2025-11-04

ECE Headlights - Adjust - Model Y Standard (Tool Method) (Test/Adjust)

교정 코드 17409150 0.24 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-10-23: Released new procedure.

Special tools required for this procedure:

Supplier Part Number Description
Tesla 1133367-00-A Beissbarth Headlight Tester, Model 815

Adjust Headlights using a Headlight Tester

  1. Open the hood.
  2. Enable Service Mode. See 정비 모드.
  3. Enter the headlight aiming mode through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Service > Adjust Headlights.
  4. Enable testdrive override through the touchscreen.
  5. Position the headlight aimer in front of the LH headlight.
    Informational PurposesAn informational icon, calling your attention
    참고
    Position the aimer at approx. 30 cm distance from the surface of the headlamp lens, Adjust the height as necessary to match the center point of the headlamp (~78cm). Make sure that the headlight aimer is on a surface, level with the vehicle.
  6. Power on the headlight aimer.
  7. Use the knobs on the base to adjust headlight aimer level.
  8. Align the headlight aimer perpendicular to vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use visor/laser to line up the tester perpendicular to the axis between furthest fender bolts. If the headlight aimer can move between the RH and LH headlights while maintaining the same laser angle projected onto the fender bolts, it is set correctly (perpendicular) to the vehicle.
  9. Initiate the test on the headlight aimer.
    Informational PurposesAn informational icon, calling your attention
    참고
    Select Test EC > Free Test.
  10. Set up the headlight aimer.
    • Vehicle: Tesla Y
    • Headlight: LHD - EU Asym, RHD - UK
    • Light: Bi-LED
    • Inclinat.: -1.0 %
    • Height: 78 cm
    Informational PurposesAn informational icon, calling your attention
    참고
    Press OK to proceed.
  11. Select OK again to pass fog light settings.
  12. Adjust the headlight aimer to the LH headlight marking.
    Informational PurposesAn informational icon, calling your attention
    참고
    Turn on the laser aimer to adjust the tester's horizontal and vertical position to the LH headlamp marking. Markings can be difficult to spot. Use of a piece of paper can aid in finding the center. Turn off the laser aimer before proceeding to the next step.
  13. Start LH headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    참고
    Select the LH low beam icon and select the low beam button at the bottom of the screen.
  14. Adjust the LH headlight
    Informational PurposesAn informational icon, calling your attention
    참고
    Select Left on the touchscreen, then use the left scroll wheel on the steering wheel to adjust the beam. Target V = -1.0% and H = 0 %. There may be a delay between scroll wheel input and actual light adjustment output. Do not sit in the vehicle as this will affect the headlight height.
  15. Record the results of the headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    참고
    Press the "save" icon.
  16. Position the headlight aimer in front of the RH headlight, and then repeat steps 12 to 15 for the RH headlight.
  17. Review the test results of the headlight aiming.
    Informational PurposesAn informational icon, calling your attention
    참고
    Select the "Save" icon
  18. Move the headlight aimer away from the vehicle.
  19. Exit headlight adjustment mode from the touchscreen.
  20. Exit Service Mode. See 정비 모드.