2025-10-24

Grub Screws - Upper Steering Column (Inspect)

Korrigeringskode 32051910 0.18 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til ServiceManualFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2025-10-15: Added steps to set touchscreen to Screen Clean Mode and to clean the touchscreen and suction cup.
  • 2025-03-13: Released new procedure to support Toolbox article 8743800 on lateral steering column stiffness.
Special tools required for this procedure:
  • 1064697-00-B KIT, BRAKE ROTOR RUN OUT
  • 1080978-00-B KIT, FORCE GAUGE MARK-10

Inspect

  1. Move the steering column to the highest and most outward position.
  2. Set steering wheel straight ahead.
  3. Perform a pull/wiggle test on the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Gently pull the steering wheel away from the steering column. Check for any unusual/excessive movement. If excessive movement is found, then first reinstall a new steering wheel bolt and torque it to the specified value before continuing to the next step. See Bolt – ratt til øvre stamme (fjerne og skifte ut).
    Informational PurposesAn informational icon, calling your attention
    Merk
    If the steering wheel bolt was replaced, add correction code 32051842 as a separate activity to the Service Visit.
  4. Apply protection onto the steering wheel and center console.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Apply tape at the 3 o'clock position of the steering wheel and install a fender cover onto the center console.
  5. Set the touchscreen to Cleaning Mode via Controls > Display > Screen Clean Mode.
  6. Use IPA wipes to clean the touchscreen and the adhesion portion of the suction cup from any dirt prior to installing it on the touchscreen. Allow at least one minute for the IPA to dry.
  7. Install brake rotor run out tool onto the touchscreen and steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Install suction cup onto touchscreen. Apply masking tape onto suction cup for protection. Install brake run out tool onto suction cup.
  8. Align the tool horizontally with the tape on the steering wheel. Make sure that the indicator rod is slightly depressed and allows travel in both directions without bottoming out. Set dial to zero.
  9. Install a zip tie onto the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Apply tape around 9 o'clock position of the steering wheel for protection and install the zip tie around to enable a lateral pull movement. Do not fully tighten the zip tie.
  10. Inspect for steering column lateral stiffness.
    1. Make sure the gauge is set to Newtons (N).
    2. Zero out the gauge.
    3. Apply a pull force of 50 N on the steering wheel in the LH lateral direction.
    4. Record the value at which the dial indicator stabilizes.
    5. Apply a push force of 50 N on the steering wheel in the RH lateral direction.
    6. Record the value at which the dial indicator stabilizes.
    7. Calculate the difference between the two values.
      • If the calculated difference is 1.5 mm or less, the steering column lateral stiffness is within the specified tolerance. Continue to the next step.
      • If the calculated difference is more than 1.5 mm, the steering column grub screws need to be reworked. See Kombiskruer – øvre rattstamme (omarbeiding). Add correction code 32051918 as a separate activity to the Service Visit.
  11. Remove the brake rotor run out tool from the touchscreen and steering wheel.
  12. Remove the zip tie and tape from the steering wheel.
  13. Remove the fender cover from the center console.
  14. Use IPA wipes to clean the steering wheel and touchscreen from any residues.
  15. Exit Screen Clean Mode.