Korrigeringskode 11336802 11336902 FRT 0.48 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til ServiceManualFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

1. Open all four doors
   Merk

   If vehicle is being powered down, Latch rear doors to prevent accidental closure

   

2. Lower all four windows

   

3. Remove LH IP end cap
   Merk

   3x clips

   

4. Remove LH mid A-pillar assembly
   Merk

   1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove

   

5. Remove clip for LH lower A-pillar trim
   Merk

   1x push clip

   

6. Remove LH lower A-pillar trim
   Merk

   2x clips, 3 guide tabs, Pull rear of lower A-pillar upward to release clip then pull outward to release front tabs from carpet

   

7. Move LH front seat forward

   

8. Move RH front seat forward

   

9. Remove 2nd row seat cushion
   Merk

   2x tabs, 2x connectors, Slide locking tabs to left of vehicle while lifting up seat bench. Newer models have connectors on both sides of bench, Older models have 2x connectors on one side of bench

   

   

   

   

   

   

   

   

10. Fold 60 seat in down position
    Merk

    Protect the seat cushion

    

11. Remove LH side bolster
    Merk

    1x clip, 2x location pins, Pull outward then slightly upward to remove

    

    

12. Remove and discard bolster plastic bracket from LH side
    Merk

    2x clips, If necessary, depress the clips from behind, This bracket may come out with bolster, Discard after removal

    

13. Fold 60 seat into vertical position
    Merk

    Remove seat protection

    

14. Remove LH rear door sill trim panel
    Merk

    3x clips, 1x guide tab, Pull upward at the lower corner of sill trim to release clip from lower B-pillar, Then remove the remaining clips by pulling away from the body

    

    

15. Release clips securing the LH upper B-pillar assembly and move aside
    Merk

    4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips

    

16. Remove the LH lower B-pillar assembly
    Merk

    1x push clip, 6x clips, Remove the front push clip from lower B-pillar, then pull the top of B-pillar to release top clips then work your way to bottom clips

    

    

    

17. Apply tape to LH door side upper hinge location
    Merk

    This will mark where the hinge should align on install

    

18. Apply tape to LH body side upper hinge location
    Merk

    This will mark where the hinge should align on install

    

19. Support LH rear door
    Merk

    Rest door at first detent, Use soft material to protect painted surface

    

20. Remove fasteners securing LH rear upper door hinge to the LH rear door
    Merk

    2x bolts, 10mm, 27 Nm

    

21. Remove fasteners securing LH rear upper door hinge to body
    Merk

    2x nuts, 13mm, 27 Nm, Support door hinge to ensure it does not fall in the door jam

    

22. Remove LH rear upper door hinge from vehicle
    Merk

    Shift upper section of door outward slightly to create space to remove studs from body

    

23. Install LH rear upper door hinge to vehicle
    Merk

    Shift upper section of door outward slightly to create space to remove studs from body

    

24. Install fasteners securing LH rear upper door hinge to body hand tight
    Merk

    2x nuts, 13mm, 27 Nm, Support door hinge to ensure it does not fall in the door jam, Align hinge with previously applied tape on body

    

25. Install fasteners securing LH rear upper door hinge to the LH rear door hand tight
    Merk

    2x bolts, 10mm, 27 Nm, Align hinge with previously applied tape on door

    

26. Torque fasteners securing LH rear upper door hinge to body
    Merk

    2x nuts, 13mm, 27 Nm

    

27. Torque fasteners securing LH rear upper door hinge to the LH rear door
    Merk

    2x bolts, 10mm, 27 Nm

    

28. Remove support from LH rear door
    Merk

    Rest door at first detent, Use soft material to protect painted surface

    

29. Close the LH rear door to check for gap/flushness
    Merk

    Adjust the LH rear door if necessary

    

30. Remove tape from LH body side upper hinge location

    

31. Remove tape from LH door side upper hinge location

    

32. Clean hinge bolts with IPA
    Merk

    Allow 1 minute dry time

    

33. Apply touch up paint to bolt heads as needed
    Merk

    Make sure to shake touch up paint before applying, Refer to label for dry time instructions

    

34. Install LH lower B-pillar assembly
    Merk

    1x push clip, 6x clips, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips, Install the front push clip then make sure the seal correctly overlaps the trim

    

    

35. Install the LH upper B-pillar assembly
    Merk

    4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim

    

    

    

36. Install LH rear door sill trim panel
    Merk

    3x clips, 1x guide tab, Align the guiding tab to slot, Then push downward to install the clips after aligning them, Make sure the seal sits overlapping the trim. Newer vehicles may not be equipped with metal bracket and a foam insert will be present the bottom of trim piece

    

    

    

37. Fold 60 seat in down position
    Merk

    Protect the seat cushion if necessary

    

38. Install bolster plastic bracket to LH side bolster
    Merk

    2x tabs, Install new bolster bracket

    

39. Install LH side bolster
    Merk

    1x clip, 2x location pins, Align the bottom tab then push inward to install

    

    

40. Fold 60 seat into vertical position
    Merk

    Remove seat cushion protection, Be careful not to pinch the seat belt

    

41. Connect 2nd row seat cushion harness and install 2nd row seat cushion
    Merk

    2x connectors, 2x clips, Insert the seat belt buckles through the holes, Slide rear cushion inward then align front guide tabs to locking tabs, Make sure cushion is fully seated with push pull test near clips

    

    

    

    

    

    

    

    

42. Move RH front seat to original position

    

43. Move LH front seat to original position

    

44. Install LH lower A-pillar trim
    Merk

    2x clips, 3 guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, fully seat seal along trim

    

    

45. Install clip for LH lower A-pillar trim
    Merk

    1x push clip

    

46. Install LH mid A pillar assembly
    Merk

    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A pillar, Pull seal over trim

    

47. Install LH IP end cap
    Merk

    3x clips

    

48. Raise all four windows

    

49. Close all four doors