2026-01-15

Parcel Shelf Extension (Front)

Correction code: 10101900702 10100103502 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair work required to perform this procedure, including the linked Collision Repair procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Add any associated mechanical procedures needed to perform this procedure.

Parts List

Quantity Description Image / Notes
1 EXTN, Parcel Shelf Front (Parcel Shelf Extension - Front)
1 ASY, Parcel Shelf Retractor
8 Structural Bulb Rivet, 6.5 mm
6 Countersunk Rivet, 4.8 mm Short
6 Flow Form Rivet S18
2 Bolt, Torx-head M6-1.00x12 ZINC ALUMINUM Tesla part number: 1008842-00-A
2 NUT, HEX, FLANGE, M6-1.0x14 Tesla part number: 1016227-00-A

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Door Assembly - Charge Port (EMEA) (Remove and Replace).
  2. Busbars - Charge Port to HV Battery (3-Phase) (Remove and Replace).
  3. Airbag - Curtain - LH (Remove and Replace).
  4. Seatbelt - 2nd Row - LH (Remove and Replace).
  5. Carpet - Rear (Remove and Replace).
  6. Cover - Rocker Panel - Lower - LH (Remove and Replace).
  7. Wheel Arch Liner - Rear - LH (Remove and Replace).
  8. Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. Carpet - Rear Trunk (1-Piece) (Remove and Replace).
  10. Trim - Side - Trunk - LH (Remove and Replace).
  11. Glass - Body - Rear Quarter - LH (Remove and Install).
  12. Glass - Backlight (Heat Pump) (Remove and Install).
  13. Striker - Door - Rear - LH (Remove and Replace).
  14. Door - Rear - LH (Remove and Install).
  15. Trunk (Remove and Install).
  16. Bracket - Rear - Center (Remove and Replace).
  17. Remove the Rear Quarter Inner (Panel).
  18. Remove the Parcel Shelf Rear Extension.
  19. Remove the original component.
    Informational PurposesAn informational icon, calling your attention
    Note
    In the following images, the Cantrail Assembly has been removed to enhance clarity. There is no need to remove the Cantrail Assembly when performing this procedure.

    Factory Spot Weld

    or Drill through factory spot welds
    Informational PurposesAn informational icon, calling your attention
    Note
    When drilling out spot welds, use a drill bit that creates a hole correctly sized for the fastener that will replace the spot weld.
  20. Prepare for installation.

    Structural Bulb Rivet, 6.5 mm

    Countersunk Rivet, 4.8 mm Short

    Bolt, Torx-head and Nut

    Flow Form Rivet S18

  21. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  22. Install the new component or components.

    Bolt, Torx-head torque to 16 Nm.

  23. Install the Rear Quarter Inner (Panel).
  24. Install the Parcel Shelf Rear Extension.
  25. Perform any necessary post-repair operations.
  26. Bracket - Rear - Center (Remove and Replace).
  27. Trunk (Remove and Install).
  28. Door - Rear - LH (Remove and Install).
  29. Striker - Door - Rear - LH (Remove and Replace).
  30. Glass - Backlight (Heat Pump) (Remove and Install).
  31. Glass - Body - Rear Quarter - LH (Remove and Install).
  32. Trim - Side - Trunk - LH (Remove and Replace).
  33. Carpet - Rear Trunk (1-Piece) (Remove and Replace).
  34. Trim - Sill Panel - Rear - LH (Remove and Replace).
  35. Wheel Arch Liner - Rear - LH (Remove and Replace).
  36. Cover - Rocker Panel - Lower - LH (Remove and Replace).
  37. Carpet - Rear (Remove and Replace).
  38. Seatbelt - 2nd Row - LH (Remove and Replace).
  39. Airbag - Curtain - LH (Remove and Replace).
  40. Busbars - Charge Port to HV Battery (3-Phase) (Remove and Replace).
  41. Door Assembly - Charge Port (EMEA) (Remove and Replace).