Ensure rear main carpet tucks beneath front main carpet and air duct

Install rear floormat

Install LH front cabin carpet

Install clips securing LH front cabin carpet to vehicle

注

2x push clips

Install 2nd row 60 seat assembly

注

Recommend assistance

Connect 2nd row 60 seat connector

注

1x connector,

Install fasteners securing 60 seat frame to body

注

5x patch bolts, 11mm, 37 Nm, Install new patch bolts, bottom seat bolts located in rear

Secure cabin carpet to 60 seat

注

Strap velcro on

Move 2nd row 60 seatback to vertical position

注

Remove seat back protection if necessary

Install 60 seat outboard track cover

注

1x clip

Install LH lower C-pillar trim

注

8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips

Reseat LH rear door seal

注

Seat pillar and sill trim tabs underneath seal

Install 40 seat into vehicle

注

Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium

Connect 2nd row 40 seat connector

注

1x connector,

Install bolts securing 40 seat podium to vehicle hand tight

注

2x patch bolts, 11mm, 37 Nm, Install new bolts, Torque at later step

Move 40 seat forward using towel bar

注

pull up bar, slide seat forward

Install bolts securing 40 seat inner and outer tracks to vehicle

注

2x patch bolts, 11mm, 37 Nm, Install new bolts

Move 40 seat to original position

注

Press shoulder switch then pull seat backward

Torque bolts securing 40 seat podium to vehicle

注

2x patch bolts, 11mm, 37 Nm

Install rear cabin carpet to 40 seat

Install center track cover to 2nd row seats

注

2x clip, Slide cover straight on to clip to 2nd row seat tracks

Install 40 seat outboard track cover

注

1x clip

Install RH lower c-pillar trim

注

4x tabs, 3x clips, 5x location pins, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips

Reseat RH rear door seal

注

Seat pillar and sill trim tabs underneath seal

Install 3rd row seat cushion and connect harness

注

1x connector, Secure LH and RH latches under cushion

Install LH footwell cover

注

5x clips, 1x push clip, 1x Ethernet connector, 1x connector, 1x OBD, T20, 2.5 Nm

Install screw and clips securing LH footwell cover

注

1x screw, T20, 2.5 Nm, 2x push clips

Install RH lower B-pillar assembly

注

7x clips, 2x tabs, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips

Install clip securing RH lower B-pillar to body

注

1x push clip, Clip goes through B-pillar and rear cabin carpet

Install RH C-pillar lower trim

注

5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips, Confirm installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

Install RH upper B-pillar assembly

注

4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim

Install LH lower B pillar assembly

注

7x clips, 2x tabs, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips

Install clip securing LH lower B pillar to body

注

1x push clip, Clip secures lower B pillar and rear cabin carpet to body

Remove LH Lower C Pillar trim

注

5x clips, Rear edge is mated with groove in trunk side trim, Release clips at front of LH Lower C Pillar trim working your way back towards rear of sill trim, trim part may slightly differ, by vehicle build location,Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly later

Reseat LH rear door seal

注

Seat pillar and sill trim tabs underneath seal

Install LH upper B pillar assembly

注

4x clips, Lower the seat belt slider to align it with the B pillar panel, Insert top portion of upper B pillar under the headliner to align the clips, Press the bottom to fully seat upper B pillar to lower B pillar, Make sure the seal correctly overlaps the trim

Install center console onto vehicle

注

Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place

Connect harness at right front of center console

注

1x USB connector

Connect harness to rear of center console

注

1x connector

Install RH front exterior hardware to center console

注

2x bolts, 10mm, 7 Nm, The relatively newer vehicles are equipped with a T30 bolt.

Install RH console side panel carpet

注

11x clips, 1x guide pin, Position side panel and align the locator, then the rear locator, Push side panel towards console to install

Install RH rear exterior hardware to center console

注

1x bolt, 10mm, 7 Nm

Install LH rear exterior hardware to center console

注

1x bolt, 10mm, 7 Nm

Install console lower rear panel

注

5x clips

Install LH front exterior hardware to center console

注

2x bolts, 10mm, 7 Nm, The newer vehicles are equipped with a T30 bolt.

Install LH console side panel carpet

注

10x clips, 1x guide pin, Position side panel and align the locator, then the rear locator, Push side panel towards console to install

Secure LH front seat harness under LH front cabin carpet

Install LH front seat harness along LH front sill panel harness bracket

注

5x clips

Install LH front seat harness clips onto LH footwell support bracket

注

2x retaining clips

Connect LH front seat harness to VC left

注

1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated

Fully seat LH front cabin carpet

Install clip securing LH front cabin carpet to body

注

1x push clip

Install LH lower A pillar trim

注

6x clips, 2 locating pins, Align front locating pin first

Install clip securing LH lower A pillar trim

注

1x push clip

Install LH mid A pillar assembly

注

1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A pillar, Pull seal over trim

Reseat LH front door seal along lower A pillar trim

Install RH front seat into vehicle

注

Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim, Gateway configuration update for cfg_frontSeattype is needed when replacing from 7654324-XX-C to 7654324-XX-F or newer 1st Row LHD RH Seat Assembly with 1st Row Mini-Tilt Motor Assembly

Secure RH front seat harness under RH front cabin carpet