2026-01-15

Rear Damper Mount Assembly

Correction code: 10101910402 10101910502 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Repair Information

Review all collision repair general practices and safety documentation and wear the appropriate PPE (Personal Protective Equipment) before beginning this procedure.
Properly mount the vehicle on a frame bench when performing this procedure.

Parts List


Quantity	Description	Image / Notes
1	ASY,DAMPER MOUNT RR (Rear Damper Mount Assembly)
18	High Strength Structural Rivet, 6.5 mm
12	Structural Bulb Rivet, 6.5 mm
3	Bolt , M8x23.5	Tesla part number 1063260-00-C.

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

Remove the Panel - Aero Shield - Front (Remove and Replace).
Remove the Diffuser - Rear Fascia (Remove and Replace).
Remove the Carpet - Rear Trunk (1-Piece) (Remove and Replace).
Remove the Trim - Side - Trunk - RH (Remove and Replace).
Remove the Trim - Side - Trunk - LH (Remove and Replace).
Remove the Wheel Arch Liner - Rear - LH (Remove and Replace).
Remove the Busbars - Charge Port to HV Battery (NACS) (Remove and Replace).
Remove the Knuckle - Suspension - Rear - LH (Remove and Replace).
Remove the Link - Aft - Lower - Rear - LH (Remove and Replace).
Remove the Link - Aft - Upper - Rear - LH (Remove and Replace).
Remove the Toe Link - Rear - LH (Remove and Replace).
Remove the Link - Fore - Lower - Rear - LH (Remove and Replace).
Remove the Drop Link - Stabilizer Bar - Rear - LH (Remove and Replace).
Remove the Spring - Rear Suspension - LH (Remove and Replace).
Remove the Damper - Rear - LH (Remove and Replace).
Remove the Halfshaft - Rear Drive Unit - LH (Lubricate at Hub).
Remove the original component.
or Factory Spot Welds
or Factory SPRs

or Bolts
Prepare for installation.
Note
A red X indicates a location where a factory-installed fastener is not being replaced.

or High Strength Structural Rivets, 6.5 mm
or Structural Bulb Rivets, 6.5 mm
- A = 8 mm.
- B = 12 mm.
- C = 32 mm.
- D = 14 mm.
- E = 12 mm.
- F = 10 mm.
or Bolts
Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
Install the new component or components.
Torque the bolts to 24 Nm.
Perform any necessary post-repair operations.
Install the Halfshaft - Rear Drive Unit - LH (Lubricate at Hub).
Install the Damper - Rear - LH (Remove and Replace).
Install the Spring - Rear Suspension - LH (Remove and Replace).
Install the Drop Link - Stabilizer Bar - Rear - LH (Remove and Replace).
Install the Link - Fore - Lower - Rear - LH (Remove and Replace).
Install the Toe Link - Rear - LH (Remove and Replace).
Install the Link - Aft - Upper - Rear - LH (Remove and Replace).
Install the Link - Aft - Lower - Rear - LH (Remove and Replace).
Install the Knuckle - Suspension - Rear - LH (Remove and Replace).
Install the Busbars - Charge Port to HV Battery (NACS) (Remove and Replace).
Install the Wheel Arch Liner - Rear - LH (Remove and Replace).
Install the Trim - Side - Trunk - LH (Remove and Replace).
Install the Trim - Side - Trunk - RH (Remove and Replace).
Install the Carpet - Rear Trunk (1-Piece) (Remove and Replace).
Install the Diffuser - Rear Fascia (Remove and Replace).
Install the Panel - Aero Shield - Front (Remove and Replace).