2023-08-24
Tapp – demper – lampekapsling – par (reparere)
Korrigeringskode 10102318 0.72 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.
ADVARSEL
Kun for Europa: Bare teknikere som har fått opplæring i arbeid med diisocyanater og har fullført alle nødvendige sertifiseringskurs, har tillatelse til å utføre prosedyrer med bruk av uretan og andre produkter som inneholder diisocyanater. Egnet personlig verneutstyr (PVU) må brukes ved arbeid med produkter som inneholder diisocyanater.
- 1460222-00-B - BUMP STOP SOCKET
- 1014689-00-A - MOLYKOTE M-77 PASTE
- 1820212-00-A - BOLT, PANHEAD, M6X16
Repair
- Remove the LH and RH tail light. See Baklys – venstre (fjerne og montere).
- Remove the damaged LH and RH liftgate stop stud from the LH lamp can panel.
-
Measure the diameter of the hole on
the LH and RH lamp can panel that was created after removal of the liftgate stop
stud.
MerkThe diameter of the hole must not exceed 10.5 mm (0.43 in). If the hole is larger, then the panel should be replaced.
-
Apply a shop towel behind the LH and
RH trunk side trim carpet.
MerkPosition the shop towel under the LH and RH lamp can panel to catch metal shavings that are created in the next steps.
-
Drill out the LH and RH lamp can
panel.
MerkDepending on how much rust is present, drill out the hole on each lamp can panel with a 6.5-10.5 mm (1/4 - 13/32 in) drill. Try to remove as much rust as possible but do not exceed 10.5 mm (13/32 in).
- Apply masking tape around the hole on the LH and RH lamp can panel.
-
Sand out any remaining rust on the LH
and RH lamp can panel.
MerkClean with an IPA wipe afterwards and allow 1 minute to dry.
-
Apply self-etching primer onto the LH
and RH lamp can panel.
MerkRecommend to use a brush to apply primer to prevent paint overspray on the body panel when primer spray is used.
- Allow the primer to dry for 5 minutes, and then apply a second coat of primer onto the LH and RH lamp can panel.
- Allow the second coat of primer to dry for 5 minutes, and then apply a third coat of primer to the LH and RH lamp can panel.
- Remove the masking tape from around the hole on the LH and RH lamp can panel.
-
Install the LH and RH rear bodyside
tail light to the vehicle. See Baklys – venstre (fjerne og montere).
MerkInstall new gaskets to each taillight mounting bolt (x2) and the taillight electrical connector housing (x1).
-
Apply approved structural adhesive on
the slotted pan head screws (x2)
- From the inside of the lamp can panel, install the slotted pan head screw onto the LH and RH lamp can panel.
-
Install the LH and RH trunk bump stop
(torque 1.5 Nm).
MerkApply a light coat of Molykote M-77 on the studs.
- Remove the shop towel from behind the LH and RH trunk side trim carpet.
- Install the LH and RH trunk side trim carpet.
- Install the trunk garnish onto the body.