2023-02-06

Ledningsnettet – filter – antenne – venstre (fjerne og skifte ut)

Korrigeringskode 17108302 0.30 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Fjerne

  1. Open all the doors and fully lower all the windows.
    Informational PurposesAn informational icon, calling your attention
    Merk
    If the vehicle is being powered down, latch the rear doors to prevent accidental closure.
  2. Move the LH and RH front seats fully forward.
  3. Remove the LH 2nd row seat side bolster. See Polstring – side – sete – andre rad – venstre (fjerne og skifte ut).
  4. Remove the LH side rail trim. See Kledning – sideskinne – venstre (fjerne og skifte ut).
  5. Remove the LH upper C-pillar trim. See Deksel – C-stolpe – øvre – venstre (fjerne og skifte ut).
  6. Release the clip and tabs (x4) that attach the LH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Pull the rear of the trim forward, and then upward to remove it.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Plastic trim tool
  7. Remove the RH 2nd row seat side bolster. See Polstring – side – sete – andre rad – venstre (fjerne og skifte ut).
  8. Remove the RH side rail trim. See Kledning – sideskinne – venstre (fjerne og skifte ut).
  9. Remove the RH upper C-pillar trim. See Deksel – C-stolpe – øvre – venstre (fjerne og skifte ut).
  10. Release the clip and tabs (x4) that attach the RH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Pull the rear of the trim forward, and then upward to remove it.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Plastic trim tool
  11. Remove the package tray trim. See Kledning – pakkskuff (fjerne og skifte ut).
  12. Disconnect the LH antenna filter harness connector from the LH C-pillar ground.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Hakke miniatyr mykt håndtak, 90 graders spiss, 6 in
  13. Remove the LH antenna filter harness from the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Peel the tape back found at each end of harness housing seal.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Plastic trim tool
  14. Disconnect the LH antenna filter harness connector from the heater grid, and then remove the harness from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Gently disconnect the harness. Do not damage the heater grid.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Hakke miniatyr mykt håndtak, 90 graders spiss, 6 in

Montere

  1. Position the LH antenna filter harness on the vehicle, and then connect the harness connector to the heater grid.
  2. Connect the LH antenna filter harness connector to the LH C-pillar ground.
  3. Install the LH antenna filter harness on the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Apply a small piece of tape at each end of the seal clip.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • Felt tape
    • Scissors
  4. Install the package tray trim. See Kledning – pakkskuff (fjerne og skifte ut).
  5. Install the clip and tabs (x4) that attach the LH rear C-pillar trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Slide the back tabs into package tray, and then push the front tabs toward the rear.
  6. Install the LH upper C-pillar trim. See Deksel – C-stolpe – øvre – venstre (fjerne og skifte ut).
  7. Install the LH side rail trim. See Kledning – sideskinne – venstre (fjerne og skifte ut).
  8. Install the LH 2nd row seat side bolster. See Polstring – side – sete – andre rad – venstre (fjerne og skifte ut).
  9. Raise the LH 2nd row seat.
  10. Repeat step 5 through step 9 for the RH side of the vehicle.
  11. Move the LH and RH front seats to the original positions.
  12. Raise all the windows and close all the doors.