校正代码 18401802 0.96 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

1. Log into Tesla Garage
2. Enter vehicle VIN and select "Search"
3. Check Firmware version
   注

   Firmware package installed must be 2021.36 or above for vehicle configuration update and Toolbox routine
4. Navigate to "CFG" tab on "Vitals" page
5. Check the coolant pump GTW configuration, and make sure the configuration is set to DUAL_MIX.
   警告

   The Coolant Pump Identification will depend on this new configuration.

   注

   If the configuration is set to DUAL or DUAL_SAN_P4, change the configuration to DUAL_MIX. If the gateway configuration is already set to DUAL_MIX, no further configuration is required.
6. Open LH front door
7. Lower LH front window
8. Connect to vehicle using Toolbox 3.0
9. Select "Dashboards" tab, and select "Infotainment Dashboard"
10. Select "Vehicle Configuration"
    注

    Configuration values should load automatically, if not select "Read Config" and "Run" to load
11. Select "Read Config" and select "Run" to pull current vehicle configuration, Verify configuration change was performed
    注

    Read config and verify configuration change was successful, Refresh page if required, Select ‘X’ at top right of window to close once complete
12. Scroll down to "coolantPumpType" and change to "Two coolant pumps installed, mixed pole pair batches"
13. Select "Apply Changes" and select "Run" to save updated configuration
    注

    Center display will reboot, Toolbox connection will be lost, Select ‘X’ at top right of window to close once complete
14. Select ‘Actions/Autodiag’ and search for ‘Thermal’
15. Select "Start Thermal Fluid Fill/Drain (Coolant only)", click Run and allow routine to complete
    注

    Select ‘X’ at top right of window to close once complete, Verify vehicle is in Series via Garage > Vitals > Thermal tab > Coolant loops, Thermal Fluid Fill/Drain routine has a 5 hour limit, After 5 hours routine must be performed again
16. Vehicle preparation
    注

    Ensure vehicle is not charging before the repair
17. Open hood
18. Remove rear apron
    注

    14x clips

    

    

19. Power off vehicle from center display
    注

    Via Controls > Safety & Security > Vehicle Power > Power Off
20. Disconnect 12V negative terminal and first responders loop
    注

    1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

21. Remove fresh air intake duct
    注

    1x bolt, 10mm, 4 Nm, 2x clips, 1x pin, Remove bolt, Gently pry pin out from thermal beam, then remove from bulkhead studs

    

    

    

    

22. Disconnect powertrain coolant pump connector
    注

    1x locking electrical connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector

    

23. Disconnect battery coolant pump connector
    注

    1x locking electrical connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector

    

24. Raise vehicle fully and lower lift onto locks
    注

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
25. Remove outer fasteners from front aero shield
    注

    7x bolts, 10mm, 5 Nm

    

26. Remove remaining nuts and remove front aero shield from vehicle
    注

    2x nuts, 15mm, 5 Nm

    

27. Position coolant drain container underneath battery coolant pump
28. Remove bolts securing battery coolant pump to Supermanifold
    注

    4x bolts, T20, 1.8 Nm

    

29. Remove battery coolant pump from Supermanifold
    注

    Make sure both o-rings (inner purple, and outer black) come off with old pump

    

    

30. Position battery coolant pump to Supermanifold and install bolts hand tight
    注

    4x bolts, T20, 1.8 Nm, Lubricate both o-rings with silicone o-ring lubricant, Refer to connector position and install coolant pump with connector tab facing up, Recommend installing upper right bolt with coolant pump for easier installation, Make sure the coolant pump is fully seated

    

    

    

31. Remove coolant drain container from underneath vehicle
32. Position the front aero shield to vehicle and install nuts
    注

    2x nuts, 15mm, 5 Nm

    

33. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
    注

    7x bolts, 10mm, 5 Nm

    

34. Lower vehicle until tires are touching the ground
    注

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
35. Torque bolts securing battery coolant pump to supermanifold
    注

    4x bolts, T20, 1.8 Nm

    

36. Connect battery coolant pump connector
    注

    1x locking electrical connector, Engage locking tab

    

37. Connect powertrain coolant pump connector
    注

    1x locking electrical connector, Engage locking tab

    

38. Remove coolant bottle cap

    

39. Place empty coolant container into front storage area

    

40. Fill container with at least 15L of coolant

    

41. Place filled coolant container into front storage area

    

42. Setup vacuum refill tool
    注

    Verify all valves on refill tool are in the closed position, See image for clarity

    

    

43. Install vacuum refill cap onto coolant bottle assembly

    

44. Setup vacuum refill tool
    注

    Verify all valves on refill tool are in the closed position, See image for clarity

    

    

45. Install vacuum refill hose into refill cap on coolant bottle
    注

    Perform push-pull-push test to verify hose is fully installed

    

46. Position overflow hose into empty container

    

47. Connect shop air supply to coolant refill tool
    注

    If not already done, Verify refill valve is set to off

    

48. Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close valve
    注

    Gauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed

    

    

49. Slowly open the refill valve to allow coolant to be drawn into the system
    注

    Make sure hose end of refill hose is fully submerged during entire process

    

50. Once the gauge reads zero, close the refill valve

    

    

51. Once the gauge reads zero, close the refill valve

    

    

52. Once the gauge reads zero, close the refill valve

    

    

53. Once the gauge reads zero, close the refill valve

    

    

54. Disconnect shop air supply from coolant refill tool

    

55. Remove coolant refill hose from coolant container

    

56. Remove coolant overflow hose from coolant container

    

57. Remove vacuum refill hose from refill cap on coolant bottle

    

58. Remove coolant refill tool from vehicle

    

    

59. Remove both coolant containers from inside underhood area

    

60. Connect first responder loop and 12V negative terminal
    注

    1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer

    

    

61. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅 0005 - 维护模式）： PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINSearch for routine in ToolboxStop Thermal Fluid Fill/DrainThermal / Refrigerant System - Stop Thermal Fill/DrainThermal / Coolant System - Stop Thermal Fill/Drainhv / Front Drive Inverter Replacement - Stop Fluid Fill/Drainhv / Rear Drive Inverter Replacement - Stop Fluid Fill/Drainhv / Rear Left Drive Inverter Replacement - Stop Fluid Fill/Drainhv / Rear Right Drive Inverter Replacement - Stop Fluid Fill/Drainhv / Front Drive Unit Replacement - Stop Coolant Fill/Drainhv / Rear Drive Unit Replacement - Stop Coolant Fill/DrainThermal / Actions - Stop Thermal Fill/Drain
    注

    Select ‘X’ at top right of window to close once complete
62. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅 0005 - 维护模式）： TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGESearch for routine in ToolboxCoolant Air PurgeThermal / Coolant System - Coolant Purge Starthv / Front Drive Inverter Replacement - Coolant Air Purgehv / Rear Drive Inverter Replacement - Coolant Air Purgehv / Rear Left Drive Inverter Replacement - Coolant Air Purgehv / Rear Right Drive Inverter Replacement - Coolant Air Purgehv / Front Drive Unit Replacement - Coolant Air Purgehv / Rear Drive Unit Replacement - Coolant Air PurgeThermal / Actions - Coolant Purge Stop or Coolant Purge Start
    注

    Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
63. Inspect coolant level and top off as necessary
    注

    Ensure that the fluid level is at the Max line

    

64. Install coolant bottle cap

    

65. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅 0005 - 维护模式）： TEST-SELF_VCFRONT_X_COOLANT-PUMPS-IDENTIFICATIONSearch for routine in ToolboxCoolant Pumps IdentificationThermal / Coolant System - Pump IdentificationThermal / Actions - Run Coolant Pumps Identification
    注

    Select ‘X’ at top right of window to close once complete, Ensure VCFRONT_a490_coolantPumpsNotIdentified has cleared
66. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅 0005 - 维护模式）： TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCESearch for routine in ToolboxThermal System Performance TestThermal / Actions - Test Thermal Performancehv / Front Drive Inverter Replacement - Thermal System Testhv / Rear Drive Inverter Replacement - Thermal System Testhv / Rear Left Drive Inverter Replacement - Thermal System Testhv / Rear Right Drive Inverter Replacement - Thermal System Testhv / Front Drive Unit Replacement - Thermal System Testhv / Rear Drive Unit Replacement - Thermal System Test
    注

    Select ‘X’ at top right of window to close once complete.
67. Install fresh air intake duct
    注

    1x bolt, 10mm bolt, 4 Nm, 2x clips, 1x pin, Set clips on bulkhead studs, Secure to thermal bar

    

    

    

    

68. Install rear apron
    注

    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

    

    

69. Close hood
70. Remove vehicle from lift
    注

    Lower rack arms fully and remove from under vehicle if necessary, Remove air suspension from "Jack Mode" if equipped