교정 코드 NEW 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

1. Open LH front door

   

2. Lower LH front window

   

3. Move LH front seat backward

   

4. Open RH front door

   

5. Lower RH front window

   

6. Move RH front seat backward

   

7. Open hood

   

   

8. Power off vehicle from center display
   참고

   Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

   

   

9. Remove rear underhood apron
   참고

   14x clips

   

   

10. Disconnect LV battery and First Responder Loop
    참고

    2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

    

    

    

11. Partially release LH front primary door seal
    참고

    Release lower section of LH front primary door seal

    

12. Remove LH IP end cap
    참고

    5x clips, 2x guide tabs

    

    

13. Remove LH upper A-pillar trim
    참고

    6x clips, 1x tether, 2x guide tabs, 1x alignment pin, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove

    

    

    

    

14. Release LH footwell cover
    참고

    2x magnets,1x guide tab

    

15. Remove connectors from LH footwell cover
    참고

    1x connector, 1x OBDII connector, Release OBDII connector by depressing tabs from front side

    

    

16. Remove LH knee airbag bolt covers
    참고

    2x covers

    

    

17. Remove LH knee air bag bolts
    참고

    4x bolts, EP10, 8.5 Nm, Discard bolts after removal

    

    

18. Remove LH knee airbag assembly
    참고

    1x connector, Peel back plastic film, Release by pulling back both white tabs simultaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side

    

    

    

19. Partially release RH front primary door seal
    참고

    Release the lower section of RH front primary door seal

    

20. Remove RH IP end cap
    참고

    5x clips, 2x guide tabs

    

    

21. Remove RH upper A-pillar trim
    참고

    6x clips, 1x tether, 2x guide tabs,1x alignment pin, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove

    

    

    

    

22. Release RH footwell cover
    참고

    2x magnets, 1x guide tab, 1x connector

    

    

23. Remove RH knee airbag bolt covers
    참고

    2x covers

    

    

24. Remove RH knee air bag bolts
    참고

    4x bolts, EP10, 8.5 Nm, Discard bolts after removal

    

    

25. Remove RH knee airbag assembly
    참고

    1x airbag connector, 1x connector, Peel back plastic film, Release by pulling back both white tabs simultaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side

    

    

    

    

26. Remove clips securing passenger footwell duct
    참고

    2x clips

    

27. Disconnect glove box USB cable from car computer
    참고

    1x connector, Release locking tab then release connector

    

28. Remove screws securing glove box to IP
    참고

    4x screws, T20, 2.3 Nm

    

    

    

29. Release glove box from IP carrier
    참고

    10x clips, 3x locator pins, 1x datum, Avoid damage to electromagnetic switch

    

    

30. Disconnect glove box connectors
    참고

    2x connectors

    

    

31. Remove RH passenger footwell duct from HVAC module

    

    

32. Disconnect RH IP air wave duct thermistor connector
    참고

    1x connector

    

33. Remove clips securing RH air wave duct to IP
    참고

    2x push clips

    

34. Remove RH IP air wave duct from HVAC module

    

    

35. Remove console rear end panel from center console assembly
    참고

    6x clips, 2x tabs, First release the upper clips and then release the lower tabs to remove rear end panel

    

    

    

36. Remove rear bolts securing center console to vehicle
    참고

    2x bolts, 10mm, 7 Nm

    

    

37. Remove LH front floor mat

    

38. Remove LH console side panel carpet
    참고

    11x clips, 2x positioning clips, 1x tab, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Use prytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the tab and pull out the side panel backward, Replace the clips if it is damaged

    

    

    

    

    

    

39. Remove LH front exterior bolts from center console
    참고

    2x bolts, 10mm, 7 Nm

    

40. Remove RH front floor mat

    

41. Remove RH console side panel carpet
    참고

    12x clips, 2x positioning clips, 1x datum, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Use prytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the datum and pull out the side panel backward, Replace the clips if it is damaged

    

    

    

    

    

    

42. Remove RH front exterior bolts from center console
    참고

    2x bolts, 10mm, 7 Nm

    

43. Disconnect harness from rear of center console
    참고

    1x connector, 1x clip

    

    

44. Disconnect harness connector from right front of center console
    참고

    1x connector, 1x clip

    

    

45. Remove center console assembly from vehicle
    참고

    Recommend assistance, Tilt rear of console upward, pull assembly towards rear of vehicle, then tilt front of console upward and remove through passenger side, Then Place on the work table

    

    

46. Remove screws securing IP lower assembly to IP carrier
    참고

    1x screw, T20, 2.3 Nm

    

47. Remove IP lower assembly from IP carrier
    참고

    13x tabs

    

    

48. Release spring clip securing driver air bag assembly to steering wheel and pull driver air bag assembly away from steering wheel
    참고

    2x spring clips, 2x datums, Press the spring simultaneously from two access holes to release, Access holes located at 4 and 8 o’clock position, Do not insert tool too far as air bag connector could be damaged

    

    

    

    

    

49. Disconnect driver air bag connector and remove driver air bag assembly
    참고

    1x connector

    

    

50. Disconnect steering wheel connector
    참고

    1x connector

    

51. Remove bolt securing steering wheel to steering column
    참고

    1x patch bolt, 10mm hex, 80 Nm, Discard after removal, Counter hold the steering wheel when breaking bolt loose

    

52. Mark the steering wheel to steering column
    참고

    Align the marking during installation

    

53. Remove steering wheel from steering column

    

    

54. Pull upward to release steering column upper shroud from lower shroud
    참고

    4x alignment clips,4x guide tabs

    

    

55. Remove upper screws securing lower shroud to steering column module
    참고

    2x screws, T20, 1.5 Nm

    

56. Remove lower shroud from steering column
    참고

    1x locator slot

    

    

57. Disconnect steering column control module (SCCM) assembly connector
    참고

    1x connector, Remove retaining clip on the connector, release connector, then remove the remaining broken clip from connector, Discard retaining clip after removal, Originally installed clip is black, Replacement clip is orange

    

    

58. Remove bolt securing SCCM to steering column
    참고

    1x bolt, T20, 2.4 Nm

    

59. Remove SCCM from steering column

    

    

60. Release IP service panel from IP
    참고

    4x tabs, 2x guide pins,

    

    

61. Disconnect temperature sensor connector
    참고

    1x connector

    

62. Remove bolts securing center display to IP carrier
    참고

    2x patch bolts, 10mm, 16 Nm, Discard after removal, Slide towards rear of vehicle to remove

    

    

63. Disconnect harness connectors from center display
    참고

    2x connectors

    

64. Remove center display from vehicle

    

65. Release clips securing defroster grill
    참고

    9x metal clips, 2x guide tabs

    

    

66. Disconnect defroster grill ambient light connectors
    참고

    2x connectors

    

67. Remove defroster grill from vehicle

    

68. Remove LH IP speaker
    참고

    3x screws, T20, 2.3 Nm, 1x connector

    

    

    

69. Remove center IP speaker
    참고

    3x screws, T20, 2.3 Nm, 1x connector

    

    

    

70. Remove RH IP speaker
    참고

    3x screws, T20, 2.3 Nm, 1x connector

    

    

    

71. Disconnect connectors for passenger air bag
    참고

    3x connectors, 2 stage locking connectors, Lift the white tab to release the connector

    

    

72. Remove screws securing IP carrier to cross car beam near passenger air bag
    참고

    2x patch bolts, E10, 8 Nm, Discard after removal

    

73. Release IP harness from cross car beam
    참고

    1x slot

    

74. Disconnect IP harness connector from IP RH side
    참고

    1x connector

    

75. Remove screw securing IP carrier to cross car beam on upper LH side
    참고

    1x screw, T20, 2.3 Nm, 1x datum

    

    

76. Remove screws securing IP carrier to cross car beam on lower LH side
    참고

    3x screws, T20, 2.3 Nm, 2x datums

    

    

77. Remove screws securing IP carrier to cross car beam at lower center
    참고

    3x screws, T20, 2.3 Nm, 3x datums

    

    

    

    

    

78. Remove screw securing IP carrier to cross car beam on upper RH side
    참고

    1x screw, T20, 2.3 Nm, 1x datum

    

    

79. Disconnect IP harness connector from IP LH side
    참고

    1x connector, Gently pull out the left instrument panel and lift it to facilitate disconnect the connector

    

    

80. Remove IP carrier from vehicle
    참고

    4x guide tabs, 2x tabs, Recommend assistance

    

    

    

81. Remove clips securing RH air wave duct to IP
    참고

    2x push clips

    

82. Remove RH IP air wave duct from HVAC module

    

    

83. Remove clips securing RH front main carpet to vehicle
    참고

    1x clip, Number of clips on new vehicles may vary

    

84. Remove bolt securing RH cross car beam bracket to cross beam
    참고

    1x bolt, 13mm, 25 Nm

    

85. Remove nut securing RH cross car beam bracket to body
    참고

    1x nut, 13mm, 25 Nm

    

86. Remove RH cross car beam bracket from vehicle

    

    

87. Disconnect HVAC connector from LH body controller
    참고

    1x connector

    

    

88. Disconnect IP harness J10 connector from LH body controller
    참고

    1x connector, release lock then remove, pay attention on the color and location of the connector

    

    

89. Remove harness clip from IP near LH controller
    참고

    1x harness clip

    

90. Remove the HVAC harness fixing clip from the instrument mount bracket
    참고

    2x harness holding mounts

    

91. Disconnect IP harness connector from electronic steering column
    참고

    1x connector

    

92. Remove bracket securing the connector to crossbeam
    참고

    2x Bracket buckle

    

93. Remove SCCM wiring harness clip from crossbeam

    

94. Disconnect blower motor connector
    참고

    1x connector

    

95. Remove blower motor harness clips from cross beam
    참고

    2x harness clips

    

96. Remove IP harness clips from the top of the cross car beam and release HVAC harness from IP harness
    참고

    4x harness clips 1x harness holder, Number of clips on newer vehicles may vary

    

    

97. Remove UI harness fixing clip from crossbeam
    참고

    1x harness clip

    

98. Remove the wiring harness fixing clip from the lower part of the dashboard Cross Car Beam
    참고

    4x harness clips, Number of clips on newer vehicles may vary

    

99. Remove RH wiring harness from instrument panel mounting bracket
    참고

    2x harness holding mounts

    

100. Disconnect IP harness to J10 connector of RH control
     참고

     1x connector

     

     

101. Remove IP harness clips from body
     참고

     4x harness clips

     

102. Disconnect IP harness connector from RCM
     참고

     1x connector, Release locking tab then pivot lever

     

103. Remove instrument panel wiring harness from bottom area of center console area and move it aside

     

104. Remove IP harness from cross car beam
     참고

     Take note of IP harness routing for installation

     

105. Position IP harness to cross car beam for installation

     

106. Install instrument panel wiring harness from lower area of the center console and position it onto vehicle

     

107. Connect HVAC connector to LH body controller
     참고

     1x connector

     

108. Connect IP harness J10 connector to LH body controller
     참고

     1x connector, fully seat connector then engage lock

     

109. Install harness clip from IP near LH controller
     참고

     1x harness clip

     

110. Install the HVAC harness fixing clip from the instrument mount bracket
     참고

     2x harness holding mounts

     

111. Install SCCM wiring harness clip to crossbeam

     

112. Install connector onto crossbeam
     참고

     2x Bracket buckle

     

113. Connect IP harness connector to electronic steering column
     참고

     1x connector

     

114. Install IP harness clips from the top of the cross car beam and release HVAC harness from IP harness
     참고

     4x harness clips 1x harness holder, Number of clips on newer vehicles may vary

     

     

115. Install UI harness fixing clip onto crossbeam
     참고

     1x harness clip

     

116. Install clips securing blower motor harness to cross beam
     참고

     2x clips

     

117. Connect blower motor connector
     참고

     1x connector

     

118. Install wiring harness fixing clip from the lower part of the dashboard Cross Car Beam
     참고

     4x harness clips, Number of clips on newer vehicles may vary

     

119. Install RH wiring harness from the instrument panel mounting bracket
     참고

     2x harness holding mounts

     

120. Install clips securing IP harness to body
     참고

     4x clips

     

121. Connect IP harness connector to RCM
     참고

     1x connector, Position lever then secure locking tab

     

     

122. Connect IP harness to J10 connector of RH control
     참고

     1x connector, J10

     

123. Position RH cross car beam bracket to vehicle for installation

     

     

124. Install nut securing RH cross car beam bracket to body
     참고

     1x nut, 13mm, 25 Nm

     

125. Install bolt securing RH cross car beam bracket to cross car beam
     참고

     1x bolt, 13mm, 25 Nm

     

126. Install clips securing RH front main carpet to vehicle
     참고

     1x clip, Number of clips on new vehicles may vary

     

127. Install IP LH air wave duct into HVAC assembly

     

     

128. Install clips securing IP LH air wave duct to cross car beam
     참고

     2x push clips

     

129. Install IP carrier onto cross car beam
     참고

     4x guide tabs, 2x tabs, Recommend assistance, Be careful not to press the speaker connector and ambient light connector onto the IP

     

     

     

130. Connect IP harness connector from IP LH side
     참고

     1x connector, Gently pull out the left instrument panel and lift it to facilitate connect the connector

     

     

131. Install screw securing IP carrier to cross car beam on upper RH side
     참고

     1x screw, T20, 2.3 Nm, 1x datum

     

     

132. Install screws securing IP carrier to cross car beam at lower center
     참고

     3x screws, T20, 2.3 Nm, 3x datums

     

     

     

     

     

133. Install screw securing IP carrier to cross car beam on upper LH side
     참고

     1x screw, T20, 2.3 Nm, 1x datum

     

     

134. Install screws securing IP carrier to cross car beam on lower LH side
     참고

     3x screws, T20, 2.3 Nm, 2x datums

     

     

135. Connect IP harness connector to IP RH side
     참고

     1x connector

     

136. Fasten IP harness to cross car beam
     참고

     1x slot

     

137. Connect passenger air bag connectors
     참고

     3x connectors, Ensure connector is fully seated, When the connector is fully seated an audible click will be heard

     

     

138. Install screws securing IP carrier to cross car beam near passenger air bag
     참고

     2x patch bolts, E10, 8 Nm, Install new bolts

     

139. Install RH IP speaker
     참고

     3x screws, T20, 2.3 Nm, 1x connector

     

     

     

140. Install center IP speaker
     참고

     3x screws, T20, 2.3 Nm, 1x connector

     

     

     

141. Install LH IP speaker
     참고

     3x screws, T20, 2.3 Nm, 1x connector

     

     

     

142. Position defroster grill into position on IP carrier

     

143. Connect defroster grill ambient light connectors
     참고

     2x connectors

     

144. Fasten clips securing defroster grill
     참고

     9x metal clips, 2x guide tabs

     

     

145. Position center display into vehicle

     

146. Connect center display connectors
     참고

     2x connectors

     

147. Install center display to IP carrier
     참고

     2x patch bolts, 10mm, 16 Nm, Install new patch bolts, Slide towards front of vehicle

     

     

148. Connect temperature sensor connector
     참고

     1x connector

     

149. Install IP service panel
     참고

     4x tabs, 2x guide pins

     

     

     

150. Install SCCM onto steering column

     

     

151. Install bolt securing SCCM to steering column
     참고

     1x bolt, T20, 2.4 Nm

     

152. Connect steering column control module (SCCM) assembly connector
     참고

     1x connector, Install new orange retaining clip to connector then install SCCM connector, Perform push-pull-push to make sure connector is seated properly

     

     

153. Install lower shroud onto steering column
     참고

     1x locator slot

     

     

154. Install upper screws securing lower shroud to steering column module
     참고

     2x screws, T20, 1.5 Nm

     

155. Align clips then press downward to install upper shroud onto lower shroud
     참고

     4x alignment clips,4x guide tabs

     

     

156. Align steering wheel to steering column then position it for installation
     참고

     The steering wheel and column are keyed

     

     

     

157. Install bolt securing steering wheel to steering column
     참고

     1x patch bolt, 10mm hex, 80 Nm, Install new patch bolt

     

158. Connect steering wheel connector
     참고

     1x connector

     

159. Connect driver air bag assembly connector
     참고

     1x connector, Make sure that the driver air bag harness doesn’t get caught between the driver air bag and the horn mechanism

     

     

160. Secure driver air bag assembly to steering wheel
     참고

     2x spring clips, 2x datums, Position driver air bag onto steering wheel, Align datums onto clips, Press down on one side of air bag until clip is fully seated, then repeat on other side, You should hear an audible click, Perform pull test on each side of driver air bag assembly, Confirm the gap and space between driver air bag assembly to steering wheel is symmetrical

     

     

     

     

161. Install IP lower assembly to IP carrier
     참고

     13x tabs

     

     

162. Install screws securing IP lower assembly to IP carrier
     참고

     1x screw, T20, 2.3 Nm

     

163. Install center console assembly to vehicle
     참고

     Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place

     

     

164. Connect harness connector to right front of center console
     참고

     1x connector, 1x clip

     

     

165. Connect harness to rear of center console
     참고

     1x connector, 1x clip

     

     

166. Install RH front exterior bolts to center console
     참고

     2x bolts, 10mm, 7 Nm

     

167. Install RH console side panel carpet
     참고

     12x clips, 2x positioning clips, 1x datum, Position side panel and align the front datum, Push the console panel from the front towards the rear

     

     

     

     

168. Install RH front floor mat

     

169. Install LH front exterior bolts to center console
     참고

     2x bolts, 10mm, 7 Nm

     

170. Install LH console side panel carpet
     참고

     11x clips, 2x positioning clips, 1x tab, Position side panel and align the front tab, Push the console panel from the front towards the rear

     

     

     

     

171. Install LH knee airbag assembly
     참고

     1x connector, Ensure airbag connector is fully engaged, Apply knee airbag label over squib assembly

     

     

     

     

172. Install LH knee air bag bolts
     참고

     4x bolts, EP10, 8.5 Nm, Install new bolts

     

     

173. Install LH knee airbag bolt covers
     참고

     2x covers

     

174. Install connectors to LH footwell cover
     참고

     1x connector, 1x OBDII connector, Ensure tabs engage on OBDII connector

     

     

175. Install LH footwell cover
     참고

     2x magnets,1x guide tab

     

     

176. Install LH front floor mat

     

177. Install rear bolts securing center console to vehicle
     참고

     2x bolts, 10mm, 7 Nm

     

     

178. Install console rear end panel to center console assembly
     참고

     6x clips, 2x tabs, First fix the lower tabs, then the upper clips to install rear end panel

     

     

     

179. Install RH IP air wave duct to HVAC module

     

     

180. Install clips securing RH IP air wave duct
     참고

     2x push clips

     

181. Connect thermistor connector RH IP air wave duct
     참고

     1x connector

     

182. Install RH passenger footwell duct to HVAC module

     

     

183. Connect glove box assembly connectors
     참고

     2x connectors

     

     

184. Install glove box into IP carrier
     참고

     10x clips, 3x locator pin, 1x datum

     

     

185. Install screws securing glove box assembly to IP carrier
     참고

     4x screws, T20, 2.3 Nm

     

     

     

186. Connect glove box USB cable to car computer
     참고

     1x connector, Engage locking tab

     

187. Install clips securing passenger footwell duct
     참고

     2x push clips, Ensure that the footwell duct is installed in place

     

188. Install RH knee airbag assembly
     참고

     1x airbag connector, 1x connector, Ensure airbag connector is fully engaged, Place plastic film back over squib assembly

     

     

     

     

189. Install RH knee air bag bolts
     참고

     4x bolts, EP10, 8.5 Nm, Install new bolts

     

     

190. Install RH knee airbag bolt covers
     참고

     2x covers

     

     

191. Install RH footwell cover
     참고

     2x magnets, 1x guide tab, 1x connector

     

     

192. Install RH upper A-pillar trim
     참고

     6x clips, 1x tether, 2x guide tabs,1x alignment pin, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

     

     

     

     

     

     

193. Install RH IP end cap
     참고

     5x clips, 2x guide tabs

     

     

194. Install seat lower section of RH front primary seal
     참고

     Verify seal is seated properly on all trim panels

     

195. Install LH upper A-pillar trim
     참고

     6x clips, 1x tether, 2x guide tabs,1x alignment pin, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

     

     

     

     

     

     

196. Install LH IP end cap
     참고

     5x clips, 2x guide tabs

     

     

197. Install LH front primary seal
     참고

     Verify seal is seated properly on all trim panels

     

198. Connect First Responder Loop and LV battery
     참고

     2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

     

     

     

     

     

199. Install rear underhood apron
     참고

     14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

     

     

200. Close hood

     

201. Move RH front seat to original position

     

202. Raise RH front window

     

203. Close RH front door

     

204. Move LH front seat to original position

     

205. Raise LH front window

     

206. Close LH front door