2024-12-10

Slange – bypass for drivverk for fremre drivenhet (varmepumpe) (fjerne og skifte ut)

Korrigeringskode 18302302 0,55 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Denne prosedyren er et UTKAST. Selv om den har blitt godkjent, kan det hende at advarsler og forholdsregler mangler. Følg sikkerhetskravene, og vær ytterst forsiktig ved arbeid på eller nær høyspenningssystemer og -komponenter. Send korrigeringer og tilbakemeldinger til ServiceDevelopment@teslamotors.com.

Fjerne

  1. Raise and support vehicle
  2. Open LH front door
  3. Lower LH front window
  4. Open hood
    Informational PurposesAn informational icon, calling your attention
    Merk
    Press "Open" button on touchscreen to release latch, Lift lid manually
  5. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    Merk
    12x clips, Only store rear apron visible face upwards
  6. Remove cabin intake upper duct assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips, Some configurations may come with 4x clips
  7. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Merk
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  8. Disconnect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
  9. Disconnect first responder loop
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Release locking tab
  10. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects
  11. Remove outer fasteners securing front aero shield
    Informational PurposesAn informational icon, calling your attention
    Merk
    9x bolts, 10mm, 5 Nm
  12. Remove remaining nuts and remove front aero shield from vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 15mm, 5 Nm
  13. Remove clips securing RH front wheel liner to vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips
  14. Use bungee strap to pull back RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Merk
    Secure to subframe
  15. Position coolant drain container underneath RH front of HV battery
  16. Disconnect PT return tube from FDU bypass hose
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips, 2x plugs, Lower hose located on RH front of HV battery, Plug both hose ends
  17. Remove coolant drain container from underneath vehicle

Montere

  1. Release FDU bypass hose from front subframe
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x fir tree clip
  2. Lower vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  3. Position fluid catcher underneath front of vehicle
  4. Disconnect FDU bypass hose from the Supermanifold and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x spring clip, 2x plugs, Plug supermanifold and bypass hose to prevent excess coolant drain
  5. Feed hose into position and install FDU bypass hose to the supermanifold
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x spring clip, 2x plugs, Install plug onto lower end of hose to avoid coolant loss, Remove plug from Supermanifold, Perform push-pull-push test to make sure hose is fully engaged
  6. Remove fluid catcher from underneath vehicle
  7. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  8. Secure FDU bypass hose to front subframe
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x fir tree clip
  9. Position coolant drain container underneath RH front of HV battery
  10. Remove plugs then connect PT return tube to FDU bypass hose
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips, 2x plugs, Perform push-pull-push test to make sure hoses are fully engaged
  11. Remove coolant drain container from underneath vehicle
  12. Release RH front wheel liner from bungee strap
    Informational PurposesAn informational icon, calling your attention
    Merk
    Remove strap from vehicle
  13. Install clips securing RH front wheel liner to vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips
  14. Position front aero shield to vehicle and install nuts
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 15mm, 5 Nm
  15. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
    Informational PurposesAn informational icon, calling your attention
    Merk
    9x bolts, 10mm, 5 Nm
  16. Lower vehicle fully
    Informational PurposesAn informational icon, calling your attention
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  17. Install frunk assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles. Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam
  18. Install bolts securing frunk assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
  19. Install frunk close out panel
    Informational PurposesAn informational icon, calling your attention
    Merk
    4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
  20. Remove coolant bottle cap
  21. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure that fluid level is at Max line
  22. Connect first responder loop
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
  23. Connect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x nut, 10mm, 6 Nm
  24. Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi): TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
  25. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure that fluid level is at Max line
  26. Install coolant bottle cap
  27. Install cabin intake upper duct assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x clips, Some configurations may come with 4x clips
  28. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    Merk
    12x clips
  29. Close hood
  30. Raise LH front window
  31. Close LH front door
  32. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lower rack arms fully and remove from under vehicle